GE JGBC20 installation instructions Burner caps

Page 18

Instructions

Care and cleaning of the range.

Burner Caps and Heads (on sealed burners only)

Troubleshooting Tips Installation Instructions Operating Instructions Safety

Use a sewing needle or twist-tie to unclog the small hole in the burner head.

NOTE: Before removing the burner caps and heads, remember their size and location. Replace them in the same location after cleaning.

Burner caps

Lift off when cool. Wash burner caps in hot, soapy water and rinse with clean water. You may scour with a plastic scouring pad to remove burned-on food particles.

Burner heads

For proper ignition, make sure the small hole in the section that fits over the electrode is kept open. A sewing needle or wire twist-tie works well to unclog it.

The slits in the burner heads must be kept clean at all times for an even, unhampered flame.

Clogged or dirty burner ports or electrodes will not allow the burner to operate properly.

Any spill on or around an electrode must be carefully cleaned. Take care to not hit an electrode with anything hard or it could be damaged.

You should clean the burner caps and burner heads routinely, especially after bad spillovers, which could clog the openings in the burner heads. Lift off when cool.

To remove burned-on food, soak the burner heads in a solution of mild liquid detergent and hot water for 20–30 minutes. For more stubborn stains, use a toothbrush.

After cleaning

Before putting the burner caps and heads back, shake out excess water and then dry them thoroughly by setting in a warm oven for 30 minutes.

NOTE: Do not use steel wool or scouring powders to clean the burners.

Replacement

Replace burner heads over the electrodes on the cooktop, in the correct locations according to their size.

Medium head

 

 

 

 

 

 

 

 

 

 

 

Small head

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Front of range

Medium head

Large head

Make sure the slot in the burner head is positioned over the electrode.

Replace the matching size caps onto the heads. There is one small, two medium and one large cap. Sizes are stamped into the bottom of the caps.

Medium cap

 

 

 

 

 

 

 

 

 

 

 

Small cap

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Consumer Support

Front of range

Medium cap

Large cap

Make sure that the heads and caps are replaced in the correct locations.

NOTE: On some models, the burners are all the same size and power.

18

Image 18
Contents Non-Self-Cleaning Gas Write the model and serial numbers here Model # Serial #Consumer Support Troubleshooting ANTI-TIP DeviceImportant Safety Notice Safety Instructions Operating InstructionsOperating Instructions Safety Cook Meat and Poultry THOROUGHLY… Surface Burners Surface Burners Using the gas surface burners Tips Installation Instructions OperatingBefore Lighting a Gas Burner How to Select Flame Size Instructions Troubleshooting TipsTop-of-Range Cookware To Change or Cancel the Kitchen Timer Setting Using the clock and timerTo Set the Kitchen Timer Display Clock While Kitchen Timer Is OperatingOven Control Using the ovenBefore You Begin… Oven VentAluminum Foil How to Set the Oven for Baking or RoastingPreheating and Pan Placement Oven MoistureHow to Set the Oven for Broiling Broiling Guide SuggestionsBroiling Guide CommentsInstructions Troubleshooting Tips Consumer Support Adjust the oven thermostat-Do it yourselfSafety Instructions To Adjust the ThermostatCare and cleaning of the range Tips Installation Instructions Operating InstructionsStandard Twin Burner Assemblies on some models Safety Burner GratesBurner caps Troubleshooting Tips Consumer Support Cooktop SurfaceTo Order Lift-Off Oven Door Consumer Support Troubleshooting TipsTo clean the outside of the door Oven BottomRemovable Broiler Drawer on some models Instructions OperatingBroiler Pan and Grid Oven Air VentsOven Shelves To Clean the Continuous-Cleaning Oven Commonwealth of Massachusetts Before YOU BeginPart Included For Your SafetyTools YOU will Need Materials YOU MAY NeedInstallation Safety Instructions Dimensions and Clearances Location Model and Serial Number LocationConnect the Range to GAS Provide Adequate GAS SupplyInstallation Instructions Alternate Hookup Gas Flow into RangeFlexible Connector Hookup For models equipped with Standard Twin BurnersElectrical Connections Electric Disconnect Seal the OpeningsLight the Pilots Light the Surface Burner PilotsAdjust the Surface Burner Pilots if Necessary Light the Oven PilotCheck Ignition of Oven Burner Electric Ignition Models Check Ignition of Surface BurnersStanding Pilot Models Quality of FlamesRange must be secured with an Install the ANTI-TIP DeviceLevel the Range ⁄ 8 ″Install the ANTI-TIP Device When ALL Hookups are CompletedBefore you call for service… See the Installation of the range section See the Using the clock and timer sectionSee the Care and cleaning of the range section Oven temperaturePopping sound Power outageCrackling or Rainbow effectWe’ll Cover Any Appliance. Anywhere. Anytime Consumer Product Ownership Registration Accessories Looking For Something More?GE Will Replace What GE Will Not CoverSafety Instructions Operating Camco Will ReplaceWhat Camco Will Not Cover Consumer Support GE Appliances Website Schedule ServiceParts and Accessories Real Life Design Studio