Precision Power D2000/1, D3000/1, D500/1, D1000/1 Features, What’S Included, Cea Specifications

Page 4
FEATURES

FEATURES

Advanced Instrumentation Input Stage. 24dB/Octave; HP/LP/FULL; 30-4kHz Crossover. Independent Line Output Crossover 30-4kHz PWM Power Supply

Triple Darlington Output Stage. AP-IVProtection Circuity QBASSTM Bass Boost

High Voltage Input Capability with -12dB Attenuation Switch. Gold Plated RCA Input and Output Connectors. PowerLockTM Speaker and Power Wire Connectors.

WHAT’S INCLUDED

Amplifier (with speaker and power plugs mounted)

(4)Mounting screws and washers 2mm hex wrench

2.5mm hex wrench 3mm hex wrench

CEA SPECIFICATIONS

D500/1

Power Output: 125 Watts RMS x 1 at 4 ohms and < 1% THD+N

Signal to Noise Ratio: -70 dBA (reference 1 Watt into 4 ohms)

Additional Power Output: 270 Watts RMS x 1 at 1 ohm at 14.4 Supply<1% THD+N

D1000/1

Power Output: 185 Watts RMS x 1 at 4 ohms and < 1% THD+N

Signal to Noise Ratio: -68 dBA (reference 1 Watt into 4 ohms)

Additional Power Output: 495 Watts RMS x 1 at 1 ohm at 14.4 Supply<1% THD+N

D2000/1

Power Output: 375 Watts RMS x 1 at 4 ohms and < 1% THD+N

Signal to Noise Ratio: -71 dBA (reference 1 Watt into 4 ohms)

Additional Power Output: 1150 Watts RMS x 1 at 1 ohm at 14.4 Supply<1% THD+N

D3000/1

Power Output: 495 Watts RMS x 1 at 4 ohms and < 1% THD+N

Signal to Noise Ratio: -60 dBA (reference 1 Watt into 4 ohms)

Additional Power Output: 1475 Watts RMS x 1 at 1 ohm at 14.4 Supply<1% THD+N

3

Image 4
Contents AMPLIFIER MODELS D500/1D1000/1 D2000/1TABLE OF CONTENTS SERVICE CONGRATULATIONSCEA SPECIFICATIONS FEATURESWHAT’S INCLUDED SPECIFICATIONS Nominal Power RatingsGeneral Specifications D500/1Fuse The LEDs provide the following indications Small flat blade screwdriver When using 16 gauge wire or larger, run the speaker wires from the amplifier location through the vehicle to the speakers. Observe the same precautions for routing these wires that you followed for running the power and remote turn on wires. Cut off excess and, using wire strippers, strip 1/4-inchof insulation. Locate the speaker/remote turn- on PowerLockTM connector. Using a hex wrench loosen the screws on the upperside of the connector. Insert the speaker leads into the end and secure with the hex wrench. Check to be sure youve maintained proper polarity before securing each wire POWERLOCKTM Total RMS output X 1.3 = Total Input Wattage 1300W= 108 Amps total current draw 12V Power wires POWERLOCK CONNECTORS3mm hex wrenchFRONT PLATE DIAGRAMS XOVER12 D500/1, D1000/1 END PLATE DIAGRAMSD2000/1, D3000/1 ADVANCED INSTRUMENTATION INPUT INPUTSSOURCE Headunit Optional QBASS REMOTETM QBASS PLUSTMQBASS PLUS SPECIFICATIONS QBASSTM Settings D500/1, D1000/1, D2000/1, and D3000/1 TC-XCROSSOVERCROSSOVER DETENT CHART ADJUSTING INPUT GAIN TROUBLESHOOTINGHIGH MASS INTERNAL HEATSINK AP-IVPROTECTION CIRCUITPrecision PowerTM Dealer or OPPOSITE CHANNELSAME CHANNEL OPPOSITE CHANNELLIMITED TWO YEAR CONSUMER WARRANTY