Murray 465609x24A manual HOW to Operate with the Mower Housing, HOW to Operate the Unit on Hills

Page 19

OPERATION

HOW TO OPERATE WITH THE MOWER HOUSING

WARNING: The deflector is a safety device. Do not re- move the deflector. The deflector forces the dis- charged material toward the ground. Always keep the deflector in the down position. If the deflector is dam- aged, replace the deflector with an original equipment part from an authorized service center.

1.Start the engine.

2.Release the parking brake.

3.Move the lift lever to a height of cut position. In high or thick grass, cut the grass in the highest position first and then lower the mower housing to a lower position.

CAUTION: Do not operate with the mower housing in the LEVEL ADJUSTMENT position. If you operate in the LEVEL ADJUSTMENT position, the mower housing and blades can be damaged.

4.Move the throttle control to the SLOW position.

5.Move the blade rotation control to the ENGAGE position.

6.Move the throttle control to the FAST position.

7.Slowly push the speed control pedal to the desired speed.

NOTE: When you mow in heavy grass or mow with a grass bagger, use a slow forward speed.

8.Make sure the level of cut set at the factory is still correct. After you mow a short distance, look at the area that was cut. If the mower housing does not cut level, see the instructions on “How To Level The Mower Housing” in the Maintenance section.

WARNING: For better control of the unit, always select a safe speed.

HOW TO OPERATE THE UNIT ON HILLS

WARNING: Do not ride up or down slopes that are too steep to back straight up. Never ride the unit across a slope. See the “Slope Guide” in the back of this book for information on how to check slopes.

HOW TO OPERATE ON A HILL

1.Control the speed only with the speed control pedal. Do not use the brake pedal on a hill.

2.To help prevent an accident, slowly move the speed control pedal. Avoid sudden turns or changes in speed.

3.To reduce forward speed when going down a hill, slowly release the speed control pedal until the unit slows to the desired speed.

HOW TO STOP ON A HILL

1.Avoid stopping on a hill. If you must quickly stop in an emergen- cy, remove your right foot from the speed control pedal and quickly depress the left brake pedal.

2.Set the parking brake.

3.Before you dismount from the seat, move the throttle control to SLOW position, move the blade rotation control to the DISEN- GAGED position, turn off the engine and set the parking brake.

HOW TO START OPERATION ON A HILL

1.Start the engine

2.Move the blade rotation control to the ENGAGED position.

3.Move the throttle control to the FAST position.

4.Depress the brake pedal and release the parking brake. As you release the parking brake, push the speed control pedal to the desired speed.

WARNING: Slowly push the speed control pedal as you release the parking brake. The parking brake must be disengaged before the speed control pedal is able to engage the transmission.

F–030758L

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Model Table of Contents Environmental Awareness OWNER’S InformationSafe Operation Practices for Ride-on Mowers II. Slope operation Safe Mowing Guide Safe Mowing Guide Safe Mowing Guide Before Mowing Steps to FollowControl And Operating Pictorials Safety Warning PictorialsInternational Pictorials International PictorialsAssembly AssemblyHOW to Assemble the Steering Wheel HOW to Install the SeatHOW to Assemble the Gauge Wheels Attach the extension spring to the blade control rod. Make HOW to Install the Mower HousingRemove the battery and battery tray Maintenance Free BatteryHOW to Charge Maintenance Free Battery HOW to Install the Battery CablesCheck the Tires HOW to Prepare the EngineCheck the Level of the Mower Housing IMPORTANT! Before YOU Start MowingLocation of Controls OperationAttachments HOW to USE the Throttle ControlTo 2/3 HOW to USE the Speed Control PedalHOW to Disconnect the Transmission To 1/2HOW to Transport the Unit HOW to SET the Parking BrakeHOW to Change the Cutting Height HOW to Stop the UnitHOW to Operate the Unit on Hills HOW to Operate with the Mower HousingBefore Starting the Engine HOW to Start the EngineCarburetor Mowing and Bagging Tips Operating TipsGeneral Recommendations MaintenanceFrequency Maintenance Required Comments HOW to Check the MufflerMount the blade and blade adapter on the mandrel HOW to Remove and Install the BladeHOW to Sharpen the Blade Inspect BladeHOW to Adjust the Blade Rotation Control Remove the 1/4 inch 6 mm pin or bolt Figure HOW to Check and Adjust the Motion Drive BeltDisconnect the red cable from the positive + terminal HOW to Check and Adjust the Drive BrakeHOW to Check the Fuel Filter Where to LubricateRemove the mower drive belt from the stack pulley HOW to Remove the Mower HousingAttach the extension spring to the blade control rod. See Lift Lever Hole No Position No HOW to Adjust the Gauge Wheels5,6 HOW to Level the Mower Housing Install the mid-idler pulley HOW to Replace the Motion Drive BeltRemove the mid-idler pulley Remove the primary mower drive belt from the stack pulley HOW to Replace the Primary Mower Drive BeltHOW to Replace the Secondary Mower Drive Belt Assemble the left pulley coverFasten the rear wheel with washer and e-ring HOW to Install the WheelsBattery HOW to Replace the FuseHOW to Replace the Light Bulb HOW to Clean the Mower HousingTrouble Shooting Chart USA 030758L030758L Chassis & Hood Repair PartsKey Description Drive Assembly Drive Assembly Steering Repair Parts Mower Housing Suspension Repair Parts Mower Housing 7601031 Repair Parts Engine Mount Assembly Engine Mount Assembly Repair Parts Electrical System Key Part Description Electrical System030758L 030758L 030758L Index Model No Bushel Capacity Model No

465609x24A specifications

Murray 465609x24A is a versatile and robust equipment designed for a variety of applications, particularly in the fields of agriculture and industrial use. Engineered for durability and efficiency, this model is built to withstand rigorous conditions while providing high performance.

One of the standout features of the Murray 465609x24A is its powerful engine. It is equipped with a state-of-the-art propulsion system that ensures maximum output with minimal fuel consumption. The engine's advanced technology allows for smooth operation, whether it's powering through tough terrains or handling heavy loads. This makes it ideal for users who demand reliability in challenging environments.

In addition to its powerful engine, the 465609x24A incorporates advanced safety features which are paramount for both operator protection and equipment longevity. An integrated sensor system continuously monitors the machine’s performance, automatically adjusting parameters to prevent overheating and maintain optimal working conditions. This technology not only enhances safety but also extends the lifespan of the equipment.

The design of the Murray 465609x24A is fundamentally user-centric. It features an ergonomic layout that allows for ease of operation. The controls are intuitively placed, enabling operators to manage tasks efficiently without unnecessary complication. The spacious cabin allows for extended use without compromising comfort, which is essential during long workdays.

Furthermore, the 465609x24A includes a versatile attachment system, accommodating a wide range of tools and implements. This adaptability enhances its functionality, allowing users to tailor the machine according to specific tasks—whether it’s plowing, lifting, or transporting materials.

Maintenance is simplified with the Murray 465609x24A. The design includes easy access points for routine checks, making it straightforward for operators to conduct maintenance tasks. This emphasis on serviceability ensures that the machine remains in peak operational condition, reducing downtime and increasing productivity.

In conclusion, the Murray 465609x24A stands out as a reliable, efficient, and adaptable piece of machinery. With its powerful engine, robust safety features, user-friendly design, and easy maintenance, it is a formidable choice for those in need of a dependable workhorse in demanding environments. The combination of these characteristics makes the Murray 465609x24A a leading choice in its category, appealing to both professional and industrial users alike.
Top Page Image Contents