Craftsman 917.275283 owner manual Automatictransmissionwarmup

Page 14

NOTE: Beforestarting,read the warm and cold starting proceduresbelow.

6.Insert keyinto ignition and turn key clockwiseto start positionand release keyas soon as enginestarts. Do not run starter continuouslyfor more than fifteen secondsper minute.If the enginedoes not start after several attempts,push chokecontrol in, wait a few minutesand try again. If engine still does not start, pullthe chokecon- trol out and retry.

WARMWEATHERSTARTING(50° F and above)

7.When engine starts,slowlypush choke control in untilthe engine begins to run smoothly.If the enginestarts to run roughly,pullthe chokecontrolout slightlyfor a fewsecondsand then continueto push the control in slowly.

•The attachmentsand grounddrive can now be used.If the engine does not acceptthe load, restartthe engine and

allow it to warm up for one minuteusing the chokeas describedabove.

COLD WEATHERSTARTING(50° F and below)

7.When engine starts,slowlypush choke

control in untilthe engine begins to run smoothly.Continueto pushthe choke control in smallsteps allowingthe en- gine to accept small changes in speed and load, untilthe choke controlis fully in. If the engine starts to run roughly,

pull the chokecontrol out slightlyfor a few secondsand then continueto

push the control in slowly.This may requirean enginewarm-upperiod from severalsecondsto severalminutes,

dependingon the temperature. NOTE: In extremecold conditions,if

enginewill notstart you mayneedto dis- engagethe motiondrive belt as follows:

1.Besure parkingbrake is engaged.

2.Removeretainerspringfrom the drive belt tensionhandleto relievebelt ten- sion.

3.Start engineand allow it to warm up for three (3) minutes.

4.Shut-offengine and engageparking brake.

5.Engagedrive belt tensionhandleand replacethe retainerspring.

AUTOMATICTRANSMISSIONWARMUP

Beforedriving the unit in cold weather,

the transmissionshould be warmedup as follows:

1.Be sure the tractor is on levelground.

2.Placethe motioncontrol leverin

neutral.Releasethe parking brakeand let the brakeslowlyreturnto operating position.

3.Allowone minutefortransmissionto

warm up.This can be doneduring the enginewarm up period.

•The attachmentscan be used during the engine warm-upperiodafter the

transmissionhas beenwarmed up and mayrequirethe choke controlbe pulled out slightly.

NOTE: If at a highaltitude (above3000 feet) or in cold temperatures(below32 F) the carburetorfuel mixturemay needto be adjustedfor best engineperformance. (See "TOADJUSTCARBURETOR"in the Serviceand Adjustmentssection of this manual).

PURGE TRANSMISSION

_CAUTION: Neverengage or disengage freewheelleverwhilethe engineis run- ning.

Toensureproperoperationand per- formance,it is recommendedthat the

transmissionbe purged beforeoperating tractorfor the first time.This procedurewill removeany trappedair insidethe trans- missionwhichmay havedevelopedduring shippingof your tractor.

IMPORTANT: Should your transmission require removalfor service or replace- ment, it should be purged after reinstall- ation beforeoperatingthe tractor.

1.Placetractor safely on levelsurface with engine off and parking brakeset.

2.Disengagetransmissionby plac- ing freewheelcontrolin disengaged position (See"TOTRANSPORT'in this sectionof manual).

3.Sitting in the tractorseat, start engine. After the engine is running, move throttlecontrolto slow position.Disen- gage parkingbrake.

4.Move motioncontrol leverto full

forwardpositionand hold for five (5) seconds.Move leverto full reverse

positionand holdfor five (5) seconds. Repeatthis procedurethree (3)times.

