Murray 465609x24A manual Trouble Shooting Chart

Page 35

TROUBLE SHOOTING CHART

PROBLEM: The engine will not start.

1.Follow the steps, “How To Start The Engine” in this book.

2.Electric–Start Models: Clean the battery terminals. Tighten the cables.

3.Drain the fuel tank. Clean the fuel line. Replace the fuel filter.

4.Remove the spark plug(s). Move the throttle to the SLOW posi- tion. Turn the ignition key to the ON position. Try to start the en- gine several times. Install the spark plug.

5.Replace the spark plug.

6.Adjust the carburetor.

PROBLEM: The engine will not turn over.

1.Follow the steps, “How To Start The Engine” in this book.

2.Electric–Start Models: Check the level of the acid in the battery. If needed, add water. Charge the battery.

3.Replace the fuse.

4.Check the wiring harness for damage or a loose connection. Repair the damaged wire.

5.Electric–Start Models: replace the solenoid. Recoil–Start Mod-

els: replace the module.

PROBLEM: The engine is difficult to start.

1.Adjust the carburetor.

2.Replace the spark plug.

3.Replace the fuel filter.

PROBLEM: The engine does not run smooth or has a loss of power.

1.Check the oil.

2.Clean the air filter.

3.Clean the air screen.

4.Replace the spark plug.

5.The engine is working too hard. Use a lower gear.

6.Adjust the carburetor.

7.Replace the fuel filter.

PROBLEM: The engine does not run smooth at fast speed.

1.Replace the spark plug.

2.Adjust the throttle control.

3.Clean the air filter.

4.Replace the fuel filter.

PROBLEM: The engine stops when the blades are engaged.

1.To activate the seat sensor, always sit in the middle of the seat.

2.Check the wiring harness for damage or a loose connection. Repair the damaged wire.

PROBLEM: On slopes, the engine stops.

1.Mow up and down slopes. Never mow across a slope.

2.To activate the seat sensor, always sit in the middle of the seat.

PROBLEM: The engine will not idle.

1.Replace the spark plug.

2.Clean the air filter.

3.Adjust the carburetor.

4.Adjust the throttle control.

5.Drain the fuel tank. Clean the fuel line. Replace the fuel filter.

PROBLEM: A hot engine causes a decrease in power.

1.Clean the air screen.

2.Check the oil.

3.Adjust the carburetor.

4.Replace the fuel filter.

PROBLEM: Excessive vibration.

1.Replace the blade.

2.Check for loose engine bolts.

3.Decrease the air pressure in the tires.

4.Adjust the carburetor.

5.Check for a damaged belt or damaged pulley. Replace the damaged parts.

PROBLEM: The grass does not discharge correctly.

1.Stop the engine. Clean the mower housing.

2.Raise the height of cut.

3.Replace or sharpen the blade(s).

4.Move the shift lever to a slower speed.

5.Move the throttle control to the FAST position.

6.Replace the spring for the blade idler.

PROBLEM: The mower housing does not cut level.

1.Check the air pressure in the tires.

2.Adjust the level of the mower housing.

3.Check the front axle. If the front axle does not freely pivot, loos- en the axle bolt(s).

PROBLEM: The mower blades will not rotate.

1.Check the mower drive belt. Make sure the belt is installed cor- rectly.

2.Replace the mower drive belt.

PROBLEM: The unit will not move when the brake is released and the speed control pedal is depressed.

1.Check the motion drive belt. Make sure the belt is installed correctly.

2.Adjust the clutch.

3.Replace the motion drive belt.

4.Release the Automatic Drive Disconnect under the seat.

PROBLEM: The unit moves slower or stops when the speed control pedal is depressed.

1.Adjust the clutch.

2.Replace the motion drive belt.

PROBLEM: When the brake pedal is released, belt noise can be heard.

1.Temporary belt noise does not change the operation of the unit. If belt noise is continuous, check the routing of the belt. Make sure the belt is inside all belt guides.

2.If the noise is continuous, adjust the clutch.

PROBLEM: The rear wheels spin over uneven terrain.

1.Check the front axle. If the front axle does not freely pivot, loos- en the axle bolt(s).

