GE JGBP28, EGR2001, EGR2002, JGBP33, JGBP29, JGBP32 manual Burner Caps and Heads, Burner caps

Page 28

Care and cleaning of the range.

	Operating	Instructions

	Care and Cleaning

	Installation	Instructions

	Troubleshooting Tips

	ConsumerSupport

Use a sewing needle or twist-tie to unclog the small hole in the burner head.

Burner Caps and Heads

NOTE: Before removing the burner caps and heads, remember their size and location. Replace them in the same location after cleaning.

Burner caps

Lift off when cool. Wash burner caps in hot, soapy water and rinse with clean water. You may scour with a plastic scouring pad to remove burned-on food particles.

Burner heads

For proper ignition, make sure the small hole in the section that fits over the electrode is kept open. A sewing needle or wire twist-tie works well to unclog it.

The slits in the burner heads must be kept clean at all times for an even, unhampered flame.

Clogged or dirty burner ports or electrodes will not allow the burner to operate properly.

Any spill on or around an electrode must be carefully cleaned. Take care to not hit an electrode with anything hard or it could be damaged.

You should clean the burner caps and burner heads routinely, especially after bad spillovers, which could clog the openings in the burner heads. Lift off when cool.

To remove burned-on food, soak the burner heads in a solution of mild liquid detergent and hot water for 20–30 minutes. For more stubborn stains, use a toothbrush.

After cleaning

Before putting the burner caps and heads back, shake out excess water and then dry them thoroughly by setting in a warm oven for 30 minutes.

NOTE: Do not use steel wool or scouring powders to clean the burners.

Replacement

Replace burner heads over the electrodes on the cooktop, in the correct locations according to their size.

On some models:

Medium head

Small head

and cap

and cap

	Front of range
Large head	Large		head

and cap	and cap

On some models:

Medium head

Small head

and cap

and cap

	Front of range
Medium head
	Large head
and cap	and cap

Make sure the slot in the burner head is positioned over the electrode.

Replace the matching size caps onto the heads.

Make sure that the heads and caps are replaced in the correct locations.

NOTE: On some models, the burners are all the same size and power.

28

Image 28

Contents Ge.com Write the model and serial numbers here Model # Serial #What to do if YOU Smell GAS Installation Instructions Ge.comSafety Precautions Surface Burners InstructionsCook Meat and Poultry THOROUGHLY… Electric Warming Drawer on some models Operating InstructionsUsing the gas surface burners How to Select Flame SizeBefore Lighting a Gas Burner Sealed Gas BurnersCase of Power Failure Top-of-Range CookwareUsing the oven controls CareOven Temperature Knob on some models Before you begin… Oven VentHow to Set the Oven for Baking or Roasting Preheating and Pan PlacementTroubleshooting Tips Consumer Support Aluminum FoilUsing the oven How to Set the Oven for BroilingBroiling Guide Hi BroilUsing the clock and timer. on some models To Set the TimerTo Set the Clock To Turn Off the Clock DisplayTo Reset the Timer To Cancel the TimerPower Outage Touch the Kitchen Timer On/Off pad twiceHow to Set an Immediate Start and Automatic Stop How to Set a Delayed Start and Automatic StopSpecial features of your oven control. on some models Hour Shut-OffHow to Set for Regular Baking/Roasting Using the Sabbath Feature. on some modelsDesigned for use on the Jewish Sabbath and Holidays Operating Instructions Adjust the oven thermostat-Do it yourself To Adjust the Thermostat on some modelsTo Adjust the Thermostat on models with an Oven Temp Knob Care and CleaningWhen Using the Warming Drawer On Signal LightTemperature Selection Chart To Crisp Stale ItemsBefore a Clean Cycle Using the self-cleaning ovenHow to Set the Oven for Cleaning To Stop a Clean Cycle on some models How to Delay the Start of Cleaning on some modelsAfter a Clean Cycle on some models Care and cleaning of the range Standard Twin Burner Assemblies on some modelsInstructions Burner Caps and Heads Burner capsCooktop Surface Burner GratesStainless Steel Surfaces on some models Lift-Off Oven Door To clean the inside of the doorOven Bottom Removable Kick Panel on some models Removable Storage Drawer on some models Safety InstructionsRemovable Warming Drawer on some models Lower Control Panel Front Manifold Panel and Knobs Oven Air VentsTo raise the cooktop Oven Light Replacement Oven ShelvesDo not remove any screws to remove the cover To replace coverFor Your Safety Part IncludedTools YOU will Need Materials YOU MAY NeedInstallation Instructions Dimensions and Clearances ANTI-TIP Device LocationConnect the Range to GAS Provide Adequate GAS SupplyInstallation Instructions Rigid Pipe Hookup Options Pressure regulator Manifold pipe Electrical Connections Electrical RequirementsSeal the Openings Check Ignition of Surface BurnersCheck Ignition of Oven Burner Leveling the Range To remove the oven bottomInstalling the ANTI-TIP Device When ALL Hookups are CompletedBefore you call for service… See the Using the clock and timer section See the Care and cleaning of the range sectionSee the Installation of the range section Oven temperatureAfter a clean cycle Oven not clean after Clean cycleSelf clean light on When trying to set aPower outage Display goes blankDisplay flashes Unable to getCare and Cleaning We’ll Cover Any Appliance. Anywhere. Anytime Consumer Product Ownership Registration Accessories Looking For Something More?What GE Will Not Cover GE Will ReplaceOne Year Mabe Will Replace Care and CleaningWhat Mabe Will Not Cover Schedule Service Parts and AccessoriesConsumer Support GE Appliances Website Real Life Design Studio