GE LGB128, JGBS02 Sealed Burner Assemblies on some models, For proper ignition

Page 22
After cleaning, make sure the slot in the burner head is positioned over the electrode.

CARE AND CLEANING

(continued)

CAUTION: DO NOT OPERATE THE BURNER WITHOUT ALL BURNER PARTS AND DRIP PANS (IF SO EQUIPPED) IN PLACE.

Sealed Burner Assemblies (on some models)

Grate

Burner cap

Drip pan

(on some models)

Burner head

Electrode

Turn all controls OFF before removing the burner parts and drip pans (if so equipped).

The burner grates, caps, burner heads and drip pans (if so equipped) can be lifted off, making them easy to clean.

The electrode of

 

the spark igniter is

Electrode

exposed when the

 

burner head is removed. When one

burner is turned to LITE, all the burners spark. Do not attempt to disassemble or clean around any burner while another burner is on. An electric shock may result, which could cause you to knock over hot cookware.

Burner Heads (on sealed burners only)

NOTE: Before removing the burner heads and caps, remember their size and location. Replace them in the same location after cleaning.

For proper ignition,

make sure the small hole in the section that fits over the electrode is kept open. A sewing needle or wire twist-tie works well to unclog it.

The slits in the burner heads of your range must be kept clean at all times for an even, unhampered flame.

You should clean the surface burners routinely, especially after bad spillovers, which could clog these openings.

To remove burned-on food, soak the burner heads in a solution of mild liquid detergent and hot water for 20-30 minutes. For more stubborn stains, use a toothbrush.

Before putting the burner head back, shake out excess water and then dry it thoroughly by setting it in a warm oven for 30 minutes.

Replace the burner heads and caps. Make sure that the heads and

caps are replaced in the correct location. There is one small, 2 medium and one large head and cap.

NOTE: On some models the burner heads and caps are all the same size and can be used in any of the 4 needed locations.

Burner Caps (on sealed burners only)

Lift off when cool. Wash burner caps in hot, soapy water and rinse with clean water. You may scour with a plastic scouring pad to remove burned-on food particles.

Dry them in a warm oven or with a cloth—don’t reassemble them wet. Replace the burner caps.

Make sure that caps are replaced on the correct size burner. There is one small, 2 medium and one large cap.

22

small

medium

small

 

medium

 

 

large

medium

large

 

 

 

 

Front of Range

NOTE: On some models the caps are all the same size and can be used in any of the 4 needed locations.

Page 21 Page 23
Image 22
Page 21 Page 23
Contents RangesXL44 Gas Read this manual carefully Save time and money. Before you request service…Help US Help YOU… If you received a damaged range…When You Get Your Range Important Safety InstructionsUsing Your Range Surface Cooking Do not allow anyone to climb, stand orSave These INSTRUCTIONS5 Cleaning Your RangeBaking, Broiling and Roasting Features of Your Range Features and appearance varyOven Control SeeSurface Burners, Grates and Drip Pans on some models Oven Shelves with Stop-Locks Number of shelves variesBefore Lighting a Burner Surface CookingSurface Burner Controls To Light a Surface BurnerTop-of-Range Cookware How to Select Flame SizeDo not use a wok on any other support ring To Change or Cancel the Timer Setting Clock and TimerTo Set the Timer Display Clock While Timer Is OperatingUsing Your Oven Shelf Positions Oven ShelvesOven Vents To avoid possible burns, place the shelves How to Set Your Range for BakingBaking Type of Food Shelf PositionBaking Guides Pan PlacementPreheating CookiesBaking Pans PiesCakes Don’t PeekTo Adjust the Thermostat Adjust the Oven ThermostatType of Margarine Will Affect Baking Performance Use of Aluminum Foil RoastingDual Shelf Cooking Roasting Guide Questions and AnswersFrozen Roasts Broiling Why are my meats not turning out as brown as they should?Should I salt the meat before broiling? Broiling Guide Ground BeefCare and Cleaning Standard Twin Burners on some modelsSealed Burner Assemblies on some models For proper ignitionCooktop Surface Burner GratesOven Bottom Removable Broiler Drawer on some models Oven Light Bulb on some modelsControl Panel and Knobs Broiler Pan and GridRemovable Storage Drawer on some models Oven Air VentsRemovable Kick Panel on some models Lift-Off Oven Door Outside of doorStainless Steel Surfaces on some models Installation Instructions For Your SafetyImportant Safety Instructions General Provide Adequate GAS Supply Connect the Range to GAS Extension Cord Cautions Electrical RequirementsIMPORTANT-Please read carefully Electrical Connections Seal the Openings Electric Ignition Models Yellow flamesTo remove the oven bottom To remove the broiler drawer Leveling legs can be ⁄ 8 ″ Converting to LP GAS Page QUESTIONS? Before YOU Call for SERVICE… Problem Possible CauseDo It Yourself section We’ll Cover Any Appliance. Anywhere. Anytime Consumer Product Ownership Registration Consumer Support GE Appliances Website Warranty

JGBS02, LGB128 specifications

The GE LGB128 and JGBS02 are two advanced gas turbine models that represent the cutting edge of power generation technology. These turbines are engineered by General Electric, a leader in energy solutions. Both models are designed to enhance efficiency, reduce emissions, and provide reliable power for various applications.

The GE LGB128 is a robust gas turbine characterized by its modular design, which simplifies maintenance and installation processes. This turbine is known for its high efficiency, with a thermal efficiency rating that can reach above 60%. The LGB128 utilizes advanced aerodynamics in its compressor and turbine sections, optimizing performance across a wide range of operating conditions.

One of the key features of the LGB128 is its use of advanced materials and coatings that enhance durability and performance. The turbine blades are crafted from state-of-the-art alloys that can withstand extremely high temperatures, ensuring longevity and reliability. Furthermore, the LGB128 is equipped with sophisticated control systems that leverage machine learning algorithms, enabling real-time optimization of operation and maintenance schedules.

On the other hand, the GE JGBS02 gas turbine is recognized for its versatility and adaptability in various power generation applications. This model is particularly notable for its ability to utilize multiple fuel sources, including natural gas and biogas, which gives it a significant advantage in sustainability. The JGBS02 incorporates advanced combustion technologies that minimize nitrogen oxide (NOx) emissions, making it an environmentally friendly choice for both industrial and utility-scale power generation.

A prominent characteristic of the JGBS02 is its compact design, allowing for flexible installation in limited spaces. This feature is crucial for projects where space is a constraint. Additionally, the turbine is equipped with an intelligent monitoring system that continuously assesses performance metrics, providing operators with valuable insights into efficiency and potential maintenance needs.

Both the LGB128 and JGBS02 are designed to provide reliable performance in today's demanding energy landscape. Their capabilities make them suitable for various applications, including combined cycle power plants and peak shaving operations. As the world pivots toward cleaner energy solutions, these GE turbines embody the technological advancements necessary for fostering a sustainable future in power generation. With their commitment to efficiency, durability, and environmental responsibility, the LGB128 and JGBS02 stand at the forefront of modern energy technology.
Top Page Image Contents