GE JGBP29, EGR2001, EGR2002, JGBP33 Installing the ANTI-TIP Device, When ALL Hookups are Completed

Page 45

Installation Instructions

9INSTALLING THE ANTI-TIP DEVICE

WARNING!

Range must be secured with an approved Anti-Tip device.

Unless properly installed, the range could be tipped by you or a child standing, sitting or leaning on an open door.

After installing the Anti-Tip device, verify that it is in place by carefully attempting to tilt the range forward.

This range has been designed to meet all recognized industry tip standards for all normal conditions.

The use of this device does not preclude tipping of the range when not properly installed.

If the Anti-Tip device supplied with the range does not fit this application, use the universal Anti-Tip device WB2X7909.

A.Mark the wall where the RIGHT EDGE of the range is to be located. Be sure to allow for the countertop overhang if you intend to install the range next to cabinets.

Anti-Tip

device

Slotted head

screw

Wallplate Approx. 20°

2 18Marked edge of range

B. Locate the outside edge of the device 218 ″ toward the center of the range from the marked edge of the range.

C. Using the device as a template, mark the position of the hole for the screw.

D. For wood construction, drill a pilot hole at an angle of 20 degrees from the horizontal. A nail or awl may be used if a drill is not available.

Mount the Anti-Tip device with the screw provided.

For cement or concrete construction, you will need a 1/4″ x 112″ lag bolt and a 1/2″ O.D. sleeve anchor, which are not provided. Drill the recommended size hole for the hardware.

9INSTALLING THE ANTI-TIP DEVICE (CONT.)

Wallboard

Back of range

Anti-Tip device

Wood screw

Install the sleeve anchor into the drilled hole and then install the lag bolt through the device. The bolts must be properly tightened as recommended for the hardware.

E. Slide the range against the wall, and check for proper installation by grasping the front edge of the cooktop and carefully attempting to tilt the range forward.

WHEN ALL HOOKUPS ARE

COMPLETED

Make sure all controls are left in the off position. Make sure the flow of combustion and ventilation air to the range is unobstructed.

CONVERTING TO LP GAS (or converting back to natural gas from LP)

This range leaves the factory set for use with natural gas. If you want to convert to LP gas, the conversion must be performed by a qualified LP gas installer.

The conversion instructions and LP orifices can be found attached to the range next to the pressure regulator.

Keep these instructions and the orifices in case you want to convert back to natural gas.

45

Image 45
Contents Write the model and serial numbers here Model # Serial # Ge.comWhat to do if YOU Smell GAS Ge.com Installation InstructionsSafety Precautions Instructions Surface BurnersCook Meat and Poultry THOROUGHLY… Operating Instructions Electric Warming Drawer on some modelsHow to Select Flame Size Using the gas surface burnersBefore Lighting a Gas Burner Sealed Gas BurnersTop-of-Range Cookware Case of Power FailureCare Using the oven controlsOven Temperature Knob on some models Oven Vent Before you begin…Preheating and Pan Placement How to Set the Oven for Baking or RoastingTroubleshooting Tips Consumer Support Aluminum FoilHow to Set the Oven for Broiling Using the ovenBroiling Guide Hi BroilTo Set the Timer Using the clock and timer. on some modelsTo Set the Clock To Turn Off the Clock DisplayTo Cancel the Timer To Reset the TimerPower Outage Touch the Kitchen Timer On/Off pad twiceHow to Set a Delayed Start and Automatic Stop How to Set an Immediate Start and Automatic StopHour Shut-Off Special features of your oven control. on some modelsUsing the Sabbath Feature. on some models How to Set for Regular Baking/RoastingDesigned for use on the Jewish Sabbath and Holidays Operating Instructions To Adjust the Thermostat on some models Adjust the oven thermostat-Do it yourselfTo Adjust the Thermostat on models with an Oven Temp Knob Care and CleaningOn Signal Light When Using the Warming DrawerTo Crisp Stale Items Temperature Selection ChartUsing the self-cleaning oven Before a Clean CycleHow to Set the Oven for Cleaning How to Delay the Start of Cleaning on some models To Stop a Clean Cycle on some modelsAfter a Clean Cycle on some models Standard Twin Burner Assemblies on some models Care and cleaning of the rangeInstructions Burner caps Burner Caps and HeadsBurner Grates Cooktop SurfaceStainless Steel Surfaces on some models To clean the inside of the door Lift-Off Oven DoorOven Bottom Removable Storage Drawer on some models Safety Instructions Removable Kick Panel on some modelsRemovable Warming Drawer on some models Oven Air Vents Lower Control Panel Front Manifold Panel and KnobsTo raise the cooktop Oven Shelves Oven Light ReplacementDo not remove any screws to remove the cover To replace coverPart Included For Your SafetyTools YOU will Need Materials YOU MAY NeedInstallation Instructions Dimensions and Clearances Location ANTI-TIP DeviceProvide Adequate GAS Supply Connect the Range to GASInstallation Instructions Rigid Pipe Hookup Options Pressure regulator Manifold pipe Electrical Requirements Electrical ConnectionsCheck Ignition of Surface Burners Seal the OpeningsCheck Ignition of Oven Burner To remove the oven bottom Leveling the RangeWhen ALL Hookups are Completed Installing the ANTI-TIP DeviceBefore you call for service… See the Care and cleaning of the range section See the Using the clock and timer sectionSee the Installation of the range section Oven temperatureClean cycle After a clean cycle Oven not clean afterSelf clean light on When trying to set aDisplay goes blank Power outageDisplay flashes Unable to getCare and Cleaning We’ll Cover Any Appliance. Anywhere. Anytime Consumer Product Ownership Registration Looking For Something More? AccessoriesGE Will Replace What GE Will Not CoverOne Year Care and Cleaning Mabe Will ReplaceWhat Mabe Will Not Cover Parts and Accessories Schedule ServiceConsumer Support GE Appliances Website Real Life Design Studio