F–030758L

35

Page 34 Page 36
Image 35
Page 34 Page 36
Contents Model Table of Contents Safe Operation Practices for Ride-on Mowers OWNER’S InformationEnvironmental Awareness II. Slope operation Safe Mowing Guide Safe Mowing Guide Safe Mowing Guide Before Mowing Steps to FollowControl And Operating Pictorials Safety Warning PictorialsInternational Pictorials International PictorialsAssembly AssemblyHOW to Assemble the Gauge Wheels HOW to Install the SeatHOW to Assemble the Steering Wheel Attach the extension spring to the blade control rod. Make HOW to Install the Mower HousingRemove the battery and battery tray Maintenance Free BatteryHOW to Charge Maintenance Free Battery HOW to Install the Battery CablesCheck the Tires HOW to Prepare the EngineCheck the Level of the Mower Housing IMPORTANT! Before YOU Start MowingLocation of Controls OperationAttachments HOW to USE the Throttle ControlTo 2/3 HOW to USE the Speed Control PedalHOW to Disconnect the Transmission To 1/2HOW to Transport the Unit HOW to SET the Parking BrakeHOW to Change the Cutting Height HOW to Stop the UnitHOW to Operate the Unit on Hills HOW to Operate with the Mower HousingCarburetor HOW to Start the EngineBefore Starting the Engine Mowing and Bagging Tips Operating TipsGeneral Recommendations MaintenanceFrequency Maintenance Required Comments HOW to Check the MufflerMount the blade and blade adapter on the mandrel HOW to Remove and Install the BladeHOW to Sharpen the Blade Inspect BladeHOW to Adjust the Blade Rotation Control Remove the 1/4 inch 6 mm pin or bolt Figure HOW to Check and Adjust the Motion Drive BeltDisconnect the red cable from the positive + terminal HOW to Check and Adjust the Drive BrakeHOW to Check the Fuel Filter Where to LubricateAttach the extension spring to the blade control rod. See HOW to Remove the Mower HousingRemove the mower drive belt from the stack pulley 5,6 HOW to Adjust the Gauge WheelsLift Lever Hole No Position No HOW to Level the Mower Housing Remove the mid-idler pulley HOW to Replace the Motion Drive BeltInstall the mid-idler pulley Remove the primary mower drive belt from the stack pulley HOW to Replace the Primary Mower Drive BeltHOW to Replace the Secondary Mower Drive Belt Assemble the left pulley coverFasten the rear wheel with washer and e-ring HOW to Install the WheelsBattery HOW to Replace the FuseHOW to Replace the Light Bulb HOW to Clean the Mower HousingTrouble Shooting Chart USA 030758L030758L Chassis & Hood Repair PartsKey Description Drive Assembly Drive Assembly Steering Repair Parts Mower Housing Suspension Repair Parts Mower Housing 7601031 Repair Parts Engine Mount Assembly Engine Mount Assembly Repair Parts Electrical System Key Part Description Electrical System030758L 030758L 030758L Index Model No Bushel Capacity Model No

465609x24A specifications

Murray 465609x24A is a versatile and robust equipment designed for a variety of applications, particularly in the fields of agriculture and industrial use. Engineered for durability and efficiency, this model is built to withstand rigorous conditions while providing high performance.

One of the standout features of the Murray 465609x24A is its powerful engine. It is equipped with a state-of-the-art propulsion system that ensures maximum output with minimal fuel consumption. The engine's advanced technology allows for smooth operation, whether it's powering through tough terrains or handling heavy loads. This makes it ideal for users who demand reliability in challenging environments.

In addition to its powerful engine, the 465609x24A incorporates advanced safety features which are paramount for both operator protection and equipment longevity. An integrated sensor system continuously monitors the machine’s performance, automatically adjusting parameters to prevent overheating and maintain optimal working conditions. This technology not only enhances safety but also extends the lifespan of the equipment.

The design of the Murray 465609x24A is fundamentally user-centric. It features an ergonomic layout that allows for ease of operation. The controls are intuitively placed, enabling operators to manage tasks efficiently without unnecessary complication. The spacious cabin allows for extended use without compromising comfort, which is essential during long workdays.

Furthermore, the 465609x24A includes a versatile attachment system, accommodating a wide range of tools and implements. This adaptability enhances its functionality, allowing users to tailor the machine according to specific tasks—whether it’s plowing, lifting, or transporting materials.

Maintenance is simplified with the Murray 465609x24A. The design includes easy access points for routine checks, making it straightforward for operators to conduct maintenance tasks. This emphasis on serviceability ensures that the machine remains in peak operational condition, reducing downtime and increasing productivity.

In conclusion, the Murray 465609x24A stands out as a reliable, efficient, and adaptable piece of machinery. With its powerful engine, robust safety features, user-friendly design, and easy maintenance, it is a formidable choice for those in need of a dependable workhorse in demanding environments. The combination of these characteristics makes the Murray 465609x24A a leading choice in its category, appealing to both professional and industrial users alike.
Top Page Image Contents