Hearth and Home Technologies HRV200PLUS manual Fireplace Control Terminals, Thermostat on Mode

Page 31

HRV200PLUS INSTALLATION INSTRUCTIONS

3. Fireplace Control Terminals

 

Fireplace Control Terminals – Connector P9

 

 

 

Input

 

Function

 

 

Dry Contact Output to initiate the fireplace ignition process.

R1

 

Note: Caliber NXT Plus/6100 Plus Applications: R1 sends a 12 VDC

 

 

signal to the fireplace board to initiate the ignition process. R2 has a jumper

 

 

to 12V.

 

 

 

 

 

Dry Contact Output to initiate the fireplace ignition process.

R2

 

Note: Caliber NXT Plus/6100 Plus Applications: R2 has a jumper to 12V.

 

 

R1 sends a 12 VDC signal to the fireplace board to initiate the ignition

 

 

process.

 

 

 

C2**

 

12 VDC Output to energize the electric ember light relay on the

 

fireplace board.

 

 

 

 

 

C1**

 

12 VDC Output to override pressure switch operation during the first

 

thirty seconds of the ignition process.

 

 

 

 

 

Com**

 

12 VDC common output to the fireplace board.

 

 

 

 

 

12 VDC output to the fireplace ON/OFF switch for Novus Plus/6000

12V

 

Plus applications or to the fireplace board for Caliber NXT

 

 

Plus/6100 Plus applications.

 

 

 

HI

 

Fireplace High Fire input to control - 12 VDC.

 

 

 

LO

 

INPUT NOT USED

 

 

 

** These terminals used for Caliber NXT Plus/6100 Plus applications only.

See Figures 18-19 for wiring diagram.

4.Thermostat Operating Modes – Connector “P6”

a.OFF Mode

The HRV is idle until an input is sensed. This is the normal standby state when the HRV Plus is powered but not receiving any command inputs.

b.Thermostat ON Mode

When 24VAC is sensed across the thermostat input terminals (“TSTAT” & “TCOM”), the HRV control executes Fireplace High Fire Mode, as described above. When the 24VAC signal is removed from the Thermostat input terminals, the HRV returns to its previous state.

02/04

4034-102 Rev F

31

Image 31
Contents Heat Recovery Ventilator Installation & Operating InstructionsHRV200PLUS Application Table of ContentsEngineering Data HRV200PLUS Clearance to Combustibles Appliance DimensionsChoose the defrost method best for your application Defrost OptionsNo Defrost Fresh Air Fireplace Defrost Setup for Room Air Defrost OptionSetup for Fresh Air Fireplace Defrost Option Room Air DefrostSimplified Installation Supply/Return Method Installation DiagramsExhaust Air Partially Dedicated InstallationFresh Air Fully Dedicated Installation Electrical Installing the VentilatorInstalling the Drain Line and P-Trap LocationLocate the Fresh Air Inlet Vent and Duct InstallationOptional Alternate Exhaust Damper Assembly StandardDuct the Warmside Air Supply Install Fresh Air Supply DuctingDampers and Grilles Warmside Ducting GuidelinesAssembling the Vent Pipe Sections HRV Plus Exhaust Guidelines Alternate Exhaust Port Exhaust TerminationStale Air from the Living Area to the HRV Alternate Exhaust Horizontal Exhaust Terminations see FiguresTypical Horizontal Termination Horizontal TerminationTermination Cap Locations As specified in CGA B149 Installation Codes Dimension DescriptionsTypical Vertical Termination see Figure Vertical Termination see FigureTypical Vertical Termination Vent Height Chase/Termination InstallationInstalling the Firestop Spacer Firestop Spacer/Vent InstallationNet Air Flow sCFM Selecting Blower SpeedsBalancing Collar Instructions BalancingAir Flow Balancing Pitot Tube Balancing Procedure see Figure Pitot Tube Balancing Flow Station Balancing Flow Station Balancing Procedure see FigureOperating Modes Fireplace Operating Modes Connector P9OFF Mode Fireplace High Fire ModeTermination HRV Defrost Mode∅ d. Novus Plus/6000 Plus Initiation Thermostat on Mode Thermostat Operating Modes Connector P6Fireplace Control Terminals Ventilation Control Terminals Connector P1 Ventilation Operating Modes Connector P1Interlock Mode Furnace Interface Operating Modes Connector P3Furnace Interface Terminals Fireplace Control Wiring Wiring∅ Caliber NXT Plus or 6100 Plus & HRV Wired Together ∅ Novus Plus Control Wiring ∅ 6000 Plus Control Wiring Thermostat Control Wiring Hvac System Thermostat Control WiringVentilation Control Wiring Ventilation Control WiringFurnace Interface Wiring Furnace Interface WiringSemi Annual Maintenance Clean Core Maintenance InstructionsMonthly Maintenance Inspect Exterior Hoods Quarterly MaintenanceInspect and Clean Duct Work if required Annual MaintenanceGeneral Maintenance Inspect and Clean Drain condensate Lines if requiredSummarized Guide 20+3 77.58!$% Installing Remote Controls AccessoriesREPLACEMENT-#$###$+*#!,&#PARTS#$% AHR IndexHRV200PLUS GAS Appliance Limited Warranty

HRV200PLUS specifications

The Hearth and Home Technologies HRV200PLUS is an advanced heat recovery ventilator (HRV) designed to provide optimal indoor air quality while ensuring energy efficiency. As homes become increasingly airtight due to modern construction techniques, the importance of proper ventilation grows. The HRV200PLUS addresses this need by continuously exchanging stale indoor air with fresh outdoor air, effectively maintaining a healthy living environment.

One of the standout features of the HRV200PLUS is its innovative heat recovery technology. This system captures the heat from the outgoing air and transfers it to the incoming fresh air. As a result, the air being brought into the home is pre-warmed, reducing the demand on heating systems during the colder months. This energy-efficient method helps homeowners save on heating costs while maintaining comfort levels inside the home.

Another notable characteristic of the HRV200PLUS is its quiet operation. Equipped with high-performance, low-noise fans, this unit operates in silence, ensuring that occupants can enjoy a peaceful environment without the disruptive sounds often associated with ventilation systems. Additionally, the HRV200PLUS provides versatile installation options, allowing it to be easily integrated into both new and existing homes.

The unit features adjustable settings that allow users to customize airflow according to their specific needs. With multiple fan speeds, homeowners can choose the most suitable option for their daily activities, ensuring an ideal balance between indoor air quality and energy use. Furthermore, the HRV200PLUS includes a built-in filter system that captures dust, allergens, and other airborne particles, enhancing overall air quality.

Durability and ease of maintenance are also keys in the design of the HRV200PLUS. Constructed with high-quality materials, this unit is made to last, reducing the need for frequent replacements. The filters are easily accessible, making periodic maintenance straightforward, which further extends the product's lifespan.

In summary, the Hearth and Home Technologies HRV200PLUS stands out as a premium choice for homeowners seeking a reliable and efficient ventilation solution. Its combination of heat recovery technology, quiet operation, customizable settings, and easy maintenance make it an ideal option for improving indoor air quality while keeping energy costs in check. As the emphasis on healthy living spaces continues to grow, the HRV200PLUS remains a practical investment for modern homes.