Murray 465609x24A HOW to Replace the Primary Mower Drive Belt, Assemble the left pulley cover

Page 32

MAINTENANCE

HOW TO REPLACE THE PRIMARY

MOWER DRIVE BELT

1.Remove the mower housing. See the instructions on “How To Remove The Mower Housing”.

2.Remove the three screws from the left pulley cover. Remove the pulley cover.

3.To remove the primary mower drive belt from the left man- drel pulley, slide the primary mower drive belt between the left mandrel pulley and the belt guides.

4.Pull the belt retainer away from the idler pulley. Remove the primary mower drive belt from the idler pulley.

5.Move the brake pad assembly away from the stack pulley. Remove the primary mower drive belt from the stack pulley.

NOTE: Replace the primary mower drive belt with an original equipment belt. See an authorized service center in your area.

6.Install a new primary mower drive belt. Pull the brake pad as- sembly away from the stack pulley. Put the belt around the stack pulley. Make sure the primary mower drive belt is in- side of the belt guide.

7.Pull the belt retainer away from the idler pulley. Put the flat side of the primary mower drive belt around the idler pulley.

8.Make sure the “V” side of the primary mower drive belt is against the mandrel pulleys as shown.

9.Make sure the primary mower drive belt is inside all the belt guides.

10.Assemble the left pulley cover.

11.Install the mower housing. See the instructions on “How To In- stall The Mower Housing”.

12.Before you mow, check the blade rotation control. See the in- structions on “How To Adjust The Blade Rotation Control”.

HOW TO REPLACE THE SECONDARY MOWER DRIVE BELT

1.Remove the mower housing. See the instructions on “How To Remove The Mower Housing”.

2.Remove the primary mower drive belt from the stack pulley.

3.Remove the two screws from the right pulley cover. Remove the right pulley cover.

4.Pull the idler pulley away from the secondary mower drive belt. Remove the belt from the idler pulley.

5.Remove the secondary mower drive belt from the right man- drel pulley.

6.Remove the secondary mower drive belt from the stack pulley.

NOTE: Replace the secondary mower drive belt with an original equipment belt. See an authorized service center in your area.

7.Install a new secondary mower drive belt. Put the belt around the bottom of the stack pulley. Make sure the secondary mower drive belt is inside the belt guide next to the stack pulley.

8.Put the secondary mower drive belt around the right drive pulley.

9.Pull the idler pulley toward the front. Install the flat side of the secondary mower drive belt against the idler pulley.

10.Make sure the “V” side of the secondary mower drive belt is around the right mandrel pulley.

11.Assemble the right pulley cover.

12.Put the primary mower drive belt around the stack pulley.

13.Install the mower housing. See the instructions on “How To In- stall The Mower Housing”.

14.Before you mow, check the blade rotation control. See the in- structions on “How To Adjust The Blade Rotation Control”.

 

 

 

Left

 

 

Screw

Pulley Cover

Screw

 

 

 

 

 

Idler Pulley

Belt

 

 

 

 

Right Pulley Cover

 

Retainer

 

 

Stack Pulley

Left

 

 

 

Mandrel Pulley

 

Brake Pad

Belt Guide

 

 

Assembly

 

 

 

Belt Guide

 

 

 

 

Secondary

 

 

 

Mower Drive Belt

 

 

Right

 

 

 

Mandrel

 

 

 

Pulley

 

 

 

 

 

 

Brake Pad Assembly

 

 

 

Primary Mower Drive Belt

 

Idler Pulley

 

Figure 37

 

 

 

F–030758L

 

32

 

