GE JGBP75 manual ⁄ 8 ″

Page 43

9 INSTALLING THE ANTI-TIP DEVICE

WARNING:

•Range MUST be secured with an approved Anti-Tip device.

•Unless properly installed, the range could be tipped by you or a child standing, sitting or leaning on an open door.

•After installing the Anti-Tip device, verify that it is in place by carefully attempting to tilt the range forward.

•This range has been designed to meet all recognized industry tip standards for all normal conditions.

•The use of this device does not preclude tipping of the range when not properly installed.

•If the Anti-Tip device supplied with the range does not fit this application, use the universal Anti-Tip device WB02X7909.

1.Mark the wall where the RIGHT EDGE of the range is to be located. Be sure to allow for the countertop overhang if you intend to install the range next to cabinets.

 

Anti-tip

 

device

Slotted

 

head

Wallplate

screw

Approx. 20°

 

21⁄8″

Marked edge

of range

2.Locate the outside edge of the device 21⁄8″ toward the center of the range from the marked edge of the range.

3.Using the device as a template, mark the position of the hole for the screw.

4.For wood construction, drill a pilot hole at an angle of 20 degrees from the horizontal. A nail or awl may be used if a drill is not available.

Mount the Anti-Tip device with the screw provided.

For cement or concrete construction, you will need a 1/4″ x 11⁄2″ lag bolt and a 1/2″ O.D. sleeve anchor, which are not provided. Drill the recommended size hole for the hardware.

Install the sleeve anchor into the drilled hole and then install the lag bolt through the device. The bolts must be properly tightened as recommended for the hardware.

Wallboard

Back of

range

 

Anti-tip device

Wood screw

Wallplate

5.Slide the range against the wall, and check for proper installation by grasping the front edge of the cooktop and carefully attempting to tilt the range forward.

WHEN ALL HOOKUPS ARE COMPLETED:

MAKE SURE ALL CONTROLS ARE LEFT IN THE OFF POSITION.

MAKE SURE THE FLOW OF COMBUSTION AND VENTILATION AIR TO THE RANGE IS UNOBSTRUCTED.

CONVERTING TO LP GAS

(or converting back to natural gas from LP)

This range leaves the factory set for use with natural gas. If you want to convert to LP gas, the conversion must be performed by a qualified LP gas installer.

The conversion instructions, sticker and LP orifices can be found attached to the range next to the pressure regulator.

There is a second set of instructions included in the envelope containing the product wiring diagrams on the back of the range. Keep these instructions and the orifices in case you want to convert back to natural gas.

43

Page 42 Page 44
Image 43
Page 42 Page 44
Contents Use and Care & Installation Guide Help US Help YOU… If YOU Need ServiceWhen You Get Your Range Important Safety InstructionsUsing Your Range Always heat fat slowly, and watch as it heats Surface CookingClean only parts listed in this Use and Care Guide Self-Cleaning OvenBaking, Broiling and Roasting Features of Your Range Anti-Tip Device Feature Index SeeNight Light Switch on some models Oven Vents Cooktop Model and Serial NumbersType of Cooktop Description How it Works Gas Burners HOW does this Cooktop Compare To Your OLD ONE?Surface Cooking Do not use a wok on any other support ring Top-of-Range CookwareAppearance may vary Features of Your Oven ControlOven CONTROL, Clock and Timer Using Your Oven Shelves are designed with stop-locks so when Oven VentsOven Shelves Shelf PositionsBaking How to Set Your Range for BakingPreheating Aluminum Foil Pan PlacementBaking Guides CookiesDon’t Peek How to Time BakeHow to Set Immediate Start and Automatic Stop Timed BakingQuick Reminder How to Set Delay Start and Automatic StopDo IT Yourself Adjust the Oven ThermostatUse of Aluminum Foil RoastingDual Shelf Cooking Frozen Roasts Questions and AnswersWhy is my roast crumbling when I try to carve it? Roasting GuideClose the oven door Why are my meats not turning out as brown as they should?Broiling Oven door must be closed during broilingBeef Steaks Broiling GuideBefore a Clean Cycle Operating the SELF-CLEANING OvenTo Stop a Clean Cycle How to Set the Oven for CleaningAfter a Clean Cycle Quick Reminder-Delay Start for Self-Clean How to Delay Start of CleaningWhy do I have ash left in my oven after cleaning? Should there be any odor during the cleaning?Sealed Burner Assemblies on some models Care and CleaningRemove the grates and lift out the drip pans Standard Twin Burners on some modelsTo get rid of burned-on food, place them in a Brushed Chrome Cooktop on some models Burner GratesCooktop Surface Oven BottomOutside of the door Lift-Off Oven DoorBroiler Pan and Grid Inside of the doorControl Panel and Knobs Oven Light Replacement on some modelsRemovable Storage Drawer on some models Removable Kick Panel on some models Oven Air VentsFluorescent Night Light on some models For Your Safety Installation InstructionsImportant Safety Instructions General Provide Adequate GAS Supply Connect the Range to GAS Extension Cord Cautions Electrical RequirementsIMPORTANT-Please read carefully Electrical Connections Yellow flames Electric Ignition ModelsTo remove the oven bottom Leveling the Range⁄ 8 ″ Problem Possible Cause QUESTIONS? Before YOU Call for SERVICE…Before You Call for Service Oven Door We’ll Be There Warranty
Top Page Image Contents