Zanussi ZGL 62 ITX Commissioning, Conversion from Natural Gas to LPG, To adjust the gas rate

Page 15

Commissioning

When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below.

-Turn the gas tap to the MAX position and ignite.

-Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times. If the flame is unstable or is extinguished follow the procedure below.

)Procedure:

-Re-ignite the burner and set to MIN.

-Remove the control knob and use a thin bladed screwdriver to turn the adjustment screw until the flame is steady and does not extinguish, when the knob is turned from MIN to MAX.

-The adjustment screw may be located at the centre of the gas tap control shaft or on the gas tap body, left of the control shaft or below (see diagram).

-Repeat the adjustment procedure for all burners.

)Pressure Testing

-Remove left hand pan support and front left burner cap and crown.

-Fit manometer tube over the injector.

-Turn on the burner gas supply and ignite another burner.

-The pressure reading should be nominally 20mbar and must be between 17 mbar and 25mbar.

-Turn off the burner supplies.

Adjustment

screw

Conversion from Natural Gas to LPG

IMPORTANT

The replacement/conversion of the gas hob should only be undertaken by a competent person.

It is important to note that this model is designed for use with natural gas but can be converted for use with butane or propane gas providing the correct injectors are fitted and the gas rate is adjusted to suit.

Method

•Ensure that the gas taps are in the 'OFF' position

•Isolate the hob from the electrical supply

•Remove all pan supports, burner caps, rings, crowns and control knobs.

•With the aid of a 7mm box spanner the burner injectors can then be unscrewed and replaced by the appropriate LPG injectors.

To adjust the gas rate

With the aid of a thin bladed screwdriver completely tighten down the by pass adjustment screw, which is located down the centre of the gas tap control shaft. Upon completion stick the replacement rating plate on the under side of the hob.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents GAS HOB ZGL 62 ITX Service Important Safety InformationInstallation Child SafetyContents Description of the Hob Hob burners OperationBurners Maintenance and CleaningHob Top Pan SupportsSomething Not Working? Symptom SolutionEngineers technical data Instructions for the InstallerImportant safety requirements Provision for ventilationLocation Installation Gas ConnectionCut Out Size Fitting the Hob into the worktop BuildingBuilding over a cupboard or drawer Building over a kitchen unit with doorPermanent Connection Electrical connectionsWiring Diagram Fault FindingPreliminary Electrical Systems Check Ignition System / Gas Ignition To adjust the gas rate CommissioningConversion from Natural Gas to LPG Customer Care Service and Spare PartsEuropean guarantee Page Page 35687-8002 11/06

ZGL 62 ITX specifications

The Zanussi ZGL 62 ITX is an innovative built-in gas hob that boasts a blend of style, functionality, and cutting-edge technology. Designed for the modern kitchen, this appliance caters to both cooking enthusiasts and everyday users alike, delivering an outstanding culinary experience.

One of the standout features of the ZGL 62 ITX is its four gas burners, providing versatility for various cooking techniques. Each burner is engineered to provide precise heat control, which is essential for tasks that require exact temperatures, such as simmering sauces or frying meats. The burners are designed with different power outputs, accommodating everything from gentle simmering to intense boiling.

Safety is a significant consideration in the design of the ZGL 62 ITX. It incorporates a flame failure safety device, a crucial feature that ensures the gas supply is cut off automatically if the flame is accidentally extinguished. This technology gives users peace of mind, focusing on their cooking without worrying about safety hazards.

The ignition system of the ZGL 62 ITX adds to its convenience. With a simple push-and-turn control mechanism, users can ignite the burners with ease, eliminating the need for matches or lighters. This system is designed for quick access, allowing busy cooks to get started on their meals without delay.

In terms of aesthetics, the Zanussi ZGL 62 ITX features a sleek and modern design, with a stylish stainless-steel finish that complements various kitchen decors. The surface is not only beautiful but also practical, as it is easy to clean and maintain. The burners are equipped with enamel supports that provide stability for pots and pans while also being resilient against wear and tear.

Installing the ZGL 62 ITX is straightforward, thanks to its built-in design that fits seamlessly into standard kitchen cabinetry. The control knobs are positioned at the front for easy access, ensuring that users do not have to reach over hot pots and pans during cooking.

Overall, the Zanussi ZGL 62 ITX embodies a perfect harmony of innovative features and stylish design. Whether preparing a simple meal or an elaborate feast, this gas hob offers the reliability, safety, and control that home chefs need, making it an excellent addition to any kitchen. With its combination of function, safety features, and elegant design, the ZGL 62 ITX represents an ideal choice for those who value performance in their culinary endeavors.
Top Page Image Contents