Jura Capresso Z9 manual Troubleshooting

Page 51

 

 

7 Troubleshooting

7 Troubleshooting

 

 

 

 

Problem

Cause/Result

Action

 

 

 

When preparing a latte

–

T Turn the setting wheel of the cappuccino

macchiato, the typical

 

frother to the far right and the Milk Foam

three layers do not

 

position ü.

form.

 

T Change the length of the interval to at

 

 

least 30 seconds in programming mode

 

 

(see Chapter 4 ‘Permanent settings in

 

 

programming mode – Product settings’).

Insufficient foam is

The cappuccino frother

produced when the

is dirty.

milk is frothed or

 

milk sprays from the

 

cappuccino frother.

 

T Clean the cappuccino frother (see Chapter 5 ‘Maintenance – Cleaning the cappuccino frother’).

T Dismantle and rinse the cappuccino frother (see Chapter 5 ‘Maintenance – Dismantling and rinsing the cappuccino frother’).

T Check that the air intake pipe is fitted on the cappuccino frother.

T Rinse or replace the air intake pipe. You will find a replacement in the Welcome Pack.

Coffee only comes

Coffee or ground coffee

T Put the grinder on a coarser setting or use

out in drips when it is

has been ground too

coarser ground coffee (see Chapter 1

being prepared.

finely and is blocking the

‘Preparing and using for the first time –

 

system. The same filter

Adjusting the grinder’).

 

cartridge may have been

T Perform descaling (see Chapter 5

 

used several times or

‘Maintenance – Descaling the machine ’).

 

the water hardness set

 

 

incorrectly in the

 

 

programming mode.

 

 

 

 

Water hardness cannot

The CLEARYL Blue filter

T Deactivate the filter cartridge in

be adjusted.

cartridge is activated.

programming mode.

 

 

 

‘Fill bean container.’ is

The bean monitor is

T Clean the bean container (see Chapter 5

not displayed although

dirty.

‘Maintenance – Cleaning the bean

the bean container is

 

container’).

empty.

 

 

 

 

 

