Maytag W10258096A Gas Supply Line, Gas Pressure Regulator, Burner Input Requirements

Page 7

Gas Supply Line

Provide a gas supply line of ¾" (1.9 cm) rigid pipe to the range location. A smaller size pipe on longer runs may result in insufficient gas supply. With LP gas, piping or tubing size can be ½" (1.3 cm) minimum. Usually, LP gas suppliers determine the size and materials used in the system.

NOTE: Pipe-joint compounds that resist the action of LP gas must be used. Do not use TEFLON®† tape.

Flexible metal appliance connector:

If local codes permit, a new CSA design-certified, 4 to 5 ft (122 to 152.4 cm) long, ½" (1.3 cm) or

¾" (1.9 cm) I.D., flexible metal appliance connector may be used for connecting range to the gas supply line.

Gas Pressure Regulator

The gas pressure regulator supplied with this range must be used. The inlet pressure to the regulator should be as follows for proper operation:

Natural gas:

Minimum pressure: 5" WCP

Maximum pressure: 14" WCP

LP gas:

Minimum pressure: 11" WCP

Maximum pressure: 14" WCP

Contact local gas supplier if you are not sure about the inlet pressure.

A ½" (1.3 cm) male pipe thread is needed for connection to the female pipe threads of the inlet to the appliance pressure regulator.

Do not kink or damage the flexible metal tubing when moving the range.

Rigid pipe connection:

The rigid pipe connection requires a combination of pipe fittings to obtain an in-line connection to the range. The rigid pipe must be level with the range connection. All strains must be removed from the supply and fuel lines so range will be level and in line.

Must include a shutoff valve:

The supply line must be equipped with a manual shutoff valve. This valve should be located in the same room but external to the range opening, such as an adjacent cabinet. It should be in a location that allows ease of opening and closing. Do not block access to shutoff valve. The valve is for turning on or shutting off gas to the range.

B

A

C

A. Gas supply line

B. Shutoff valve “open” position

C. To range

†®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.

Burner Input Requirements

Input ratings shown on the model/serial rating plate are for elevations up to 2,000 ft (609.6 m).

For elevations above 2,000 ft (609.6 m), ratings are reduced at a rate of 4% for each 1,000 ft (304.8 m) above sea level (not applicable for Canada).

Gas Supply Pressure Testing

Gas supply pressure for testing regulator must be at least

1" water column pressure above the manifold pressure shown on the model/serial rating plate.

Line pressure testing above ½ psi gauge (14" WCP)

The range and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of ½ psi (3.5 kPa).

Line pressure testing at ½ psi gauge (14" WCP) or lower

The range must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than ½ psi (3.5 kPa).

7

Image 7
Contents Autoportantes DE 30 76,2 CM Instructions D’INSTALLATION DES Cuisinières À GAZYour safety and the safety of others are very important Range SafetyPage Tools and Parts Installation RequirementsLocation Requirements Product Dimensions Cabinet Dimensions Natural gas Electrical RequirementsGas Supply Requirements Type of GasBurner Input Requirements Gas Supply Pressure TestingGas Supply Line Gas Pressure RegulatorAdjust Leveling Legs Installation InstructionsUnpack Range Floor Mounting Install Anti-Tip BracketMake Gas Connection Typical flexible connectionPlug into a grounded 3 prong outlet Verify Anti-Tip Bracket LocationLevel Range Complete connectionElectronic Ignition System Replace Oven Racks and Storage Drawer Complete InstallationLP Gas Conversion GAS ConversionsTo Convert Gas Pressure Regulator Unscrew the regulator cap and remove the plastic cover Reinstall the oven bake burner coverTo Convert Oven Bake Burner To Convert Oven Broil BurnerTo Convert Surface Burners LP Gas Orifice Spud Chart Burner Rating Color Size ID NumberNatural Gas Conversion Locate the oven orifice hood from the front of the range Gas tube opening Burner base Page Votre sécurité et celle des autres est très importante Sécurité DE LA CuisinièreAvertissement Exigences demplacement Exigences D’INSTALLATIONOutillage et pièces Dimensions du placard Dimensions du produitGaz naturel Spécifications électriquesSpécifications de l’alimentation en gaz Type de gazTests de pressurisation de la canalisation de gaz Canalisation de gazDétendeur Débit thermique des brûleursDéballage de la cuisinière Instructions DinstallationRéglage des pieds de nivellement Montage au plancher Installation de la bride antibasculementRaccordement au gaz Raccordement typique par raccord flexibleTerminer le raccordement Vérification de lemplacement de la bride AntibasculementSi les brûleurs ne sallument pas correctement Réglage de laplomb de la cuisinièreSystème dallumage électronique Allumage initial et réglages des flammesÔter la grille du four Appuyer sur Cancel annulation après avoir terminéContrôle du fonctionnement du brûleur de cuisson au four Contrôle du fonctionnement du brûleur du grilSi vous avez besoin dassistance ou de service Réinstallation des grilles de four et du tiroir De remisageAchever l’installation Réinstallation du tiroir de remisageConversion de Gaz naturel à Propane Conversions Pour Changement DE GAZConversion du détendeur Injecteur femelle pour gaz propane numéro Conversion du brûleur de cuisson au fourConversion des brûleurs de surface Conversion du brûleur du grilConversion pour lalimentation au gaz Naturel Soulever de l’orifice du four et le mettre de côté Soulever et enlever le couvercle du brûleur de cuisson auFour De côtéConversion du brûleur du gril Ouverture du tube Base du brûleur ’arrivée de gaz Page W10258096A

W10258096A specifications

The Maytag W10258096A is a high-quality appliance part designed specifically for Maytag washing machines. This vital component serves as a replacement for worn-out or damaged parts, ensuring the longevity and efficiency of your laundry appliance. As a reputable brand in the home appliance industry, Maytag is known for its commitment to durability and performance, and the W10258096A is no exception.

One of the main features of the Maytag W10258096A is its compatibility with a range of Maytag washing machine models. This versatility makes it a convenient choice for many consumers, as it can effectively replace various parts across different units. This is particularly beneficial for households with older machines that may require updated components to maintain functionality.

In terms of technology, the W10258096A is engineered with precision to ensure seamless integration with existing washing machine systems. It features high-grade materials that contribute to its resilience against wear and tear. This robust construction not only enhances the part's durability but also improves the overall performance of the washing machine, allowing it to operate at optimal efficiency.

Another characteristic of the Maytag W10258096A is its user-friendly installation process. Designed with the average homeowner in mind, this component allows for easy replacement without the need for extensive technical knowledge. Clear instructions accompany the part, helping users to complete the installation efficiently.

Moreover, the W10258096A is backed by Maytag’s reputation for quality service and support, which gives consumers peace of mind. Whether you're dealing with water leaks, drainage issues, or other common washing machine problems, this part can address those challenges effectively, restoring your machine to its full capability.

Overall, the Maytag W10258096A stands out as a reliable replacement part that embodies the values of quality, efficiency, and ease of use that Maytag is known for. This replacement component not only extends the life of your washing machine but also promotes better cleaning performance, making laundry day a much smoother experience. When maintenance needs arise, choosing the W10258096A is a practical decision for any Maytag appliance owner looking to keep their machine in top shape.