Amana ARR3100*, ARR3400*, ARR3601* owner manual Converting 3-Wire to 4-Wire Power Cord, Level Range

Page 9

7.Attach power lead, red wire or black wire to right terminal. Secure with hex nuts provided.

Wires from range

(Number of wires on each terminal can vary)

 

A

 

 

 

 

 

B

 

 

 

A

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Converting 3-Wire to 4-Wire Power Cord

1.Remove rear wire cover.

2.Remove bottom cord clamp screw and retain for further use.

3.Remove screw/hex nuts from terminal block and retain for further use.

4.Remove all 3-wire or cable leads from the terminal block and proceed to remove the power cord from the range by pulling in a downward motion so the cord is removed from strain relief.

5.To install the 4-wire cord, please follow step 3 through step 9 of Installing 4-Wire Power Cord section.

Level Range

Wires from power cord

A—240 or 208 power lead terminal (Connect black or red insulated wire and secure with brass nut.)

B—Neutral terminal (Connect insulated white insulated wire and secure with brass nut.)

Attach Power Leads

7.Position grounding strap down and away from terminal block. Attach green or bare wire and grounding strap to back of range using green ground screw previously removed in step 3.

Wires from range

(Number of wires on each terminal can vary)

A

Wires from power cord

A—Ground screw (Connect green insulated wire and secure with screw.)

Attach Green or Bare Wire and Grounding Strap

8.Firmly tighten all connections to ensure proper electrical connection.

9.Place screw through strain relief, tighten, and replace rear wire cover.

!CAUTION

To avoid damaging oven door, do not lift or move range by oven door handle. Glass can break.

Carefully level range using legs provided. Range must be level to cook and bake uniformly.

•Place a level on top oven rack or on range top when leveling.

•Leveling legs must extended ¼ inch to engage anti-tip bracket.

Removal and Replacement of Range

1.Disconnect power to range.

2.Slide range forward.

3.Unplug range cord and place range aside.

4.Remove anti-tip bracket.

5.Install anti-tip bracket into new location using instructions provided with bracket or see Anti-tip Bracket Installation section in this manual.

6.To reinstall range, follow instructions in Installation section of this manual.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Installer Please Read Manual Before Operating RangeCustomer Contents Important Safety Information Case of Fire PrecautionsSurface Element Fire Oven FiresPacking Material InstallationRange Location Cabinet OpeningPower Supply Location Anti-tip Bracket InstallationIrregular Cabinet and Countertop Heights Line Voltage RequirementsNeutral terminal connect wire Power Cord RequirementsPower terminals Range Terminal BlockInstalling 4-Wire Power Cord Installing 3-Wire Power CordConverting 3-Wire to 4-Wire Power Cord Removal and Replacement of RangeLevel Range Operation Range FeaturesSetting Electronic Clock Electronic Clock and Timer Some ModelsSetting Electronic Timer Canceling Electronic TimerOperating Surface Elements SettingsOven Rack Placement Prepare to BakeRemove Items Stored in Oven Broiling BakingPreheating Broiling TipsCooking Guide Food Oven Temperature Cooking TimeBaking Guide Poultry Roasting GuideBeef and Pork Roasting Guide Broiling GuideFood Thickness Rack position Cooking time Removing Oven Door Care and CleaningRemoving Panel Some Models Replacing Oven Light Some ModelsCleaning Part Materials to Use General Directions Before Calling for Service ProblemCheck Cooking Products excluding wall ovens Warranty
Top Page Image Contents