GE XL44 manual When All Hookups Are Completed, Make Sure All Controls Are Left In The Off Position

Page 41

WHEN ALL HOOKUPS ARE COMPLETED:

For cement or concrete construction, you

will need a 1/4″ x 11⁄2″ lag bolt and a 1/2″ O.D. sleeve anchor, which are not provided. Drill the recommended size hole for the hardware.

Install the sleeve anchor into the drilled hole and then install the lag bolt through the device. The bolts must be properly tightened as recommended for the hardware.

Wallboard	Back of
	range

Anti-Tip device

Wood screw

Wallplate

5.Slide the range against the wall, and check for proper installation by grasping the front edge of the cooktop and carefully attempting to tilt the range forward.

WHEN ALL HOOKUPS ARE COMPLETED:

MAKE SURE ALL CONTROLS ARE LEFT IN THE OFF POSITION.

MAKE SURE THE FLOW OF COMBUSTION AND VENTILATION AIR TO THE RANGE IS UNOBSTRUCTED.

CONVERTING TO LP GAS

(or converting back to natural gas from LP)

This range leaves the factory set for use with natural gas. If you want to convert to LP gas, the conversion must be performed by a qualified LP gas installer.

The conversion instructions and LP orifices can be found attached to the range next to the pressure regulator.

Keep these instructions and the orifices in case you want to convert back to natural gas.

41

Image 41

Contents Installation Safety InstructionsCare and Cleaning RangesXL44 GasHELP US HELP YOU… Save time and money. Before you request service…WHAT TO DO IF YOU SMELL GAS Read this manual carefullyImportant Safety Instructions IMPORTANT SAFETY INSTRUCTIONSRead all instructions before using this appliance IMPORTANT SAFETY NOTICESurface Cooking Baking, Broiling and Roasting Cleaning Your RangeSAVE THESE INSTRUCTIONS MASK FOR SHELVES FEATURES OF YOUR RANGEFeatures and appearance vary Oven Light On/Off Switch on some models Features of Your RangeClock and Timer on some models See pageSurface Burner Controls SURFACE COOKINGBefore Lighting a Burner To Light a Surface BurnerDo not use a wok on any other support ring How to Select Flame SizeTop-of-Range Cookware To Set the Timer CLOCK AND TIMERTo Change or Cancel the Timer Setting Display Clock While Timer Is Operatingand Timer USING YOUR OVENUsing Your Oven Before Using Your OvenShelf Positions Oven ShelvesOven Vents locks so when placedBAKING How to Set Your Range for BakingBaking To avoid possible burns, place the shelves in thePreheating Pan PlacementBaking Guides CookiesCakes PiesBaking Pans Don’t PeekThe Type of Margarine Will Affect Baking Performance ADJUST THE OVEN THERMOSTATTo Adjust the Thermostat DO IT YOURSELFRoasting ROASTINGUse of Aluminum Foil Dual Shelf CookingROASTING GUIDE Questions and AnswersFrozen Roasts Q. Why is my roast crumbling when I try toBroiling BROILINGQ. When broiling, is it necessary to always use a grid in the pan? Q. Why are my meats not turning out as brown as they should?The oven and broiler compartment doors must be closed during broiling BROILING GUIDECleaning CARE AND CLEANINGGuide Care and Standard Twin Burners on some modelsFor proper ignition Sealed Burner Assemblies on some modelsGrate Burner cap Drip pan on some models Burner head Electrode ElectrodeBurner Grates Care and CleaningCooktop Surface Oven BottomControl Panel and Knobs Oven Light Bulb on some modelsRemovable Broiler Drawer on some models Broiler Pan and GridOven Air Vents Care and CleaningRemovable Storage Drawer on some models Removable Kick Panel on some modelsTO CLEAN THE DOOR Do not immerse door in water Inside of door Lift-Off Oven DoorCautions about using spray-on oven cleaners Outside of doorStainless Steel Surfaces on some models Special Care of Continuous-Cleaning Oven Interior on some modelsTo Clean the Continuous-Cleaning Oven Do not scrape the porous surface with a knife orFOR YOUR SAFETY INSTALLATION INSTRUCTIONSIn the Commonwealth of Massachusetts BEFORE YOU BEGIN361⁄4″± 1⁄4″ DIMENSIONS AND CLEARANCES36 ″ 40 ″LOCATION IMPORTANT SAFETY INSTRUCTIONSGENERAL KITCHEN CABINETS PROTECT YOUR FLOORTOOLS YOU WILL NEED PREPARATION2 CONNECT THE RANGE TO GAS 1 PROVIDE ADEQUATE GAS SUPPLYGas Pipe and Electric Outlet Locations for Models Equipped with Sealed BurnersConnector Flexible Connector Hookup for Models Equipped with Sealed BurnersAlternate Hookup Rigid Pipe Hookup Options for Models Equipped with Sealed Burners3 ELECTRICAL CONNECTIONS on some models 2 CONNECT THE RANGE TO GAS continuedGrounding CAUTION DO NOT USE A FLAME TO CHECK FOR GAS LEAKS4 SEAL THE OPENINGS Electric Disconnect5 LIGHT THE PILOTS Adjust the Surface Burner Pilots if NecessaryLight the Surface Burner Pilots Light the Oven PilotQuality of Flames 6 CHECK IGNITION OF SURFACE BURNERS7 CHECK IGNITION OF OVEN BURNER A Yellow flamesLoosen Air adjustment shutter Air adjustment shutter LoosenTo remove the oven bottom Oven bottomTo remove the broiler drawer 1. Remove knurled screws holding down rear of oven bottom10 LEVELING THE RANGE 2 1⁄ 8 ″11 INSTALLING THE ANTI-TIP DEVICE CONVERTING TO LP GAS WHEN ALL HOOKUPS ARE COMPLETEDMAKE SURE ALL CONTROLS ARE LEFT IN THE OFF POSITION Page Before You Call for Service QUESTIONS? BEFORE YOU CALL FOR SERVICE…PROBLEM POSSIBLE CAUSEDo It Yourself section BEFORE YOU CALL FOR SERVICE…Warranty Registration Department P.O. Box Louisville, KY GE Service Protection PlusUnlimited service calls All parts and labor costs included We’ll Cover Any Appliance. Anywhere. AnytimeFollow these three steps to protect your new appliance investment online at GEAppliances.comModel Number Serial NumberParts and Accessories Schedule ServiceConsumer Support GE Appliances Websiteunder warranty WARRANTYWHAT IS COVERED WHAT IS NOT COVERED

Related manuals

Manual 56 pages 39.44 Kb