Multiquip MVH-200DA2 manual Loading and Unloading Crane, Maintenance Safety, Emergencies

Page 11

MVH-200DA2 — RULES FOR SAFE OPERATION

Loading and Unloading (Crane):

Before lifting, make sure that machine parts (hook and vibration insulator) are not damaged and screws are not loosened or lost.

Always make sure crane or lifting device has been properly secured to the hook of guard frame on compactor.

NEVER lift the machine while the engine is running.

Use adequate lifting cable (wire or rope) of sufficient strength.

Use one point suspension hook and lift straight upwards.

NEVER allow any person or animal to stand underneath the machine while lifting.

Try not to lift machine to unnecessary heights.

TRANSPORTING

ALWAYS shutdown engine before transporting.

Tighten fuel tank cap securely and close fuel cock to prevent fuel from spilling.

Drain fuel when transporting compactor over long distances or bad roads.

ALWAYS tie down the compactor during transportation by securing the compactor's guard frame with rope.

LIFT

Maintenance Safety:

NEVER lubricate components or attempt service on a running machine.

ALWAYS allow the machine a proper amount of time to cool before servicing.

Keep the machinery in proper running condition.

Fix damage to the machine immediately and always replace broken parts.

Dispose of hazardous waste properly. Examples of potentially hazardous waste are used motor oil, fuel and fuel filters.

DO NOT use food or plastic containers to dispose of hazardous waste.

DO NOT pour waste, oil or fuel directly onto the ground, down a drain or into any water source.

Emergencies

ALWAYS know the location of the nearest fire extinguisher.

ALWAYS know the location of the nearest first aid kit.

In emergencies always know the location of the nearest phone or keep a phone on the job site. Also know the phone numbers of the nearest ambulance, doctor and fire department. This information will be invaluable in case of an emergency.

Figure 18. Lifting the Compactor

MVH-200DA2 PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (01/27/06) — PAGE 11

Image 11
Contents Model MVH-200DA2 Page Page MVH-200DA2 -TABLE of Contents Ordering parts has never been easier MVH-200DA2 Reversible Plate Compactor Specifications MVH-200DA2 SpecificationsMVH-200DA2 Dimensions You can be Injured if you do not follow these directions MVH-200DA2 Safety Message Alert SymbolsAlways wear approved respiratory protection when required MVH-200DA2 Safety Message Alert Symbols Alcohol MVH-200DA2 Rules for Safe OperationEmergencies Maintenance SafetyLoading and Unloading Crane Never lift the machine while the engine is runningOperation and Safety Decals MVH-200DA2 Operation and Safety DecalsFrequency/Speed Plate CompactorVibratory Plates ReversibleVibratory PlatesMVH-200DA2 Plate Compactor Components Muffler Used to reduce noise and emissions Cannister to gain access to filter elementMVH-200DA2 Engine Components FuelFuel Check MVH-200DA2 PRE-INSPECTIONBefore Starting Engine Oil CheckStarting the Engine Yanmar engine MVH-200DA2 START-UP ProcedureShut-Down Procedure Emergency Shutdown ProcedureMove the travel lever to the Neutral position MVH-200DA2 OperationTraveling To Turn The CompactorTransporting Stowing the HandleLifting Every 2 years MVH-200DA2 MaintenanceInspection and Maintenance ServiceTables Daily ServiceAir Filter MVH-200DA2 MaintenanceEngine Oil Replacement Checking the Clutch Checking and Replacing the V-Belt and ClutchChecking the V-belt Replacing theV-beltReplacing Hydraulic Oil Hydraulic Oil MaintenanceRefueling Checking The FuelEngine Troubleshooting MVH-200DA2 EnginetroubleshootingPlate Compactor Troubleshooting MVH-200DA2 Plate CompactortroubleshootingPage QTY. Column MVH-200DA2- Explanation of Code in Remarks ColumnNO. Column Part NO. ColumnSuggested Spare Parts Body Assy MVH-200DA2 Decal PlacementMVH-200DA2 Decals Placement MVH-200DA2 Body Assy NUT M12 Vibrating PlateBase Shock AbsorberVibration Assy MVH-200DA2 -VIBRATION AssyRotary SHAFT, Driven Vibrating CaseWASHER, Flat M12 Roller Bearing NJ210MC4Vibration ASSY. MVH-200DA2 -VIBRATION ASSY.Bearing Cover Rotary SHAFT, DriveGEAR, Drive Stop Ring S-50Control A-TYPE Assy MVH-200DA2 Control A-TYPE AssyNUT M16 Handle BracketHandle WASHER, Flat M16Pump A-TYPE Assy MVH-200DA2 Pump A-TYPE AssyPinion BodySpool ShaftThrottle A-TYPE Assy MVH-200DA2 Throttle Lever A-TYPE AssyWASHER, Lock 8MM BootWire GUIDE, AL103F Wire Stopper AY 3DCylinder Block Assy Yanmar L70V6 ENGINE- Cylinder Block AssyYanmar L70V6 Engine Cylinder Block Assy Cylinder Head Assy Yanmar L70V6 ENGINE- Cylinder Head AssyYanmar L70V6- Cylinder Head Assy AIR Cleaner Yanmar L70V6 ENGINE- AIR Cleaner AssyAIR Cleaner Gasket AIR Cleaner AssyAIR Cleaner Body AIR Cleaner CoverMuffler Assy Yanmar L70V6 ENGINE- Muffler AssyExhaust Defector Muffler GasketBolt M 6X14 Plated Stud M 8X18 PlatedCrankshaft and Camshaft Assy Yanmar L70V6 ENGINE- Crankshaft and Camshaft AssyYanmar L70V6 ENGINE- Crankshaft and Camshaft Assy Piston Assy Yanmar L70V6 ENGINE- Piston AssyPiston PIN Piston Rings SET=STDPiston Ring SET 0.S.=0.25 Piston Ring SET 0.2=0.50LUB. OIL Pump & Governor Assy Yanmar L70V6 ENGINE- LUB. OIL Pump and Governor AssyLUB. OIL Pump Cover Adjusting BoltLUB. OIL Pump and Governor Assy LUB. OIL Pump AssyCooling and Starting Device Assy Yanmar L70V6 ENGINE- Cooling and Starting Device AssyTOP COVER, Black Tank GrommetSide Cover B Side Cover aFuel Injection Pump Assy Yanmar L70V6 ENGINE- Fuel Injection Pump AssyL70V6 Engine Fuel Injection Pump Assy Fuel Tank and Fuel Line Assy Yanmar L70V6 ENGINE- Fueltank & Fuel Line AssyYanmar L70V6 Engine Fueltank and Fuel Line Assy Starting Motor and Dynamo Assy Yanmar L70V6 ENGINE- Starting Motor and Dynamo AssyArmature Gear Housing AssyMagnet Switch Starting Motor & Dynamo AssyTOOLS, Labels and Gasket SET Assy Yanmar L70V6-TOOLS, Labels and Gaskets SET AssyDiesel Label HOW to START- E LabelAIR Cooled Label Yanmar LabelAccessories Yanmar L70V6 ENGINE- AccessoriesScrew M6X25 Wire Harness CExhaust Pipe Assy Terms and Conditions of Sale Parts Page Your Local Dealer is Heres HOW to GET Help