Murray 465609x24A IMPORTANT! Before YOU Start Mowing, HOW to Prepare the Engine, Check the Tires

Page 14

ASSEMBLY

IMPORTANT! BEFORE YOU START MOWING

-Check the engine oil.

-Fill the fuel tank with gasoline.

-Check the level of the mower housing.

-Check the air pressure of the tires.

-Make sure the battery cables are attached.

WARNING: Before doing any assembly or mainte- nance to the mower, remove the wire from the spark plug.

NOTE: In this instruction book, left and right describe the loca- tion of a part with the operator on the seat.

HOW TO PREPARE THE ENGINE

NOTE: The engine was shipped from the factory filled with oil. Check the level of the oil. Add oil as needed.

See the engine manufacturer’s instructions for the type of gasoline and oil to use. Before you use the unit, read the information on safety, operation, maintenance, and storage.

WARNING: Follow the engine manufacturer’s instructions for the type of gasoline and oil to use. Always use a safety gasoline container. Do not smoke when adding gasoline to the engine. When inside an enclosure, do not fill with gasoline. Before you add gasoline, stop the engine. Let the engine cool for several minutes.

IMPORTANT: This unit is equipped with an internal combustion engine and must not be used on or near any unimproved

forest–covered, brush–covered or grass–covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it must be maintained in effective working order by the operator.

In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. See an Authorized Service Center for a spark arrester for the muffler.

In some areas, local law requires the use of a resistor spark plug to control the ignition signals. See an Authorized Service Center for a resistor spark plug for the engine.

NOTE: Actual sustained horsepower will likely be lower due to operating limitations and environmental factors.

CHECK THE LEVEL OF THE MOWER HOUSING

Make sure the level of cut is still correct. After you mow a short distance, look at the area that was cut. If the mower housing does not cut level, see the instructions on “How To Level The Mower Housing” in the Maintenance section of this instruction book.

CHECK THE TIRES

Check the air pressure in the tires. Tires with too much air pressure will cause the unit to ride rough. Also, the wrong air pressure will keep the mower housing from cutting level. The correct air pressure (PSI) is 14 PSI (1 BAR). The tires were over inflated for shipment.

F–030758L

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Model Table of Contents Safe Operation Practices for Ride-on Mowers OWNER’S InformationEnvironmental Awareness II. Slope operation Safe Mowing Guide Safe Mowing Guide Safe Mowing Guide Steps to Follow Before MowingInternational Pictorials Safety Warning PictorialsInternational Pictorials Control And Operating PictorialsAssembly AssemblyHOW to Assemble the Gauge Wheels HOW to Install the SeatHOW to Assemble the Steering Wheel HOW to Install the Mower Housing Attach the extension spring to the blade control rod. MakeHOW to Install the Battery Cables Maintenance Free BatteryHOW to Charge Maintenance Free Battery Remove the battery and battery trayIMPORTANT! Before YOU Start Mowing HOW to Prepare the EngineCheck the Level of the Mower Housing Check the TiresOperation Location of ControlsHOW to USE the Throttle Control AttachmentsTo 1/2 HOW to USE the Speed Control PedalHOW to Disconnect the Transmission To 2/3HOW to Stop the Unit HOW to SET the Parking BrakeHOW to Change the Cutting Height HOW to Transport the UnitHOW to Operate with the Mower Housing HOW to Operate the Unit on HillsCarburetor HOW to Start the EngineBefore Starting the Engine Operating Tips Mowing and Bagging TipsHOW to Check the Muffler MaintenanceFrequency Maintenance Required Comments General RecommendationsInspect Blade HOW to Remove and Install the BladeHOW to Sharpen the Blade Mount the blade and blade adapter on the mandrelHOW to Adjust the Blade Rotation Control HOW to Check and Adjust the Motion Drive Belt Remove the 1/4 inch 6 mm pin or bolt FigureHOW to Check and Adjust the Drive Brake Disconnect the red cable from the positive + terminalWhere to Lubricate HOW to Check the Fuel FilterAttach the extension spring to the blade control rod. See HOW to Remove the Mower HousingRemove the mower drive belt from the stack pulley 5,6 HOW to Adjust the Gauge WheelsLift Lever Hole No Position No HOW to Level the Mower Housing Remove the mid-idler pulley HOW to Replace the Motion Drive BeltInstall the mid-idler pulley Assemble the left pulley cover HOW to Replace the Primary Mower Drive BeltHOW to Replace the Secondary Mower Drive Belt Remove the primary mower drive belt from the stack pulleyHOW to Install the Wheels Fasten the rear wheel with washer and e-ringHOW to Clean the Mower Housing HOW to Replace the FuseHOW to Replace the Light Bulb BatteryTrouble Shooting Chart 030758L USA030758L Repair Parts Chassis & HoodKey Description Drive Assembly Drive Assembly Steering Repair Parts Mower Housing Suspension Repair Parts Mower Housing 7601031 Repair Parts Engine Mount Assembly Engine Mount Assembly Repair Parts Electrical System Electrical System Key Part Description030758L 030758L 030758L Index Model No Model No Bushel Capacity

465609x24A specifications

Murray 465609x24A is a versatile and robust equipment designed for a variety of applications, particularly in the fields of agriculture and industrial use. Engineered for durability and efficiency, this model is built to withstand rigorous conditions while providing high performance.

One of the standout features of the Murray 465609x24A is its powerful engine. It is equipped with a state-of-the-art propulsion system that ensures maximum output with minimal fuel consumption. The engine's advanced technology allows for smooth operation, whether it's powering through tough terrains or handling heavy loads. This makes it ideal for users who demand reliability in challenging environments.

In addition to its powerful engine, the 465609x24A incorporates advanced safety features which are paramount for both operator protection and equipment longevity. An integrated sensor system continuously monitors the machine’s performance, automatically adjusting parameters to prevent overheating and maintain optimal working conditions. This technology not only enhances safety but also extends the lifespan of the equipment.

The design of the Murray 465609x24A is fundamentally user-centric. It features an ergonomic layout that allows for ease of operation. The controls are intuitively placed, enabling operators to manage tasks efficiently without unnecessary complication. The spacious cabin allows for extended use without compromising comfort, which is essential during long workdays.

Furthermore, the 465609x24A includes a versatile attachment system, accommodating a wide range of tools and implements. This adaptability enhances its functionality, allowing users to tailor the machine according to specific tasks—whether it’s plowing, lifting, or transporting materials.

Maintenance is simplified with the Murray 465609x24A. The design includes easy access points for routine checks, making it straightforward for operators to conduct maintenance tasks. This emphasis on serviceability ensures that the machine remains in peak operational condition, reducing downtime and increasing productivity.

In conclusion, the Murray 465609x24A stands out as a reliable, efficient, and adaptable piece of machinery. With its powerful engine, robust safety features, user-friendly design, and easy maintenance, it is a formidable choice for those in need of a dependable workhorse in demanding environments. The combination of these characteristics makes the Murray 465609x24A a leading choice in its category, appealing to both professional and industrial users alike.
Top Page Image Contents