Image 32
Contents Model Table of Contents Safe Operation Practices for Ride-on Mowers OWNER’S InformationEnvironmental Awareness II. Slope operation Safe Mowing Guide Safe Mowing Guide Safe Mowing Guide Steps to Follow Before MowingSafety Warning Pictorials International PictorialsInternational Pictorials Control And Operating PictorialsAssembly AssemblyHOW to Assemble the Gauge Wheels HOW to Install the SeatHOW to Assemble the Steering Wheel HOW to Install the Mower Housing Attach the extension spring to the blade control rod. MakeMaintenance Free Battery HOW to Charge Maintenance Free BatteryHOW to Install the Battery Cables Remove the battery and battery trayHOW to Prepare the Engine Check the Level of the Mower HousingIMPORTANT! Before YOU Start Mowing Check the TiresOperation Location of ControlsHOW to USE the Throttle Control AttachmentsHOW to USE the Speed Control Pedal HOW to Disconnect the TransmissionTo 1/2 To 2/3HOW to SET the Parking Brake HOW to Change the Cutting HeightHOW to Stop the Unit HOW to Transport the UnitHOW to Operate with the Mower Housing HOW to Operate the Unit on HillsCarburetor HOW to Start the EngineBefore Starting the Engine Operating Tips Mowing and Bagging TipsMaintenance Frequency Maintenance Required CommentsHOW to Check the Muffler General RecommendationsHOW to Remove and Install the Blade HOW to Sharpen the BladeInspect Blade Mount the blade and blade adapter on the mandrelHOW to Adjust the Blade Rotation Control HOW to Check and Adjust the Motion Drive Belt Remove the 1/4 inch 6 mm pin or bolt FigureHOW to Check and Adjust the Drive Brake Disconnect the red cable from the positive + terminalWhere to Lubricate HOW to Check the Fuel FilterAttach the extension spring to the blade control rod. See HOW to Remove the Mower HousingRemove the mower drive belt from the stack pulley 5,6 HOW to Adjust the Gauge WheelsLift Lever Hole No Position No HOW to Level the Mower Housing Remove the mid-idler pulley HOW to Replace the Motion Drive BeltInstall the mid-idler pulley HOW to Replace the Primary Mower Drive Belt HOW to Replace the Secondary Mower Drive BeltAssemble the left pulley cover Remove the primary mower drive belt from the stack pulleyHOW to Install the Wheels Fasten the rear wheel with washer and e-ringHOW to Replace the Fuse HOW to Replace the Light BulbHOW to Clean the Mower Housing BatteryTrouble Shooting Chart 030758L USA030758L Repair Parts Chassis & HoodKey Description Drive Assembly Drive Assembly Steering Repair Parts Mower Housing Suspension Repair Parts Mower Housing 7601031 Repair Parts Engine Mount Assembly Engine Mount Assembly Repair Parts Electrical System Electrical System Key Part Description030758L 030758L 030758L Index Model No Model No Bushel Capacity

465609x24A specifications

Murray 465609x24A is a versatile and robust equipment designed for a variety of applications, particularly in the fields of agriculture and industrial use. Engineered for durability and efficiency, this model is built to withstand rigorous conditions while providing high performance.

One of the standout features of the Murray 465609x24A is its powerful engine. It is equipped with a state-of-the-art propulsion system that ensures maximum output with minimal fuel consumption. The engine's advanced technology allows for smooth operation, whether it's powering through tough terrains or handling heavy loads. This makes it ideal for users who demand reliability in challenging environments.

In addition to its powerful engine, the 465609x24A incorporates advanced safety features which are paramount for both operator protection and equipment longevity. An integrated sensor system continuously monitors the machine’s performance, automatically adjusting parameters to prevent overheating and maintain optimal working conditions. This technology not only enhances safety but also extends the lifespan of the equipment.

The design of the Murray 465609x24A is fundamentally user-centric. It features an ergonomic layout that allows for ease of operation. The controls are intuitively placed, enabling operators to manage tasks efficiently without unnecessary complication. The spacious cabin allows for extended use without compromising comfort, which is essential during long workdays.

Furthermore, the 465609x24A includes a versatile attachment system, accommodating a wide range of tools and implements. This adaptability enhances its functionality, allowing users to tailor the machine according to specific tasks—whether it’s plowing, lifting, or transporting materials.

Maintenance is simplified with the Murray 465609x24A. The design includes easy access points for routine checks, making it straightforward for operators to conduct maintenance tasks. This emphasis on serviceability ensures that the machine remains in peak operational condition, reducing downtime and increasing productivity.

In conclusion, the Murray 465609x24A stands out as a reliable, efficient, and adaptable piece of machinery. With its powerful engine, robust safety features, user-friendly design, and easy maintenance, it is a formidable choice for those in need of a dependable workhorse in demanding environments. The combination of these characteristics makes the Murray 465609x24A a leading choice in its category, appealing to both professional and industrial users alike.