Maytag W10258096A Installation Requirements, Tools and Parts, Location Requirements

Page 4

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

Location Requirements

IMPORTANT: Observe all governing codes and ordinances. Do not obstruct flow of combustion and ventilation air.

■ It is the installer’s responsibility to comply with installation

Tools needed

■Tape measure

■Phillips screwdriver

■Flat-blade screwdriver

■¹⁄₈" flat-blade screwdriver

■Level

■Drill

■Wrench or pliers

■Pipe wrench

■¹⁵⁄₁₆" combination wrench

■¹⁄₈" (3.2 mm) drill bit (for wood floors)

■Marker or pencil

■Pipe-joint compound resistant to LP gas

■³⁄₁₆" (4.8 mm) carbide-tipped masonry drill bit (for concrete/ceramic floors)

■Noncorrosive leak-detection solution

For LP/Natural Gas

Conversions

■½" combination wrench

■⁹⁄₃₂" (7.0 mm) nut driver

■Masking tape

clearances specified on the model/serial rating plate. The

model/serial rating plate is located behind the storage drawer

on the right-hand side of the oven frame.

■ The range should be located for convenient use in the

kitchen.

■ Recessed installations must provide complete enclosure of

the sides and rear of the range.

■ To eliminate the risk of burns or fire by reaching over heated

surface units, cabinet storage space located above the

surface units should be avoided. If cabinet storage is to be

provided, the risk can be reduced by installing a range hood

or microwave hood combination that projects horizontally a

minimum of 5" (12.7 cm) beyond the bottom of the cabinets.

■ All openings in the wall or floor where range is to be installed

must be sealed.

■ Cabinet opening dimensions that are shown must be used.

Given dimensions are minimum clearances.

Parts supplied

Check that all parts are included.

■LP/Natural Gas Conversion Kit (taped near left rear leg, inside storage drawer compartment)

■2 - Burner grates

■5 - Burner caps

■2 - Oven racks (3 on some models)

■2 - #12 x 1⁵⁄₈" screws (for mounting anti-tip bracket)

■Anti-tip bracket (taped inside storage drawer)

Anti-tip bracket must be securely mounted to the back wall or floor. Thickness of flooring may require longer screws to anchor bracket to subfloor. Longer screws are available from your local hardware store.

Parts needed

Check local codes and consult gas supplier. Check existing gas supply and electrical supply. See “Electrical Requirements” and “Gas Supply Requirements” sections.

■ The floor anti-tip bracket must be installed. To install the anti-

tip bracket shipped with the range, see “Install Anti-Tip

Bracket” section.

■ Grounded electrical supply is required. See “Electrical

Requirements” section.

■ Proper gas supply connection must be available. See “Gas

Supply Requirements” section.

■ Contact a qualified floor covering installer to check that the

floor covering can withstand at least 200°F (93°C).

■ Use an insulated pad or ¼" (0.64 cm) plywood under range if

installing range over carpeting.

IMPORTANT: To avoid damage to your cabinets, check with your builder or cabinet supplier to make sure that the materials used will not discolor, delaminate or sustain other damage. This oven has been designed in accordance with the requirements of UL and CSA International and complies with the maximum allowable wood cabinet temperatures of 194° (90°C).

Mobile Home - Additional Installation Requirements

The installation of this range must conform to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280). When such standard is not applicable, use the Standard for Manufactured Home Installations, ANSI A225.1/NFPA 501A or with local codes.

In Canada, the installation of this range must conform with the current standards CAN/CSA-A240-latest edition, or with local codes.

Mobile home installations require:

■When this range is installed in a mobile home, it must be secured to the floor during transit. Any method of securing the range is adequate as long as it conforms to the standards listed above.

