Verona VEFSGG 365 ND warranty Electrical Grounding Instructions, Replacement Parts

Page 5

GENERAL INFORMATION

1.Installation must conform with local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1-Latest Edition.

2.Installation in manufactured (mobile) home: installation must conform with the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 [formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD (Part 280)] or, when such standard is not applicable, the Standard for Manufactured Home Installations, ANSI/NCSBCS A225.1, or with local codes where applicable.

3.Installation in Recreational Park Trailers: installation must conform with state or other codes or, in the absence of such codes, with the Standard for Recreational Park Trailers, ANSI A119.5.

4. WARNING!!

This appliance shall not be used for space heating. This information is based on safety considerations.

5.AlI openings in the wall behind the appliance and in the floor under the appliance shall be sealed.

6.Keep appliance area clear and free from combustible materials, gasoline, and other flammable vapors.

7.Do not obstruct the flow of combustion and ventilation air.

8.Disconnect the electrical supply to the appliance before servicing.

9.When removing appliance for cleaning and/or service;

A.Shut off gas at main supply.

B.Disconnect AC power supply.

C.Disconnect gas line to the inlet pipe.

D.Carefully remove the range by pulling outward. CAUTION: Range is heavy; use care in handling.

10.Electrical Requirement

Electrical installation should comply with national and local codes.

11.Air Supply and Ventilation

The installer must refers to local/national codes.

12.Gas Manifold Pressure

Natural gas - 4.0” W.C.P. LP/Propane - 11.0” W.C.P.

WARNING!!

ELECTRICAL GROUNDING INSTRUCTIONS

The range must be electrically grounded in accordance with local codes or, in the absence of local codes, with the National Electrical Code, ANSI/NFPA No. 70-latest edition. Installation should be made by a Iicensed electrician.

FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED.

If an external electrical source is utilized, the installation must be electrically grounded in accordance with local codes or, in the absence of local codes, with the national Electrical Code, ANSI/NFPA 70.

This appliance is equipped with a three-prong grounding plug for your protection against shock hazard and should be plugged directly into a properly grounded socket.

Do not under any circumstances cut or remove the third (ground) prong from the power plug.

REPLACEMENT PARTS

Only authorized replacement parts may be used in performing service on the range. Replacement parts are available from factory authorized parts distributors. Contact the nearest parts distributor in your area.

13.The misuse of oven door (e.g. stepping, sitting, or leaning on them) can result in potential hazards and/or injuries.

14.When installing or removing the range for service, a rolling lift jack should be used. Do not push against any of the edges of the range in an attempt to slide it into or out of the installation. Pushing or pulling a range (rather than using a lift jack) also increases the possibility of bending the leg spindles or the internal coupling connectors.

5

Image 5
Contents Double Oven GAS Range ALL Ranges can TIP DATA PLATE Conversion Label Installation Instructions Electrical Grounding Instructions Replacement PartsProximity to Side Cabinets  installationGAS and Electric Connection Oven 305 Moving the Cooker Fitting the Adjustable FeetLevelling the Cooker ASSEMBLING THE BACKGUARD It is mandatory to installOR THE ISLAND TRIM Backguard or the island trim28 15/16 735 mm Pressure Regulator Manual Shut-off Valve .1Explosion Hazard Lock Pressure Regulator InstallationImportant use two spanners to tighten the connection Page Range Manifold Manifold male Pipe fitting Rigid Pipe Connections Leak TestingFlexible Connections CONVERSION TO LP/PROPANE GAS SETTING THE PRESSURE REGULATOR .5INJECTORS TABLE Operations to be Performed When Substituting InjectorsSemirapid and triple ring burners Setting the Burner MinimumOven Burner LEFT and RIGHT OVEN Adjustment of the Oven Burner MinimumRecommended ground method Electrical connectionWiring Diagram Page Page Cod ß1