GE EGR2001, EGR2002, JGBP33, JGBP29, JGBP28, JGBP32 manual Before you begin…, Oven Vent

Page 12

Instructions

 

 

 

 

 

 

Using the oven.

To avoid possible burns, place the shelves in the desired position before you turn the oven on.

Safety

Operating Instructions

The oven has 5 shelf positions.

It also has a special low shelf position (R) for extra large items, such as a large turkey.

Before you begin…

The shelves have stop-locks, so that when placed correctly on the shelf supports (A through E), they will stop before coming completely out, and will not tilt.

When placing and removing cookware, pull the shelf out to the bump on the shelf support.

To remove a shelf, pull it toward you, tilt the front end up and pull it out.

To replace, place the end of the shelf (stop-locks) on the support, tilt up the front and push the shelf in.

NOTE: The shelf is not designed to slide out at the special low shelf (R) position.

Care and Cleaning

Plastic items on the cooktop may melt if left too close to the vent.

Vent appearance and location vary.

Oven Vent

Your oven is vented through ducts at the rear of the range. Do not block these ducts when cooking in the oven—it is important that the flow of hot air from the oven and fresh air to the oven burner be uninterrupted. Avoid touching the vent openings or nearby surfaces during oven or broiler operation—they may become hot.

■Handles of pots and pans on the cooktop may become hot if left too close to the vent.

■Do not leave plastic or flammable items on the cooktop—they may melt or ignite if left too close to the vent.

■Do not leave closed containers on the cooktop. The pressure in closed containers may increase, which may cause them to burst.

■Metal items will become very hot if they are left on the cooktop, and could cause burns.

Installation

Instructions

Power Outage

Tips

CAUTION: Do not make any attempt to operate the electric ignition oven during an electrical power failure.

The oven or broiler cannot be lit during a power failure. Gas will not flow unless the glow bar is hot.

If the oven is in use when a power failure occurs, the oven burner shuts off and cannot be re-lit until power is restored. This is because the flow of gas is automatically stopped and will not resume when power is restored until the glow bar has reached operating temperature.

Troubleshooting

Consumer Support

Oven Light (on some models)

Touch the Oven Light On/Off pad on the upper control panel to turn the light on or off.

Oven Light (on some models)

Press the Oven Light On/Off pad on the lower control panel to turn the light on or off.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Ge.com Write the model and serial numbers here Model # Serial #What to do if YOU Smell GAS Installation Instructions Ge.comSafety Precautions Surface Burners InstructionsCook Meat and Poultry THOROUGHLY… Electric Warming Drawer on some models Operating InstructionsUsing the gas surface burners How to Select Flame SizeBefore Lighting a Gas Burner Sealed Gas BurnersCase of Power Failure Top-of-Range CookwareUsing the oven controls CareOven Temperature Knob on some models Before you begin… Oven VentHow to Set the Oven for Baking or Roasting Preheating and Pan PlacementTroubleshooting Tips Consumer Support Aluminum FoilUsing the oven How to Set the Oven for BroilingBroiling Guide Hi BroilUsing the clock and timer. on some models To Set the TimerTo Set the Clock To Turn Off the Clock DisplayTo Reset the Timer To Cancel the TimerPower Outage Touch the Kitchen Timer On/Off pad twiceHow to Set an Immediate Start and Automatic Stop How to Set a Delayed Start and Automatic StopSpecial features of your oven control. on some models Hour Shut-OffUsing the Sabbath Feature. on some models How to Set for Regular Baking/RoastingDesigned for use on the Jewish Sabbath and Holidays Operating Instructions Adjust the oven thermostat-Do it yourself To Adjust the Thermostat on some modelsTo Adjust the Thermostat on models with an Oven Temp Knob Care and CleaningWhen Using the Warming Drawer On Signal LightTemperature Selection Chart To Crisp Stale ItemsUsing the self-cleaning oven Before a Clean CycleHow to Set the Oven for Cleaning How to Delay the Start of Cleaning on some models To Stop a Clean Cycle on some modelsAfter a Clean Cycle on some models Care and cleaning of the range Standard Twin Burner Assemblies on some modelsInstructions Burner Caps and Heads Burner capsBurner Grates Cooktop SurfaceStainless Steel Surfaces on some models To clean the inside of the door Lift-Off Oven DoorOven Bottom Removable Storage Drawer on some models Safety Instructions Removable Kick Panel on some modelsRemovable Warming Drawer on some models Oven Air Vents Lower Control Panel Front Manifold Panel and KnobsTo raise the cooktop Oven Light Replacement Oven ShelvesDo not remove any screws to remove the cover To replace coverFor Your Safety Part IncludedTools YOU will Need Materials YOU MAY NeedInstallation Instructions Dimensions and Clearances ANTI-TIP Device LocationConnect the Range to GAS Provide Adequate GAS SupplyInstallation Instructions Rigid Pipe Hookup Options Pressure regulator Manifold pipe Electrical Connections Electrical RequirementsCheck Ignition of Surface Burners Seal the OpeningsCheck Ignition of Oven Burner Leveling the Range To remove the oven bottomInstalling the ANTI-TIP Device When ALL Hookups are CompletedBefore you call for service… See the Using the clock and timer section See the Care and cleaning of the range sectionSee the Installation of the range section Oven temperatureAfter a clean cycle Oven not clean after Clean cycleSelf clean light on When trying to set aPower outage Display goes blankDisplay flashes Unable to getCare and Cleaning We’ll Cover Any Appliance. Anywhere. Anytime Consumer Product Ownership Registration Accessories Looking For Something More?GE Will Replace What GE Will Not CoverOne Year Care and Cleaning Mabe Will ReplaceWhat Mabe Will Not Cover Schedule Service Parts and AccessoriesConsumer Support GE Appliances Website Real Life Design Studio
Top Page Image Contents