Maytag W10258096A installation instructions Electronic Ignition System

Page 11

Electronic Ignition System

Initial lighting and gas flame adjustments

Cooktop and oven burners use pilotless igniters in place of standing pilots. When the cooktop control knob is turned to the “LITE” position, the system creates a spark to light the burner. This sparking continues, as long as the control knob is turned to “LITE.”

When the oven control is turned to the desired setting, a glow bar igniter heats and ignites the gas.

Check Operation of Cooktop Burners

Standard Surface Burners

Push in and turn each control knob to the “LITE” position.

The flame should light within 4 seconds. The first time a burner is lit it may take longer than 4 seconds to light because of air in the gas line.

If burners do not light properly:

Turn cooktop control knob to the “OFF” position.

Check that the range is plugged in and the circuit breaker has not tripped or the household fuse has not blown.

Check that the gas shutoff valves are set to the “open” position.

Check that burner caps are properly positioned on burner bases.

Repeat start-up. If a burner does not light at this point, turn the control knobs to “Off” and contact your dealer or authorized service company for assistance.

Adjust Flame Height

Adjust the height of top burner flames. The cooktop “low” burner flame should be a steady blue flame approximately ¼" (0.64 cm) high.

A

B

A.Low flame

B.High flame

To adjust standard burners:

The flame can be adjusted using the adjustment screw in the center of the valve stem. The valve stem is located directly underneath the control knob.

If the “low” flame needs to be adjusted:

1.Light 1 burner and turn to lowest setting.

2.Remove the control knob.

Hold the knob stem in the low position using a pair of pliers. Use an ¹⁄₈" (3.0 mm) flat-blade screwdriver to turn the screw located in the center of the control knob stem until the flame is the proper size.

3.Replace the control knob.

4.Test the flame by turning the control from “LO” to “HI,” checking the flame at each setting.

5.Repeat above steps for each burner.

Check Operation of Oven Bake Burner

1.Remove the oven rack.

2.Using a Phillips screwdriver, remove the 2 bake burner cover screws.

3.Lift up on rear of bake burner cover and remove.

4.Place cover on a covered surface.

A

B

A. Bake burner cover

B. Bake burner cover screws

5.Press BAKE.

6.Press START.

The igniter used to light the bake burner will glow. Once the igniter is hot the oven bake burner should light. Under certain conditions it may take up to 60 seconds for it to light.

Adjust Oven Bake Burner Flame (if needed)

1.Remove storage drawer.

2.Check the oven bake burner for proper flame.

This flame should have a ½" (1.3 cm) long inner cone of bluish-green, with an outer mantle of dark blue, and should be clean and soft in character. No yellow tips, blowing or lifting of flame should occur.

11

Image 11
Contents Autoportantes DE 30 76,2 CM Instructions D’INSTALLATION DES Cuisinières À GAZYour safety and the safety of others are very important Range SafetyPage Location Requirements Installation RequirementsTools and Parts Product Dimensions Cabinet Dimensions Natural gas Electrical RequirementsGas Supply Requirements Type of GasBurner Input Requirements Gas Supply Pressure TestingGas Supply Line Gas Pressure RegulatorUnpack Range Installation InstructionsAdjust Leveling Legs Floor Mounting Install Anti-Tip BracketMake Gas Connection Typical flexible connectionPlug into a grounded 3 prong outlet Verify Anti-Tip Bracket LocationLevel Range Complete connectionElectronic Ignition System Replace Oven Racks and Storage Drawer Complete InstallationTo Convert Gas Pressure Regulator GAS ConversionsLP Gas Conversion Unscrew the regulator cap and remove the plastic cover Reinstall the oven bake burner coverTo Convert Oven Bake Burner To Convert Oven Broil BurnerTo Convert Surface Burners LP Gas Orifice Spud Chart Burner Rating Color Size ID NumberNatural Gas Conversion Locate the oven orifice hood from the front of the range Gas tube opening Burner base Page Votre sécurité et celle des autres est très importante Sécurité DE LA CuisinièreAvertissement Outillage et pièces Exigences D’INSTALLATIONExigences demplacement Dimensions du placard Dimensions du produitGaz naturel Spécifications électriquesSpécifications de l’alimentation en gaz Type de gazTests de pressurisation de la canalisation de gaz Canalisation de gazDétendeur Débit thermique des brûleursRéglage des pieds de nivellement Instructions DinstallationDéballage de la cuisinière Montage au plancher Installation de la bride antibasculementRaccordement au gaz Raccordement typique par raccord flexibleTerminer le raccordement Vérification de lemplacement de la bride AntibasculementSi les brûleurs ne sallument pas correctement Réglage de laplomb de la cuisinièreSystème dallumage électronique Allumage initial et réglages des flammesÔter la grille du four Appuyer sur Cancel annulation après avoir terminéContrôle du fonctionnement du brûleur de cuisson au four Contrôle du fonctionnement du brûleur du grilSi vous avez besoin dassistance ou de service Réinstallation des grilles de four et du tiroir De remisageAchever l’installation Réinstallation du tiroir de remisageConversion du détendeur Conversions Pour Changement DE GAZConversion de Gaz naturel à Propane Injecteur femelle pour gaz propane numéro Conversion du brûleur de cuisson au fourConversion des brûleurs de surface Conversion du brûleur du grilConversion pour lalimentation au gaz Naturel Soulever de l’orifice du four et le mettre de côté Soulever et enlever le couvercle du brûleur de cuisson auFour De côtéConversion du brûleur du gril Ouverture du tube Base du brûleur ’arrivée de gaz Page W10258096A

W10258096A specifications

The Maytag W10258096A is a high-quality appliance part designed specifically for Maytag washing machines. This vital component serves as a replacement for worn-out or damaged parts, ensuring the longevity and efficiency of your laundry appliance. As a reputable brand in the home appliance industry, Maytag is known for its commitment to durability and performance, and the W10258096A is no exception.

One of the main features of the Maytag W10258096A is its compatibility with a range of Maytag washing machine models. This versatility makes it a convenient choice for many consumers, as it can effectively replace various parts across different units. This is particularly beneficial for households with older machines that may require updated components to maintain functionality.

In terms of technology, the W10258096A is engineered with precision to ensure seamless integration with existing washing machine systems. It features high-grade materials that contribute to its resilience against wear and tear. This robust construction not only enhances the part's durability but also improves the overall performance of the washing machine, allowing it to operate at optimal efficiency.

Another characteristic of the Maytag W10258096A is its user-friendly installation process. Designed with the average homeowner in mind, this component allows for easy replacement without the need for extensive technical knowledge. Clear instructions accompany the part, helping users to complete the installation efficiently.

Moreover, the W10258096A is backed by Maytag’s reputation for quality service and support, which gives consumers peace of mind. Whether you're dealing with water leaks, drainage issues, or other common washing machine problems, this part can address those challenges effectively, restoring your machine to its full capability.

Overall, the Maytag W10258096A stands out as a reliable replacement part that embodies the values of quality, efficiency, and ease of use that Maytag is known for. This replacement component not only extends the life of your washing machine but also promotes better cleaning performance, making laundry day a much smoother experience. When maintenance needs arise, choosing the W10258096A is a practical decision for any Maytag appliance owner looking to keep their machine in top shape.