Murray 465609x24A manual Operating Tips, Mowing and Bagging Tips

Page 21

OPERATION

OPERATING TIPS

1.Check the blade rotation control for correct adjustment. For the blade(s) to disengage correctly, the adjustment must be cor- rect.

2.Before you use the unit, check the oil in the engine and add oil if necessary.

3.If the engine will not start, first make sure the wire is attached to the spark plug.

4.Make sure all the belts are inside all the belt guides. See the in- structions on how to remove and install the motion drive and mower drive belts.

5.Before you make an inspection, adjustment (except for the car- buretor) or repair, make sure the wire from the spark plug is dis- connected.

6.For longer life of the battery on electric start models, charge the battery every three months.

7.Use the speed control pedal to change the ground speed, not the throttle control.

8.Belt noise can occur when the blade is engaged. This noise is normal and does not affect the operation of the unit.

MOWING AND BAGGING TIPS

1.For a lawn to look better, check the cutting level of the mower housing. See “How To Level The Mower Housing” in the Main- tenance section.

2.For the mower housing to cut level, make sure the tires have the correct amount of air pressure.

3.Every time you use the unit, check the blade. If the blade is bent or damaged, immediately replace the blade. Also, make sure the nut for the blade is tight.

4.Keep the blade(s) sharpened. Worn blades will cause the ends of the grass to turn brown.

5.Do not cut or bag grass that is wet. Wet grass will not discharge correctly. Let the grass dry before cutting.

6.Use the left side of the mower housing to trim near an object.

7.Discharge the cut grass onto the mowed area. The result is a more even discharge of cut grass.

8.When you mow large areas, start by turning to the right so that the cut grass will discharge away from shrubs, fences, drive- ways, etc. After one or two rounds, mow in the opposite direc- tion making left turns until finished (Figure 13).

9.If the grass is very high, cut two times to decrease the load on the engine. First cut with the mower housing in the highest posi- tion and then lower the mower housing for the second cut.

10.For better engine performance and an even discharge of the cut grass, always operate the engine with the throttle in FAST position.

11.When you use a bagger, operate the engine with the throttle in FAST position and the speed control pedal pushed 1/3 forward.

12.For better cutting performance and a quality cut, mow with the speed control pedal pushed 1/3 to 1/2 forward.

13.After each use, clean the bottom and top of the mower housing for better performance. Also, a clean mower housing will help prevent a fire.

Figure 13

F–030758L

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Model Table of Contents OWNER’S Information Environmental AwarenessSafe Operation Practices for Ride-on Mowers II. Slope operation Safe Mowing Guide Safe Mowing Guide Safe Mowing Guide Before Mowing Steps to FollowInternational Pictorials Safety Warning PictorialsInternational Pictorials Control And Operating PictorialsAssembly AssemblyHOW to Install the Seat HOW to Assemble the Steering WheelHOW to Assemble the Gauge Wheels Attach the extension spring to the blade control rod. Make HOW to Install the Mower HousingHOW to Charge Maintenance Free Battery Maintenance Free BatteryHOW to Install the Battery Cables Remove the battery and battery trayCheck the Level of the Mower Housing HOW to Prepare the EngineIMPORTANT! Before YOU Start Mowing Check the TiresLocation of Controls OperationAttachments HOW to USE the Throttle ControlHOW to Disconnect the Transmission HOW to USE the Speed Control PedalTo 1/2 To 2/3HOW to Change the Cutting Height HOW to SET the Parking BrakeHOW to Stop the Unit HOW to Transport the UnitHOW to Operate the Unit on Hills HOW to Operate with the Mower HousingHOW to Start the Engine Before Starting the EngineCarburetor Mowing and Bagging Tips Operating TipsFrequency Maintenance Required Comments MaintenanceHOW to Check the Muffler General RecommendationsHOW to Sharpen the Blade HOW to Remove and Install the BladeInspect Blade Mount the blade and blade adapter on the mandrelHOW to Adjust the Blade Rotation Control Remove the 1/4 inch 6 mm pin or bolt Figure HOW to Check and Adjust the Motion Drive BeltDisconnect the red cable from the positive + terminal HOW to Check and Adjust the Drive BrakeHOW to Check the Fuel Filter Where to LubricateHOW to Remove the Mower Housing Remove the mower drive belt from the stack pulleyAttach the extension spring to the blade control rod. See HOW to Adjust the Gauge Wheels Lift Lever Hole No Position No5,6 HOW to Level the Mower Housing HOW to Replace the Motion Drive Belt Install the mid-idler pulleyRemove the mid-idler pulley HOW to Replace the Secondary Mower Drive Belt HOW to Replace the Primary Mower Drive BeltAssemble the left pulley cover Remove the primary mower drive belt from the stack pulleyFasten the rear wheel with washer and e-ring HOW to Install the WheelsHOW to Replace the Light Bulb HOW to Replace the FuseHOW to Clean the Mower Housing BatteryTrouble Shooting Chart USA 030758L030758L Chassis & Hood Repair PartsKey Description Drive Assembly Drive Assembly Steering Repair Parts Mower Housing Suspension Repair Parts Mower Housing 7601031 Repair Parts Engine Mount Assembly Engine Mount Assembly Repair Parts Electrical System Key Part Description Electrical System030758L 030758L 030758L Index Model No Bushel Capacity Model No

465609x24A specifications

Murray 465609x24A is a versatile and robust equipment designed for a variety of applications, particularly in the fields of agriculture and industrial use. Engineered for durability and efficiency, this model is built to withstand rigorous conditions while providing high performance.

One of the standout features of the Murray 465609x24A is its powerful engine. It is equipped with a state-of-the-art propulsion system that ensures maximum output with minimal fuel consumption. The engine's advanced technology allows for smooth operation, whether it's powering through tough terrains or handling heavy loads. This makes it ideal for users who demand reliability in challenging environments.

In addition to its powerful engine, the 465609x24A incorporates advanced safety features which are paramount for both operator protection and equipment longevity. An integrated sensor system continuously monitors the machine’s performance, automatically adjusting parameters to prevent overheating and maintain optimal working conditions. This technology not only enhances safety but also extends the lifespan of the equipment.

The design of the Murray 465609x24A is fundamentally user-centric. It features an ergonomic layout that allows for ease of operation. The controls are intuitively placed, enabling operators to manage tasks efficiently without unnecessary complication. The spacious cabin allows for extended use without compromising comfort, which is essential during long workdays.

Furthermore, the 465609x24A includes a versatile attachment system, accommodating a wide range of tools and implements. This adaptability enhances its functionality, allowing users to tailor the machine according to specific tasks—whether it’s plowing, lifting, or transporting materials.

Maintenance is simplified with the Murray 465609x24A. The design includes easy access points for routine checks, making it straightforward for operators to conduct maintenance tasks. This emphasis on serviceability ensures that the machine remains in peak operational condition, reducing downtime and increasing productivity.

In conclusion, the Murray 465609x24A stands out as a reliable, efficient, and adaptable piece of machinery. With its powerful engine, robust safety features, user-friendly design, and easy maintenance, it is a formidable choice for those in need of a dependable workhorse in demanding environments. The combination of these characteristics makes the Murray 465609x24A a leading choice in its category, appealing to both professional and industrial users alike.
Top Page Image Contents