Kenmore 795.5131 manual Connect the Tubing to, Start the Icemaker, Fasten Shutoff Valve

Page 13

4. FASTEN

THE SHUTOFF

VALVE

&FLUSH

OUT

THE TUBING

 

Fasten the

shutoff valve to

the cold water pipe with the pipe

Turn the

main

water

supply

on and

flush out

clamp.

 

 

the tubing

until

the

water is dear.

 

 

 

 

Shut the water off at the water valve after

Pipe Clamp--_k

 

about one

quart of

water

has been

flushed

 

 

 

through

the tubing.

 

 

 

Saddle-Type j

_ __

Vertical

Cold

Shutoff Valve

 

Water

Pipe

NOTE: Commonwealth of Massachusetts Plumbing Codes 248CMR shall be adhered to. Saddle valves are illegal and use is not permitted in Massachusetts. Consult with your licensed plumber.

&TIGHTEN THE PiPE CLAMP

Tighten the clamp screws until the sealing washer begins to

swell.Washer

Pipe Clamp

--

Inlet End

Clamp Screw-

 

 

9.CONNECT THE TUBING TO THE

REFRIGERATOR

NOTES:

*Before making the connection to the refrigerator, be sure the refrigerator power cord is not plugged into the wall outlet.

°If your refrigerator does not have a water filter, we recommend installing one. If your water supply has sand or particles that could clog the screen of the refrigerator's water valve, install the filter in the water line near the refrigerator.

°Do not use old hoses; only use new hoses provided by the manufacturer. For more information caii 1-800-4-MY-

HOME®.

1.Remove the plastic flexible cap from the refrigerator connection.

2.Place the compression nut and ferrule (sleeve) onto the end of the tubing. (See figure 1)

3.Insert the end of the tubing into the connection as far as possible. While holding the tubing, tighten the fitting.

CAUTION: Review that leaks are not occurring in the water line.

Back of refrigerator

NOTE: Do not overtighten or you may crush the tubing.

&ROUTE THE TUBING

Route the tubing between the cold water line and the refrigerator. Route the tubing through a hole drilled in the wail or floor (behind the refrigerator or adjacent base cabinet] as close to the wail as possible.

NOTE: Be sure there is sufficient extra tubing [about 8 feet (2.4 m) coiled into 3 turns of about 10" (254 mm) diameter]

to allow the refrigerator to move out from the wail after installation.

7.CONNECT THE TUBING TO THE VALVE

Place the compression nut and ferrule (sleeve) for copper tubing onto the end of the tubing and connect it to the shutoff valve. Make sure the tubing is fully inserted into the valve. Tighten the compression nut securely.

Saddle-TypeCompression

Shutoff Valve

Nut

1/4"(6.35 mm) Tubing

Tubing

1/4" (6.35 ram'

)

Compression

 

Ferrule

 

(Sleeve)

 

Nut _

 

 

Refrigerator

Figure 1

Connection

 

Fasten the tubing into the tubing clamp attached to the back of the refrigerator. First, loosen the screw fastening the clamp. Next, insert the tubing in the groove. Finally, re-fasten the screw.

Pacldng"__

Nut

_rule(sleeve)

Outlet

Valve

NOTE: Commonwealth of Massachusetts Plumbing Codes 248CMR shall be adhered to. Saddle valves are illegal and use is not permitted in Massachusetts. Consult with your licensed plumber.

10. PLUG IN THE REFRIGERATOR Arrange the coil of tubing so that it does not vibrate against the back of the refrigerator or against the wall. Push the refrigerator back to the wall.

11.START THE ICEMAKER

Set the icemaker power switch to the ON position. The icemaker wil! not begin to operate until it reaches its operating temperature of 15°F (-9°C) or below. It will then

begin operation automatically if the icemaker power switch is

in the I (on) position. 14

Image 13
Contents Kenmoreo Filter Troubleshooting GuideUSE and Care SIDE=BY=SIDEREFRIGERATOR Kenmore Refrigerator Warranty One Year Limited WarrantyService Product warrantyMaintenance Check MasterProtection AgreementsUsing this Basic safetyTo reduce Shock orTo Connect Electricity USE of Extension CordsElectrical Shock Hazard Recommended Grounding MethodUnpacking Your Refrigerator InstallationHandle Removal Type 1 identify your handle type Leveling the Refrigerator DoorHandle Removal Type Grille InstallationEJectrlc Shock Hazard SomeType Door Alignment Adjusting tool fiat blade screwdriverWhat YOU will Need Connecting the Water Line Before YOU BeginShutoff the Main Water Supply Choose the Valve LocationStart the Icemaker Connect the Tubing toFasten Shutoff Valve Tighten the PiPE ClampFreezer Door Rack Dairy Corner Display Off Mode Control Panel FeaturesEnsuring Proper AIR Circulation Food Storage GuideAdjusting Control Settings Recommended AdjustmentCONDITION/REASON Food Storage Guide How to StoreStoring Frozen Food Packaging recommendationsICE Storage BIN Water and ICE DispenserIcenaker Cover Door Rack and SupportRefrigerator Shelves Crisper and Crisper CoverDoor Snack PANFreezershelf Insfallng the wafer filter Water FilterOdor SystemGeneral Cleaning Tips Lamp ReplacementPower iNTERRUPTiONS INSiDE WallsWhen YOU Move When YOU GO on VacationWhen should YOU SET the Icemaker Power Switch to OFF Icemaker OperationUnderstanding Sounds YOU MAY Hear Icemaker See the Adjusting Control Settings sectionIce Ice or Wild Not StorageInto SectionPosterior Garantja