Craftsman 917.28726 owner manual Tires, Blade Removal

Page 18

TRACTOR

Always observe safety rules when per- forming any maintenance.

BRAKE OPERATION

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced. (See "TO CHECK BRAKE" in the Service and Adjustments section of this manual).

TIRES

•Maintain proper air pressure in all tires

(See PSI on tires).

,Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may

cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM AND

REVERSE OPERATION SYSTEM (ROS) Be sure operator presence and reverse operation systems are working properly. If your tractor does not function as de- scribed, repair the problem immediately.

•The engine should not start unless the brake pedal is fully depressed, and the attachment clutch control is in the disen-

gaged position.

CHECK OPERATOR PRESENCE

SYSTEM

,When the engine is running, any at- tempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

,When the engine is running and the attachment clutch is engaged, any at- tempt by the operator to leave the seat should shut off the engine.

,The attachment clutch should never op- erate unless the operator is in the seat.

ROS "ON" Position Engine "ON" Position (Normal Operating)

CHECK REVERSE OPERATION (ROS) SYSTEM

,When the engine is running with the ignition switch in the engine "ON" posi- tion and the attachment clutch engaged, any attempt by the operator to drive in reverse should shut off the engine.

•When the engine is running with the ignition switch in the ROS "ON" position and the attachment clutch engaged, any attempt by the operator to drive in

reverse should NOT shut off the engine.

BLADE CARE

For best results mower blades must be

sharp. Replace worn, bent or damaged blades.

CAUTION: Use only a replacement

blade approved by the manufacturer of your tractor. Using a blade not approved

by the manufacturer of your tractor is hazardous, could damage your tractor and void your warranty.

BLADE REMOVAL

1.Raise mower to highest position to al- low access to blades.

NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth.

2.Remove blade bolt by turning counter- clockwise.

3.Install new blade with stamped

"GRASS SIDE" facing the ground. iMPORTANT." To ensure proper assembly, center hole in blade must align with star on mandrel assembly.

4.Install and tighten blade bolt securely

(45-55 Ft. Lbs. torque).

iMPORTANT: Special blade bolt is heat treated.

Blade

Mandrel

Blade BoltAssembly (S_

Center Hole

BATTERY

Your tractor has a battery charging system which is sufficient for normal use. How-

ever, periodic charging of the battery with an automotive charger will extend its life.

,Keep battery and terminals clean.

,Keep battery bolts tight.

•Keep small vent holes open.

