Maytag W10258096A Verify Anti-Tip Bracket Location, Level Range, Complete connection

Page 10

3.Use a ¹⁵⁄₁₆" combination wrench and an adjustable wrench to attach the flexible connector to the adapters. Check that connector is not kinked.

If burner caps are not properly positioned, surface burners will not light. Place burner grates over burners and caps.

A

B C

A. Gas pressure regulator

B.Use pipe-joint compound.

C.Adapter (must have ½" male pipe thread)

D.Flexible connector

D

E

H GF

E. Manual gas shutoff valve F. ½" or ¾" gas pipe

G. Use pipe-joint compound. H. Adapter

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

4.Gas supply pipe must not be more than 10" (25.4 cm) above the floor.

E

A

B

CD

A. Gas pressure regulator

B.Adapter

C.Flexible connector

D.Manual shutoff valve

E.10" (25.4 cm) max. straight pipe

Complete connection

1.Open the manual shutoff valve in the gas supply line. The valve is open when the handle is parallel to the gas pipe.

A

B

A. Closed valve

B. Open valve

2.Test all connections by brushing on an approved noncorrosive leak-detection solution. If bubbles appear, a leak is indicated. Correct any leak found.

3.Remove cooktop burner caps and grates from parts package. Align recess in burner caps with pins in burner base. Burner caps should be level when properly positioned.

fire, or electrical shock.

4.Plug into a grounded 3 prong outlet.

Verify Anti-Tip Bracket Location

1.Move range close to cabinet opening.

2.Remove cardboard or hardboard from under the range. Using 2 or more people, gently move range into its final location.

3.Pull storage drawer out completely.

4.To check that the anti-tip bracket is installed, use a flashlight and look underneath the bottom of the range.

Look for the anti-tip bracket securely attached to floor or wall.

Slide range back so rear range foot is under anti-tip bracket.

Level Range

1.Place oven rack in oven.

2.Place level on oven rack and check levelness of range, first side to side; then front to back.

3.If range is not level, pull range forward until rear leveling leg is removed from the anti-tip bracket.

4.Use wrench to adjust leveling legs up or down until range is level. Push range back into position.

5.Check that rear leveling leg is engaged in anti-tip bracket.

NOTE: Range must be level for satisfactory baking performance.

10

Image 10
Contents Instructions D’INSTALLATION DES Cuisinières À GAZ Autoportantes DE 30 76,2 CMRange Safety Your safety and the safety of others are very importantPage Tools and Parts Installation RequirementsLocation Requirements Product Dimensions Cabinet Dimensions Type of Gas Electrical RequirementsGas Supply Requirements Natural gasGas Pressure Regulator Gas Supply Pressure TestingGas Supply Line Burner Input RequirementsAdjust Leveling Legs Installation InstructionsUnpack Range Typical flexible connection Install Anti-Tip BracketMake Gas Connection Floor MountingComplete connection Verify Anti-Tip Bracket LocationLevel Range Plug into a grounded 3 prong outletElectronic Ignition System Complete Installation Replace Oven Racks and Storage DrawerLP Gas Conversion GAS ConversionsTo Convert Gas Pressure Regulator To Convert Oven Broil Burner Reinstall the oven bake burner coverTo Convert Oven Bake Burner Unscrew the regulator cap and remove the plastic coverLP Gas Orifice Spud Chart Burner Rating Color Size ID Number To Convert Surface BurnersNatural Gas Conversion Locate the oven orifice hood from the front of the range Gas tube opening Burner base Page Sécurité DE LA Cuisinière Votre sécurité et celle des autres est très importanteAvertissement Exigences demplacement Exigences D’INSTALLATIONOutillage et pièces Dimensions du produit Dimensions du placardType de gaz Spécifications électriquesSpécifications de l’alimentation en gaz Gaz naturelDébit thermique des brûleurs Canalisation de gazDétendeur Tests de pressurisation de la canalisation de gazDéballage de la cuisinière Instructions DinstallationRéglage des pieds de nivellement Raccordement typique par raccord flexible Installation de la bride antibasculementRaccordement au gaz Montage au plancherVérification de lemplacement de la bride Antibasculement Terminer le raccordementAllumage initial et réglages des flammes Réglage de laplomb de la cuisinièreSystème dallumage électronique Si les brûleurs ne sallument pas correctementContrôle du fonctionnement du brûleur du gril Appuyer sur Cancel annulation après avoir terminéContrôle du fonctionnement du brûleur de cuisson au four Ôter la grille du fourRéinstallation du tiroir de remisage Réinstallation des grilles de four et du tiroir De remisageAchever l’installation Si vous avez besoin dassistance ou de serviceConversion de Gaz naturel à Propane Conversions Pour Changement DE GAZConversion du détendeur Conversion du brûleur de cuisson au four Injecteur femelle pour gaz propane numéroConversion du brûleur du gril Conversion des brûleurs de surfaceConversion pour lalimentation au gaz Naturel De côté Soulever et enlever le couvercle du brûleur de cuisson auFour Soulever de l’orifice du four et le mettre de côtéConversion du brûleur du gril Ouverture du tube Base du brûleur ’arrivée de gaz Page W10258096A

W10258096A specifications

The Maytag W10258096A is a high-quality appliance part designed specifically for Maytag washing machines. This vital component serves as a replacement for worn-out or damaged parts, ensuring the longevity and efficiency of your laundry appliance. As a reputable brand in the home appliance industry, Maytag is known for its commitment to durability and performance, and the W10258096A is no exception.

One of the main features of the Maytag W10258096A is its compatibility with a range of Maytag washing machine models. This versatility makes it a convenient choice for many consumers, as it can effectively replace various parts across different units. This is particularly beneficial for households with older machines that may require updated components to maintain functionality.

In terms of technology, the W10258096A is engineered with precision to ensure seamless integration with existing washing machine systems. It features high-grade materials that contribute to its resilience against wear and tear. This robust construction not only enhances the part's durability but also improves the overall performance of the washing machine, allowing it to operate at optimal efficiency.

Another characteristic of the Maytag W10258096A is its user-friendly installation process. Designed with the average homeowner in mind, this component allows for easy replacement without the need for extensive technical knowledge. Clear instructions accompany the part, helping users to complete the installation efficiently.

Moreover, the W10258096A is backed by Maytag’s reputation for quality service and support, which gives consumers peace of mind. Whether you're dealing with water leaks, drainage issues, or other common washing machine problems, this part can address those challenges effectively, restoring your machine to its full capability.

Overall, the Maytag W10258096A stands out as a reliable replacement part that embodies the values of quality, efficiency, and ease of use that Maytag is known for. This replacement component not only extends the life of your washing machine but also promotes better cleaning performance, making laundry day a much smoother experience. When maintenance needs arise, choosing the W10258096A is a practical decision for any Maytag appliance owner looking to keep their machine in top shape.