GE RB536, JBS56, JBS27, JBS03, JBS07, JBS15, JBP15, JB600, JBP22, RB740, RB526 manual Electrical Connections

Page 38

Installation Instructions

ELECTRICAL CONNECTIONS (CONT.)

43-WIRE POWER CORD INSTALLATION

WARNING: The neutral or ground wire of the power cord must be connected

to the neutral terminal located in the center of the terminal block. The power leads must be connected to the lower left and the lower right terminals of the terminal block.

ARemove the 3 lower terminal screws from the terminal block. Insert the 3 terminal screws through each power cord terminal ring and into the lower terminals of the terminal block. Be certain that the center wire (white/neutral) is connected to the center lower position of the terminal block. Tighten screws securely into the terminal block.

DO NOT remove the ground strap connection.

Terminal block (appearance may vary)

Neutral terminal

Ground plate

Ground strap

54-WIRE POWER CORD INSTALLATION

WARNING: The neutral wire of the supply circuit must be connected to the

neutral terminal located in the lower center of the terminal block. The power leads must be connected to the lower left and the lower right terminals of the terminal block. The 4th grounding lead must be connected to the frame of the range with the ground plate and the ground screw.

ARemove the 3 lower terminal screws from the terminal block. Remove the ground screw and ground plate and retain them.

BCut and discard the ground strap. DO NOT DISCARD ANY SCREWS.

CInsert the one ground screw into the power cord ground wire terminal ring, through the ground plate and into the frame of the range.

DInsert the 3 terminal screws (removed earlier) through each power cord terminal ring and into the lower terminals of the terminal block. Be certain that the center wire (white/neutral) is connected to the center lower position of the terminal block. Tighten screws securely into the terminal block.

Before

Ground strap

 

Terminal

or

block

 

Ground strap

Neutral

terminal

 

Power cord

BSkip to Step 8 and proceed with the installation.

After

Terminal block

Ground

screw

Neutral terminal

Ground plate (grounding to range)

E

Skip to Step 8 and proceed with the installation.

38

Page 37 Page 39
Image 38
Page 37 Page 39
Contents
RangesElectric Coil & Radiant Write the model and serial numbers here Model # Serial #Important Safety Information Ge.com Installation InstructionsOperating InstructionsOperating Instructions Care and Cleaning Installation OvenOperating Instructions Instructions InstallationConsumer Support Consumer Troubleshooting TipsSupport How to Set Using the surface unitsSafety Care CleaningTemperature Limiter About the radiant surface units…Selecting types of cookware Installation Instructions Using the oven controls. on some modelsSafety Instructions Oven Control, Clock and Timer Features and Settings Safety InstructionsBefore you begin… Using the ovenOven Temperature Knob on some models Broil HI/LO pad again Never cover the oven bottom with aluminum foilBroiling Guide Operating Instructions Broiling GuideTouch the Kitchen Timer ON/OFF or Timer ON/OFF pad Using the clock and timer. on some modelsTo Set the Timer To Set the ClockPower Outage To Reset the TimerTo Cancel the Timer End of Cycle Tones on some modelsHow to Set an Immediate Start and Automatic Stop How to Set a Delayed Start and Automatic StopSpecial features of your oven control Hour Shut-OffTroubleshooting Tips Consumer Support Using the Sabbath Feature. on some modelsHow to Set for Regular Baking/Roasting Designed for use on the Jewish Sabbath and HolidaysHow to Exit the Sabbath Feature To Adjust the Thermostat on Other Models Adjust the oven thermostat-Easy to do yourselfTo Adjust the Thermostat with this Type of Knob Safety When Using the Warming DrawerRack on some models Temperature Selection ChartTo Crisp Stale Items Operating Using the self-cleaning oven. on some modelsTroubleshooting TipsAfter a Clean Cycle How to Delay the Start of CleaningTo Stop a Clean Cycle To clean the outside of the door Care and cleaning of the rangeTo clean the inside of the door Lift-Off Oven DoorOven Shelves Oven Light Replacement on some modelsOven Heating Elements To remove the coverTo remove the storage drawer To replace the storage drawer Broiler Pan & GridControl Panel and Knobs To replace the warming drawer Warming Drawer Rack on some modelsRemovable Warming Drawer on some models To remove the warming drawerTo remove a surface unit Porcelain Enamel Cooktop on some modelsLift-Up Cooktop on some models To replace a surface unitStainless Steel Surfaces on some models Painted Surfaces on some models Safety InstructionsOven Vent Any other materialOperating Instructions Cleaning the glass cooktop. on some modelsNormal Daily Use Cleaning Burned-On ResidueCooktop Seal Instructions OperatingMetal Marks and Scratches To Order Parts Installation Instructions Prepare to Install the Range Electrical Connections Power Cord and Strain Relief Installation Electrical Connections Wire Conduit Installation Install the Range Operation Checklist Before you call for service… Instructions Food does not Control signals afterOr delay start Display flashes bAd Broil properlyPower outage Oven temperature tooClock and timer do Hot or too coldNot unlock Oven not clean after a Self-Cleaning ModelsDuring a clean cycle Clean cycleAccessories Looking For Something More?Consumer Support Troubleshooting Tips We’ll Cover Any Appliance. Anywhere. Anytime Consumer Product Ownership Registration What GE Will Not Cover Electric Range WarrantyGE Will Provide One YearConsumer Support GE Appliances Website Schedule ServiceParts and Accessories Real Life Design Studio
Related manuals
Manual 80 pages 13.92 Kb Manual 52 pages 54.79 Kb Manual 44 pages 43.73 Kb
Top Page Image Contents