•Recharge at 6-10 amperesfor 1 hour. NOTE: The original equipment battery on

your tractor is maintenance free. Do not

attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Rrftsmrn SEARS, Roebuck and CO., Hoffman ESTATES, IL 60179 U.S.A90=DAYS on Battery Year on TractorGeneral Operation IV. Towing ServiceII. Slope Operation Safe Handling of GasolineGeneral Service Not use a nozzle lock-opendeviceProduct SPECiFiCATiONSSears Installation Service For prices and additional information call 1=800=827=6655Check Battery Adjust SeatUnpack Carton Check Deck Levelness To Drive Tractor OFF SkidCheck Tire Pressure Check Brake System@@@ Service Reminder / Hour Meter Know Your TractorAttachment Clutch Lever Stopping To Adjust Mower Cutting Height To Operate MowerTo Transport Using the Reverse Operation SystemTo Operate on Hills Transmission Engaged Transmission DisengagedADD Gasoline Towing Carts and Other Attach MentsBefore Starting the Engine Check Engine OIL Level To Start EngineAutomatic Transmission Warm UP RGE TRANSMiSSiONMowing TiPS Maintenance ScheduleGeneral Recommendations Tires Blade RemovalBelts LubricationTo Change Engine OIL AIR Filter To Install Mower To Remove Mower03042 FRONT-TO-BACK Adjustment Precision SIDE-TO-SIDE AdjustmentVisual SIDE-TO-SIDE Adjustment To Level MowerTo Replace Mower Drive Belt Front Wheel TOE-IN/CAMBER To Start Engine with a Weak BAT- TeryTo Remove CABLES, Reverse Order Engine To Adjust Choke Control To Adjust CarburetorEngine OIL BatteryFuel System CylindersProblem Cause Correction Into reverse =ROBLEM Cause CorrectionVibration Operator leaves seat withRoblem Cause Correction Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXGarantia Servicio Funcionamiento General De amputar las manosy los pies y de lanzarIII. Niios IV. RemolquePage Especificaciones DEL Producto API-SG-SLResponsabilidades DEL Cliente LA Caja DE Carton Ajuste EL AsientoPara Remover EL Tractor Desempaque LA Caja DE CartonRevision DE LA Preskn DE LAS Llantas Revision DE LA Nivelacion DELRemover EL Tractor DE LA Plata Conjunto@@@ Palanca DE Control DE Movimien Familiaricese CON SU TractorSU Tractor Palanca DE Mando CruceroParada Cuchillas DE LA Segadora Como Usar SU TractorMiento Para Usar EL Control DE LA AOELER- AOI6N DPara Ajustar LA Altura DE Corte DE LA Segadora AtrasUtilizar EL Mando Crucero Para Ajustar LAS Ruedas CALIBRADO- RASPara Operar EN Cerros Usar EL Sistema DE Funcionamiento AtrasPara Transportar Meoanismo DE Aviso DE Servicio / CRON6METRO Antes DE Hacer Arrancar EL MotorAgregue Gasolina Arranque CON Tiempo FRO 50 Y Menos MASArranque CON Tiempo Templado Calentamiento Para LA Transmision AutomaticaConsejos Para Segar Programa DE Mantenimiento Recomendaciones GeneralesAntes DE Cada USO Verifiez Sistema Funcionamiento Atras ROS LlantasVerifiez Sistema Presencia OPERA- DOR Cuidado DE LA CuohillaCorreas Enfriamiento DEL TransejeNivel DEL Fluido DE LA Bomba DEL Transeje Motor LubricacionPara Darle Servicio AL Prefiltro Filtro DE Aceite DEL MotorFiltro DE Aire Para Darle Servicio AL CartuchoTractor Para Desmontar LA Cortadora DE CespedInstale LA Segadora Fije LA Pieza DE Union Anterior E Lado Para Nivelar LA SegadoraRegulacion Visual DE Lado a Lado Ajuste DE Delante a AtrasMontaje DE LA Correa DE Transmision DE LA Segadora Desmontaje DE LA CorreaMontaje DE LA Correa IMPRESI6N / INCLINACI6N DE LAS RUE= Controlar Y Ajustar EL FrenoControl DEL Freno DAS DelanterasPara Cambiar LA Bombilla DE LA LUZ Delantera Para Adjuntar LOS Cables DE EmpalmeReemplazar LA Bateria Para Cambiar EL FusibleMotor Para Ajustar EL Cable DE Control DE LA ACELERACI6NPara Ajustar EL Carburador Cjlindros BaterjaAceite DEL Motor OtrosPero noarranca IDENTIFICACI6N DE ProblemasProblema CausaCuando el operador ContinuadoCORRECCJ6N Ma corte=dieparejoCausa Correccion Solamente Ande Cuesta Arriba O 15GRADOSMAXSears

917.28726 specifications

The Craftsman 917.28726 is a lawn tractor designed for both residential and light commercial use, making lawn maintenance a breeze. This robust machine is packed with features and technologies that enhance its performance, ease of use, and overall functionality.

One of the standout features of the Craftsman 917.28726 is its powerful engine. Equipped with a reliable 20 HP Briggs & Stratton motor, this tractor provides ample power to tackle tough mowing conditions and challenging terrains. Its automatic transmission allows for smooth acceleration and deceleration, making it ideal for users of all experience levels.

The 917.28726 comes with a 42-inch cutting deck, which is designed to handle medium to large lawns effectively and efficiently. The cutting height can be easily adjusted, providing versatility to manage different grass lengths. This feature ensures a clean and even cut, promoting the health and aesthetics of your lawn.

Another important characteristic of the Craftsman 917.28726 is its user-friendly design. The seat features a comfortable cushioning system and ergonomic armrests, making long mowing sessions much more enjoyable. The easy-to-reach controls are intuitively designed, allowing users to quickly adjust settings without interrupting their mowing rhythm.

Safety is also a priority with the Craftsman 917.28726. It is equipped with a safety switch that prevents operation when the operator is not in the seat, reducing the risk of accidents. Moreover, the tractor's strong build quality, reinforced frame, and reliable braking system provide peace of mind while operating on inclines or uneven surfaces.

The tractor also integrates modern technologies such as a quick-connect deck wash system, which simplifies maintenance and keeps the cutting deck clean for optimal performance. The heavy-duty tires provide excellent traction, ensuring stability on various terrains.

In conclusion, the Craftsman 917.28726 combines power, efficiency, and user-friendly features, making it an excellent choice for homeowners and light commercial users. With its durable construction, versatile cutting options, and safety enhancements, this lawn tractor stands out in the market, providing a reliable solution to meet your lawn care needs. Whether you are tackling your backyard or maintaining a larger property, the Craftsman 917.28726 delivers performance and reliability in every cut.
Top Page Image Contents