Power Cord and Strain Relief Installation

GE JBP22, JBS56, JBS27, JBS03, JBS07, JBS15, JBP15, JB600 Power Cord and Strain Relief Installation

Page 37

Installation Instructions

3POWER CORD AND STRAIN RELIEF INSTALLATION

ARemove the wire cover (on the lower back of the range) by removing two (2) screws using a 1/4” nut driver.

Do not discard these screws.

2 screws to remove wire cover

Retaining tab

Back of range

Wire cover

BRemove the knockout ring (13⁄8″) located on bracket directly below the terminal block. To remove the knockout, use a pair of pliers to bend the knockout ring away from the bracket and twist until ring is removed.

Terminal block (appearance may vary)

Knockout

Knockout ringring removed in bracket

CFor power cord installations only (see the next step if using conduit), assemble the strain relief in the hole. Insert the power cord through the strain relief and tighten. Allow enough slack to easily attach the cord terminals to the terminal block. If tabs are present at the end of the winged strain relief, they can be removed for better fit.

NOTE: Do not install the power cord without a strain relief. The strain relief bracket should be installed before reinstalling the rear range wiring cover.

Terminal block

Strain relief

Power cord Bracket

Skip to Step 4 or 5.

DFor conduit installations only, purchase a squeeze connector matching the diameter of your conduit and assemble it in the hole. Insert the conduit through the squeeze connector and tighten. Allow enough slack to easily attach the wires to the terminal block.

NOTE: Do not install the conduit without a squeeze connector. The squeeze connector should be installed before reinstalling the rear range wiring cover.

Terminal block

Squeeze

connector

ConduitBracket

Skip to Step 6 or 7.

Image 37

Contents

Write the model and serial numbers here Model # Serial # RangesElectric Coil & RadiantImportant Safety Information Operating Installation InstructionsGe.com InstructionsOven Operating Instructions Care and Cleaning InstallationConsumer Support Instructions InstallationOperating Instructions Support Troubleshooting TipsConsumer Safety Using the surface unitsHow to Set Temperature Limiter CleaningCare About the radiant surface units…Selecting types of cookware Safety Instructions Using the oven controls. on some modelsInstallation Instructions Safety Instructions Oven Control, Clock and Timer Features and SettingsOven Temperature Knob on some models Using the ovenBefore you begin… Broiling Guide Never cover the oven bottom with aluminum foilBroil HI/LO pad again Broiling Guide Operating InstructionsTo Set the Timer Using the clock and timer. on some modelsTouch the Kitchen Timer ON/OFF or Timer ON/OFF pad To Set the ClockTo Cancel the Timer To Reset the TimerPower Outage End of Cycle Tones on some modelsHow to Set a Delayed Start and Automatic Stop How to Set an Immediate Start and Automatic StopHour Shut-Off Special features of your oven controlHow to Set for Regular Baking/Roasting Using the Sabbath Feature. on some modelsTroubleshooting Tips Consumer Support Designed for use on the Jewish Sabbath and HolidaysHow to Exit the Sabbath Feature To Adjust the Thermostat with this Type of Knob Adjust the oven thermostat-Easy to do yourselfTo Adjust the Thermostat on Other Models When Using the Warming Drawer SafetyTo Crisp Stale Items Temperature Selection ChartRack on some models Troubleshooting Using the self-cleaning oven. on some modelsOperating TipsTo Stop a Clean Cycle How to Delay the Start of CleaningAfter a Clean Cycle To clean the inside of the door Care and cleaning of the rangeTo clean the outside of the door Lift-Off Oven DoorOven Heating Elements Oven Light Replacement on some modelsOven Shelves To remove the coverControl Panel and Knobs Broiler Pan & GridTo remove the storage drawer To replace the storage drawer Removable Warming Drawer on some models Warming Drawer Rack on some modelsTo replace the warming drawer To remove the warming drawerLift-Up Cooktop on some models Porcelain Enamel Cooktop on some modelsTo remove a surface unit To replace a surface unitOven Vent Painted Surfaces on some models Safety InstructionsStainless Steel Surfaces on some models Any other materialNormal Daily Use Cleaning Cleaning the glass cooktop. on some modelsOperating Instructions Burned-On Residue Metal Marks and Scratches Instructions Operating Cooktop Seal To Order PartsInstallation Instructions Prepare to Install the Range Electrical Connections Power Cord and Strain Relief Installation Electrical Connections Wire Conduit Installation Install the Range Operation Checklist Before you call for service… Instructions Or delay start Display flashes bAd Control signals afterFood does not Broil properlyClock and timer do Oven temperature tooPower outage Hot or too coldDuring a clean cycle Self-Cleaning ModelsNot unlock Oven not clean after a Clean cycleLooking For Something More? AccessoriesConsumer Support Troubleshooting Tips We’ll Cover Any Appliance. Anywhere. Anytime Consumer Product Ownership Registration GE Will Provide Electric Range WarrantyWhat GE Will Not Cover One YearParts and Accessories Schedule ServiceConsumer Support GE Appliances Website Real Life Design Studio

Related manuals