NOTE: Duringthis stepthere will be no movementof drive wheels.The air is being removedfrom hydraulicdrive system.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents NFTZMnNl Limited Warranty on Craftsman Riding Equipment Limited Warranty on BatteryGeneral Operation II. Slope OperationIV. Service Do notUnleaded Type Product SpecificationsGallons Above 32F SAE 5W-30 Below 32FRepair Protection Sears Installation ServiceCustomer Responsibilities AgreementsTo Remove Tractor from HOW to SET UP Your TractorCheck Battery Unpack CartonCheck for Proper Position of ALL Belts Check Deck LevelnessChecktire Pressure Check Brake SystemH L I.,I Know Your Tractor Engine HOW to USE Your TractorTo SET Parking Brake To USE Choke ControlTo Operate on Hills To Operate MowerTo Stop Mower Blades ADD Gasoline Transmission En Transmission DisengagedBefore Starting the Engine Check Engine OIL Level To Start EngineAutomatictransmissionwarmup Mowing Tips Lubricate General RecommendationsBefore Each USE Battery Blade CareBelts TransaxlecoolingTransaxle Pump Fluid EngineAIR Filter Lower mower to its lowest position To Install MowerTractor To Remove Mower Alternate SIDE-TO-SIDE Adjustment Method To Level Mower HousingSIDE-TO-SIDE Adjustment with Bubble Level Mower Drive Belt Removal Mower Drive Belt InstallationTo Replace Mower Drive Belt To Replace Mower Blade SEC Ondary Drive Belt Install NEW Mower Blade Secondary Drive BeltReinstall Mower Drive Belt Remove Mower Drive BeltTo Replace Motion Drive Belt To Adjust Attachment ClutchTo Check and Adjust Brake To Remove Wheel for Repairs Transmission Removal ReplacementFront Wheel TOE-IN/CAMBER To Start Engine with a Weak BAT- TeryTo Remove Hood and Grill AS- Sembly Replacing BatteryTo Replace Headlight Lamp To Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control Preliminary SettingAcceleration Test Fuel System EngineRemove mower from tractor for winter Engine OILCause Correction Troubleshooting ChartProblem Engine Continues ExcessiveVibration To run whenProblem Cause Correction Tractor -- Model Number Schematic =FR , .,,, LECTR,CCLUTTractor -- Model Number Electrical KEY Part Description J13o Tractor -- Model Number 917.275283 Chassis and EnclosuresKEY Part Description Tractor -- Model Number Ground Drive KEY Part NO. NO.DESCRIPTION 47\ Tractor -- Model Number SteeringKEY Part Description Tractor -- Model Number EngineTractor -- Model Number Lift Assembly LiftVgtTractor -- Model Number Seat Assembly Wheels and Tires Tractor Model Number DecalsTractor -- Model Number Mower Deck Inches 1 inch = ¢,0 Tractor -- Model Number TRANSAXLE-MODEL Number 125THK\31 fJ HEAD/VALVE/BREATHER Crankcase KEY Part NO. no IGNITION/ELECTRICAL Blower Housing and Baffles IGNITION/ELECTRICAL Starting System J Engine Controls J Starting System OIL PAN/LUBRICATION KEY Part Description Exhaust J Crankshaft KEY Part Description Page Suggested Guide for Sighting Slopes for Safe Operation Get it fixed, at your home or ourst

917.275283 specifications

The Craftsman 917.275283 is a premium lawn tractor designed for homeowners seeking a reliable and efficient machine for maintaining their lawns. Built with a robust structure and advanced engineering, this lawn tractor offers a perfect blend of performance, comfort, and user-friendly features.

At the heart of the Craftsman 917.275283 is a powerful 24 HP Briggs & Stratton engine that ensures ample power for mowing, mulching, and hauling tasks. This engine is coupled with a hydrostatic transmission, providing smooth and effortless speed control while driving on various terrains. Operators can easily adjust their speed without the need for shifting gears, making it an ideal choice for those looking for convenience during their mowing sessions.

One of the standout features of this lawn tractor is its 42-inch cutting deck. This deck is designed to provide a wide cutting path, effectively reducing the number of passes needed to cover a lawn. The cutting height is adjustable, allowing users to customize the grass height according to their preference, resulting in a healthier and more aesthetically pleasing lawn. Additionally, the deck is crafted for easy cleaning, ensuring that maintenance is straightforward.

The Craftsman 917.275283 also incorporates advanced technology for enhanced mowing precision. The onboard SmartCut technology automatically adjusts the engine speed based on the grass thickness, allowing for optimal cutting efficiency. This feature not only improves performance but also extends engine life by reducing strain during operation.

Comfort is a key aspect of any lawn care equipment, and Craftsman does not disappoint. The tractor features an ergonomic seat with ample padding, ensuring a comfortable ride even during extended mowing sessions. The easy-to-reach controls are designed to prevent fatigue, allowing users to focus on their mowing tasks.

Safety features are also integrated into the design of the Craftsman 917.275283. The tractor comes equipped with a safety key, ensuring that the engine cannot be started while in gear. This is a critical feature that provides peace of mind, especially for those with children or pets nearby.

In summary, the Craftsman 917.275283 stands out in the market of lawn tractors with its powerful engine, user-friendly hydrostatic transmission, and advanced cutting technologies. Coupled with a comfortable design and essential safety features, this machine is tailored to meet the needs of homeowners looking to achieve a perfectly manicured lawn with ease and efficiency.
Top Page Image Contents