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Instructions D’INSTALLATION DES Cuisinières À GAZ Autoportantes DE 30 76,2 CMRange Safety Your safety and the safety of others are very importantPage Tools and Parts Installation RequirementsLocation Requirements Product Dimensions Cabinet Dimensions Electrical Requirements Gas Supply RequirementsType of Gas Natural gasGas Supply Pressure Testing Gas Supply LineGas Pressure Regulator Burner Input RequirementsAdjust Leveling Legs Installation InstructionsUnpack Range Install Anti-Tip Bracket Make Gas ConnectionTypical flexible connection Floor MountingVerify Anti-Tip Bracket Location Level RangeComplete connection Plug into a grounded 3 prong outletElectronic Ignition System Complete Installation Replace Oven Racks and Storage DrawerLP Gas Conversion GAS ConversionsTo Convert Gas Pressure Regulator Reinstall the oven bake burner cover To Convert Oven Bake BurnerTo Convert Oven Broil Burner Unscrew the regulator cap and remove the plastic coverLP Gas Orifice Spud Chart Burner Rating Color Size ID Number To Convert Surface BurnersNatural Gas Conversion Locate the oven orifice hood from the front of the range Gas tube opening Burner base Page Sécurité DE LA Cuisinière Votre sécurité et celle des autres est très importanteAvertissement Exigences demplacement Exigences D’INSTALLATIONOutillage et pièces Dimensions du produit Dimensions du placardSpécifications électriques Spécifications de l’alimentation en gazType de gaz Gaz naturelCanalisation de gaz DétendeurDébit thermique des brûleurs Tests de pressurisation de la canalisation de gazDéballage de la cuisinière Instructions DinstallationRéglage des pieds de nivellement Installation de la bride antibasculement Raccordement au gazRaccordement typique par raccord flexible Montage au plancherVérification de lemplacement de la bride Antibasculement Terminer le raccordementRéglage de laplomb de la cuisinière Système dallumage électroniqueAllumage initial et réglages des flammes Si les brûleurs ne sallument pas correctementAppuyer sur Cancel annulation après avoir terminé Contrôle du fonctionnement du brûleur de cuisson au fourContrôle du fonctionnement du brûleur du gril Ôter la grille du fourRéinstallation des grilles de four et du tiroir De remisage Achever l’installationRéinstallation du tiroir de remisage Si vous avez besoin dassistance ou de serviceConversion de Gaz naturel à Propane Conversions Pour Changement DE GAZConversion du détendeur Conversion du brûleur de cuisson au four Injecteur femelle pour gaz propane numéroConversion du brûleur du gril Conversion des brûleurs de surfaceConversion pour lalimentation au gaz Naturel Soulever et enlever le couvercle du brûleur de cuisson au FourDe côté Soulever de l’orifice du four et le mettre de côtéConversion du brûleur du gril Ouverture du tube Base du brûleur ’arrivée de gaz Page W10258096A

W10258096A specifications

The Maytag W10258096A is a high-quality appliance part designed specifically for Maytag washing machines. This vital component serves as a replacement for worn-out or damaged parts, ensuring the longevity and efficiency of your laundry appliance. As a reputable brand in the home appliance industry, Maytag is known for its commitment to durability and performance, and the W10258096A is no exception.

One of the main features of the Maytag W10258096A is its compatibility with a range of Maytag washing machine models. This versatility makes it a convenient choice for many consumers, as it can effectively replace various parts across different units. This is particularly beneficial for households with older machines that may require updated components to maintain functionality.

In terms of technology, the W10258096A is engineered with precision to ensure seamless integration with existing washing machine systems. It features high-grade materials that contribute to its resilience against wear and tear. This robust construction not only enhances the part's durability but also improves the overall performance of the washing machine, allowing it to operate at optimal efficiency.

Another characteristic of the Maytag W10258096A is its user-friendly installation process. Designed with the average homeowner in mind, this component allows for easy replacement without the need for extensive technical knowledge. Clear instructions accompany the part, helping users to complete the installation efficiently.

Moreover, the W10258096A is backed by Maytag’s reputation for quality service and support, which gives consumers peace of mind. Whether you're dealing with water leaks, drainage issues, or other common washing machine problems, this part can address those challenges effectively, restoring your machine to its full capability.

Overall, the Maytag W10258096A stands out as a reliable replacement part that embodies the values of quality, efficiency, and ease of use that Maytag is known for. This replacement component not only extends the life of your washing machine but also promotes better cleaning performance, making laundry day a much smoother experience. When maintenance needs arise, choosing the W10258096A is a practical decision for any Maytag appliance owner looking to keep their machine in top shape.
Top Page Image Contents