GE JGBS02, LGB128 installation instructions Provide Adequate GAS Supply

Page 31

1 PROVIDE ADEQUATE GAS SUPPLY

Your range is designed to operate at a pressure of 4″ of water column on natural gas or, if designed for LP gas (propane or butane), 10″ of water column. Make sure you are supplying your range with the type of gas for which it is designed. This range is convertible for use on natural or propane gas. If you decide to use this range on LP gas, conversion must be made by a qualified LP installer before attempting to operate the range on that gas.

For proper operation, the pressure of natural gas supplied to the regulator must be between 4″ and 13″ of water column. For LP gas, the pressure supplied must be between 10″ and 13″ of water column. When checking for proper operation of the regulator, the inlet pressure must be at least 1″ greater than the operating (manifold) pressure as given above. The pressure regulator located at the inlet of the range manifold must remain in the supply line regardless of whether natural or LP gas is being used. A flexible metal appliance connector used to connect the range to the gas supply line should have an I.D. of 1/2″ and be 5 feet in length for ease of installation. In Canada, flexible connectors must be single wall metal connectors no longer than 6 feet in length.

2 CONNECT THE RANGE TO GAS

Gas Pipe and Electric Outlet Locations for Models Equipped with Sealed Burners

This area allows for flush range installation with through-the-wallconnection of pipe stub/shut-off valve and rear wall 120V outlet.

Shortest connection from hard pipe stub location to range hookup.

This area allows for flush range installation with through-the-floor connection of pipe stub/shut-off valve.

Gas Pipe and Electric Outlet Locations for Models Equipped with Standard Twin Burners

Shut off the main gas supply valve before disconnecting the old range and leave it off until new hook-up has been completed. Don’t forget to relight the pilot on other gas appliances when you turn the gas back on.

Because hard piping restricts movement of the range, the use of an A.G.A.-certified flexible metal appliance connector is recommended unless local codes require a hard-piped connection. Never use an old connector when installing a new range. If the hard piping method is used, you must carefully align the pipe; the range cannot be moved after the connection is made.

To prevent gas leaks, use pipe joint compound or wrap Teflon* pipe thread tape around all male (external) pipe threads.

*Teflon: Registered trademark of DuPont

This area allows for flush range installation with

through-the-wall

connection of pipe stub/shut-off valve and rear wall 120V outlet.

Shortest connection from hard pipe stub location to range hookup.

This area allows for flush range installation with through-the-floor connection of pipe stub/shut-off valve.

(continued next page)

31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents RangesXL44 Gas If you received a damaged range… Save time and money. Before you request service…Help US Help YOU… Read this manual carefullyWhen You Get Your Range Important Safety InstructionsUsing Your Range Do not allow anyone to climb, stand or Surface CookingSave These INSTRUCTIONS5 Cleaning Your RangeBaking, Broiling and Roasting Features and appearance vary Features of Your RangeOven Shelves with Stop-Locks Number of shelves varies SeeSurface Burners, Grates and Drip Pans on some models Oven ControlTo Light a Surface Burner Surface CookingSurface Burner Controls Before Lighting a BurnerTop-of-Range Cookware How to Select Flame SizeDo not use a wok on any other support ring Display Clock While Timer Is Operating Clock and TimerTo Set the Timer To Change or Cancel the Timer SettingUsing Your Oven Shelf Positions Oven ShelvesOven Vents Type of Food Shelf Position How to Set Your Range for BakingBaking To avoid possible burns, place the shelvesCookies Pan PlacementPreheating Baking GuidesDon’t Peek PiesCakes Baking PansTo Adjust the Thermostat Adjust the Oven ThermostatType of Margarine Will Affect Baking Performance Use of Aluminum Foil RoastingDual Shelf Cooking Roasting Guide Questions and AnswersFrozen Roasts Broiling Why are my meats not turning out as brown as they should?Should I salt the meat before broiling? Ground Beef Broiling GuideStandard Twin Burners on some models Care and CleaningFor proper ignition Sealed Burner Assemblies on some modelsCooktop Surface Burner GratesOven Bottom Broiler Pan and Grid Oven Light Bulb on some modelsControl Panel and Knobs Removable Broiler Drawer on some modelsRemovable Storage Drawer on some models Oven Air VentsRemovable Kick Panel on some models Outside of door Lift-Off Oven DoorStainless Steel Surfaces on some models For Your Safety Installation InstructionsImportant Safety Instructions General Provide Adequate GAS Supply Connect the Range to GAS Extension Cord Cautions Electrical RequirementsIMPORTANT-Please read carefully Electrical Connections Seal the Openings Yellow flames Electric Ignition ModelsTo remove the oven bottom To remove the broiler drawer Leveling legs can be ⁄ 8 ″ Converting to LP GAS Page Problem Possible Cause QUESTIONS? Before YOU Call for SERVICE…Do It Yourself section We’ll Cover Any Appliance. Anywhere. Anytime Consumer Product Ownership Registration Consumer Support GE Appliances Website Warranty

JGBS02, LGB128 specifications

The GE LGB128 and JGBS02 are two advanced gas turbine models that represent the cutting edge of power generation technology. These turbines are engineered by General Electric, a leader in energy solutions. Both models are designed to enhance efficiency, reduce emissions, and provide reliable power for various applications.

The GE LGB128 is a robust gas turbine characterized by its modular design, which simplifies maintenance and installation processes. This turbine is known for its high efficiency, with a thermal efficiency rating that can reach above 60%. The LGB128 utilizes advanced aerodynamics in its compressor and turbine sections, optimizing performance across a wide range of operating conditions.

One of the key features of the LGB128 is its use of advanced materials and coatings that enhance durability and performance. The turbine blades are crafted from state-of-the-art alloys that can withstand extremely high temperatures, ensuring longevity and reliability. Furthermore, the LGB128 is equipped with sophisticated control systems that leverage machine learning algorithms, enabling real-time optimization of operation and maintenance schedules.

On the other hand, the GE JGBS02 gas turbine is recognized for its versatility and adaptability in various power generation applications. This model is particularly notable for its ability to utilize multiple fuel sources, including natural gas and biogas, which gives it a significant advantage in sustainability. The JGBS02 incorporates advanced combustion technologies that minimize nitrogen oxide (NOx) emissions, making it an environmentally friendly choice for both industrial and utility-scale power generation.

A prominent characteristic of the JGBS02 is its compact design, allowing for flexible installation in limited spaces. This feature is crucial for projects where space is a constraint. Additionally, the turbine is equipped with an intelligent monitoring system that continuously assesses performance metrics, providing operators with valuable insights into efficiency and potential maintenance needs.

Both the LGB128 and JGBS02 are designed to provide reliable performance in today's demanding energy landscape. Their capabilities make them suitable for various applications, including combined cycle power plants and peak shaving operations. As the world pivots toward cleaner energy solutions, these GE turbines embody the technological advancements necessary for fostering a sustainable future in power generation. With their commitment to efficiency, durability, and environmental responsibility, the LGB128 and JGBS02 stand at the forefront of modern energy technology.
Top Page Image Contents