51

Page 50 Page 52
Image 51
Page 50 Page 52
Contents Impressa Z9 One Touch TFT Instructions for Use Preparation Control elements Preparing and using for the first timePermanent settings in programming mode Your Impressa Z9 One Touch TFTMaintenance Symbol descriptionImportant Safeguards Special power cord set instructions Important Safeguards Never do or you will void your warranty protection Control elements Button programming Top of the machine Front On/Off button Display Rotary SwitchFilling the bean container Preparing and using for the first timeSetting up the machine Jura on the InternetPreparing and using for the first time ‘Machine is heating.’ ‘Filter rinsing complete’Turn the Rotary Switch to change the water hardness Press the Rotary SwitchOnly fill the water tank with fresh, cold water Adjusting the grinder Determining the waterHardness Filling the water tank Connecting milkPreparing and using for the first time Preparation Ways of preparing a beverage‘Cappuccino’ ‘1 portion milk’ Preparation in ‘coffee à la carte’ mode Espresso and coffee‘Café à la carte’ Special coffee Latte macchiatoCappuccino Warm milk and milk FoamTPress the ‘Latte macchiato’ button Ground coffee ‘Please add ground coffee.’‘Please select product’ ‘Please select product’ appears on the display Permanently settingHold the ‘Coffee’ button down until ‘Enough coffee? Press Button.’ appears‘Normal’, ‘X high’, ‘Low’ Hot waterDaily operation Switching on Daily maintenanceUnder the cappuccino frother Switching offYour Impressa is switched off Place one receptacle under the coffee spout and anotherPermanent settings in programming mode Product settings To ‘40 sec.’ ‘X high’ Volume ‘0.5 oz’ ‘15.0 oz’ ‘Normal’‘Maintenance status 1/7’ TPress the ‘Programming’ button. ‘Programming’TPress the ‘Classic-library’ button. ‘Classic-library’ TPress the ‘Add to favourites’ button. ‘Select position’Press the button at the bottom right Renaming a product Energy-saving modeAutomatic switch-off TPress the ‘Choose language’ button. ‘Choose language’ Turn the Rotary Switch until the program item ‘MachineProgramming mode. Use the Rotary Switch g to select LanguageRinses TPress the ‘Water hardness’ button. ‘Water hardness’ Setting the water‘Maintenance settings 6/7’ ‘Rinse the milk system’ / ‘Automatic’Unit for amount of water Display settingsSettings 5/7’ is displayed ‘Machine settings 5/7’TPress the ‘Product counter’ button. ‘Product counter’ TPress the ‘Colour scheme’ button. ‘Colour scheme’Rinsing the machine ‘Rinse the coffee system’ MaintenanceFrother Cleaning the cappuccino frotherRinsing the machine Rinsing the cappuccinoTPress the ‘Start’ button Keep children Away Avoid contact with skin and eyesInserting and activating the filter Dismantling and rinsing the cappuccino frotherReassemble the cappuccino frother TPress the ‘Filter’ button. ‘Use filter’ Changing the filter ‘Use only original Jura maintenance products!’ Cleaning the machineMaintenance ‘Approximate duration 45 min.’ Descaling the machineRemove the water tank and rinse it thoroughly Firmly attach the frother to the connectorSpout and the hot-water spout Press the Rotary Switch ‘Fill water tank.’Tank thoroughly Cleaning the beanContainer Them back into the machineDisplay messages Machine.’ or ‘Clean machineNow.’ ‘DecalcifyTroubleshooting Other ‘ERROR’ ‘Empty drip tray.’ is‘Fill water tank.’ is System TPress the ‘Factory setting’ button. ‘Factory setting’Transport and environmentally friendly disposal Transport / Emptying31  37  45 cm Technical dataInserting and activating the filter 41 First-time use IndexQuerying information Preparation options 17 ProblemsWater tank 8 Descaling 48 Filling Website Intentionally blank Intentionally blank Jura contact details/ Legal information

Z9 specifications

The Jura Capresso Z9 is a remarkable fully automatic espresso machine that brings the café experience into the comfort of your home. One of its standout features is the patented Pulse Extraction Process (P.E.P.), which optimizes the extraction time of espresso by utilizing short bursts of water. This process allows for greater flavor extraction, ensuring that each shot of espresso is rich and aromatic.

With a sleek and elegant design, the Z9 boasts an intuitive TFT color display that simplifies navigation through its numerous options. Users can easily program their desired coffee strength, temperature, and volume, catering to personal preferences. The machine is equipped with the versatile One-Touch feature, enabling coffee enthusiasts to create a variety of specialty drinks, from espresso and cappuccino to latte macchiato, all at the touch of a button.

Another significant characteristic of the Jura Z9 is its integrated coffee grinder, featuring professional-grade conical burrs. This ensures that the coffee grounds are uniformly sized, leading to an optimal brewing process. The grinder offers several settings, allowing users to select their preferred grind size for the perfect cup of coffee. Moreover, the machine’s dual coffee spouts can be adjusted to accommodate various cup sizes, making it convenient for serving drinks in both small and large containers.

The Z9 also prioritizes convenience with its automatic self-cleaning program. This feature minimizes the time spent on maintenance, allowing users to enjoy their coffee without worrying about upkeep. The machine's intelligent water system (I.W.S.) utilizes RFID technology to monitor the status of the water filter, prompting users when it needs replacement for optimal taste and performance.

In terms of design, the Jura Z9 is compact and modern, featuring a high-quality stainless steel and ABS plastic body that is both functional and stylish. The water reservoir is generously sized, reducing the frequency of refills and enhancing the overall user experience.

In conclusion, the Jura Capresso Z9 stands out as a top-tier choice for coffee enthusiasts seeking a high-quality, convenient, and stylish espresso machine. With its innovative technologies, user-friendly features, and sleek design, it delivers café-quality beverages that satisfy even the most discerning palates.
Top Page Image Contents