GE XL44 installation instructions Leveling the Range, Installing the ANTI-TIP Device

Page 43

8LEVELING THE RANGE

1.Remove the storage drawer or kick panel.

2. Use a 3/16″ open-end or socket wrench to back out both rear leveling legs approximately two turns.

3. Use a 13⁄8″ open-end or adjustable wrench to back out the front leveling legs two turns.

4. Install the oven shelves in the oven and position the range where it will be installed.

5.Check for levelness by placing a spirit level or a cup, partially filled with water, on one of the oven racks. If using a spirit level, take two readings—with the level placed diagonally first in one direction and then the other.

6.Adjust the leveling legs until the range is level.

7.After the range is level, slide the range

away from the wall so that the Anti-Tip device can be installed.

9 INSTALLING THE ANTI-TIP DEVICE

WARNING:

•Range MUST be secured with an approved Anti-Tip device.

•Unless properly installed, the range could be tipped by you or a child standing, sitting or leaning on an open door.

•After installing the Anti-Tip device, verify that it is in place by carefully attempting to tilt the range forward.

•This range has been designed to meet all recognized industry tip standards for all normal conditions.

•The use of this device does not preclude tipping of the range when not properly installed.

•If the Anti-Tip device supplied with the range does not fit this application, use the universal Anti-Tip device WB02X7909.

1.Mark the wall where the RIGHT EDGE of the range is to be located. Be sure to allow for the countertop overhang if you intend to install the range next to cabinets.

 

Anti-Tip

 

Device

Slotted

 

Head

Wallplate

Screw

Approx. 20°

 

21⁄8″

Marked Edge

of Range

2.Locate the outside edge of the device 21⁄8″ toward the center of the range from the marked edge of the range.

3.Using the device as a template, mark the position of the hole for the screw.

4.For wood construction, drill a pilot hole at an angle of 20 degrees from the horizontal. A nail or awl may be used if a drill is not available.

Mount the Anti-Tip device with the screw provided.

For cement or concrete construction, you will need a 1/4″ x 11⁄2″ lag bolt and a 1/2″ O.D. sleeve anchor, which are not provided. Drill the recommended size hole for the hardware.

Install the sleeve anchor into the drilled hole and then install the lag bolt through the device. The bolts must be properly tightened as recommended for the hardware.

Wallboard

Back of

Range

 

Anti-Tip

Device

Wood Screw

Wallplate

5.Slide the range against the wall, and check for proper installation by grasping the front edge of the cooktop and carefully attempting to tilt the range forward.

WHEN ALL HOOKUPS ARE COMPLETED:

MAKE SURE ALL CONTROLS ARE LEFT IN THE OFF POSITION.

MAKE SURE THE FLOW OF COMBUSTION AND VENTILATION AIR TO THE RANGE IS UNOBSTRUCTED.

43

Page 42 Page 44
Image 43
Page 42 Page 44
Contents Operating Instructions, Tips Safety InstructionsBefore You Call Help US Help YOU… If YOU Need ServiceWhen You Get Your Range Important Safety InstructionsUsing Your Range Always heat fat slowly, and watch as it heats Surface CookingClean only parts listed in this Use and Care Guide Self-Cleaning OvenBaking, Broiling and Roasting Features and appearance may vary Features of Your RangeAnti-Tip Device Feature Index SeeNight Light Switch on some models Oven Vents Cooktop Model and Serial NumbersType of Cooktop Description How it Works Gas Burners HOW does this Cooktop Compare To Your OLD ONE?Surface Cooking Top-of-Range Cookware Appearance may vary Features of Your Oven ControlOven CONTROL, Clock and Timer Using Your Oven Shelves are designed with stop-locks so when Oven VentsOven Shelves Shelf PositionsBaking How to Set Your Range for BakingPreheating Aluminum Foil Pan PlacementBaking Guides CookiesDon’t Peek How to Time BakeHow to Set Immediate Start and Automatic Stop Timed BakingQuick Reminder How to Set Delay Start and Automatic StopDo IT Yourself Adjust the Oven ThermostatUse of Aluminum Foil RoastingDual Shelf Cooking Frozen Roasts Questions and AnswersWhy is my roast crumbling when I try to carve it? Roasting GuideClose the oven door Why are my meats not turning out as brown as they should?Broiling Oven door must be closed during broilingBeef Steaks Broiling GuideBefore a Clean Cycle Operating the SELF-CLEANING OvenTo Stop a Clean Cycle How to Set the Oven for CleaningAfter a Clean Cycle Quick Reminder-Delay Start for Self-Clean How to Delay Start of CleaningWhy do I have ash left in my oven after cleaning? Should there be any odor during the cleaning?Sealed Burner Assemblies on some models Care and CleaningRemove the grates and lift out the drip pans Standard Twin Burners on some modelsTo get rid of burned-on food, place them in a Oven Bottom Burner GratesCooktop Surface Brushed Chrome Cooktop on some modelsOutside of the door Lift-Off Oven DoorBroiler Pan and Grid Inside of the doorControl Panel and Knobs Oven Light Replacement on some modelsRemovable Storage Drawer on some models Removable Kick Panel on some models Oven Air VentsFluorescent Night Light on some models For Your Safety Installation InstructionsImportant Safety Instructions General Connect the Range to GAS Provide Adequate GAS SupplyRigid Pipe Hookup for Models Equipped with Sealed Burners Connect the Range to GASExtension Cord Cautions Electrical Connections on some modelsGrounding Electrical RequirementsElectric Disconnect Electrical ConnectionsQuality of Flames Seal the OpeningsCheck Ignition of Surface Burners Surface Burner IgnitionTo remove the oven bottom Leveling the Range Installing the ANTI-TIP DeviceConvert the Pressure Regulator Converting to LP GAS Sealed Burner models onlyTools Required Prepare Range for ConversionConvert the Oven Burner Orifices Converting Surface BurnersOrifice Spuds for Converting to LP Gas Orifice Spuds for Converting to Natural GasCheck for Leaks Adjust LOW Flame SettingConvert AIR Adjustment Shutter Broil BurnerNAT Converting to LP GAS Standard Twin Burner models onlyTop Burner Orifice Drill Size Color Convert the Oven Burner Orifices Oven BurnerTo convert to LP gas Adjust the Surface Burner Pilots Adjust Oven ThermostatPage Page Problem Possible Cause QUESTIONS? Before YOU Call for SERVICE…Before You Call for Service Oven Door We’ll Be There Warranty
Related manuals
Manual 48 pages 12.36 Kb
Top Page Image Contents