Craftsman 917.275283 owner manual Transmission Removal Replacement, Front Wheel TOE-IN/CAMBER

Page 25

Retainer

Spring

Driv(

Tension

Handle

Engine Pulley

Transaxle Pulley

Belt

 

 

Belt

Keeper

 

 

Keeper

V-Idler

Keeper

Clutching

Clutching

Flat Idler

 

 

Idler

 

TRANSAXLE MOTION CONTROL LE-

VER NEUTRAL ADJUSTMENT

The motion control lever has been preset at the factory and adjustment should not be necessary.

1.Park Tractor on level surface. Stop tractor by turning ignition key to "OFF" position and engage parking brake.

2.Loosen the adjustment bolt in front of the right rear wheel.

3.Move motion control lever to the neu- tral position.

4.Tighten the adjustment bolt.

Adjustment Bolt

TRANSMISSION REMOVAL/

REPLACEMENT

Should your transmission require removal for service or replacement, it should be purged after reinstallation and before op- erating the tractor. See "PURGE TRANS- MISSION" in the Operation section of this manual.

TO ADJUST STEERING WHEEL ALIGN-

MENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble with crossbars horizontal. Tighten securely.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not

adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or

camber, contact a Sears or other qualified service center.

TO REMOVE WHEEL FOR REPAIRS

FRONT WHEEL -

1.Block up axle securely.

2.Remove axle cover, retaining ring and washers to allow wheel removal.

3.Repair tire and reassemble.

4.Replace washers and snap retaining ring securely in axle groove.

5.Replace axle cover.

REAR WHEEL -

1.Block rear axle securely.

2.Remove five (5) lug nuts to allow wheel removal.

3.Repair tire and reassemble. Replace and tighten lug nuts securely.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, purchase and use tire sealant from Sears. Tire sealant also prevents tire dry rot and corrosion.

Washers

Retaining

Ring

Axle

Cover

00663

TO START ENGINE WITH A WEAK BAT- TERY

_WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from bat- teries. Always wear eye protection when around batteries.

If your battery is too weak to start the

engine, it should be recharged. (See "BAT- TERY" in the MAINTENANCE section of

this manual).

If "jumper cables" are used for emergency starting, follow this procedure:

IMPORTANT: Your tractor is equipped with a 12 volt system. The other vehicle must also be a 12 volt system. Do not use your tractor battery to start other vehicles.

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents NFTZMnNl Limited Warranty on Battery Limited Warranty on Craftsman Riding EquipmentII. Slope Operation General OperationDo not IV. ServiceGallons Product SpecificationsUnleaded Type Above 32F SAE 5W-30 Below 32FCustomer Responsibilities Sears Installation ServiceRepair Protection AgreementsCheck Battery HOW to SET UP Your TractorTo Remove Tractor from Unpack CartonChecktire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemH L I.,I Know Your Tractor To SET Parking Brake HOW to USE Your TractorEngine To USE Choke ControlTo Stop Mower Blades To Operate MowerTo Operate on Hills Before Starting the Engine Check Engine OIL Level Transmission En Transmission DisengagedADD Gasoline To Start EngineAutomatictransmissionwarmup Mowing Tips Before Each USE General RecommendationsLubricate Blade Care BatteryTransaxle Pump Fluid TransaxlecoolingBelts EngineAIR Filter Tractor To Remove Mower To Install MowerLower mower to its lowest position SIDE-TO-SIDE Adjustment with Bubble Level To Level Mower HousingAlternate SIDE-TO-SIDE Adjustment Method To Replace Mower Drive Belt Mower Drive Belt InstallationMower Drive Belt Removal Reinstall Mower Drive Belt Install NEW Mower Blade Secondary Drive BeltTo Replace Mower Blade SEC Ondary Drive Belt Remove Mower Drive BeltTo Check and Adjust Brake To Adjust Attachment ClutchTo Replace Motion Drive Belt Front Wheel TOE-IN/CAMBER Transmission Removal ReplacementTo Remove Wheel for Repairs To Start Engine with a Weak BAT- TeryTo Replace Headlight Lamp Replacing BatteryTo Remove Hood and Grill AS- Sembly To Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor Preliminary SettingAcceleration Test Remove mower from tractor for winter EngineFuel System Engine OILProblem Troubleshooting ChartCause Correction Vibration ExcessiveEngine Continues To run whenProblem Cause Correction =FR , .,,, LECTR,CCLUT Tractor -- Model Number SchematicTractor -- Model Number Electrical KEY Part Description Tractor -- Model Number 917.275283 Chassis and Enclosures J13oKEY Part Description Tractor -- Model Number Ground Drive KEY Part NO. NO.DESCRIPTION Tractor -- Model Number Steering 47\KEY Part Description Engine Tractor -- Model NumberLiftVgt Tractor -- Model Number Lift AssemblyTractor -- Model Number Seat Assembly Tractor Model Number Decals Wheels and TiresTractor -- Model Number Mower Deck Inches 1 inch = ¢,0 125THK Tractor -- Model Number TRANSAXLE-MODEL Number\31 fJ HEAD/VALVE/BREATHER Crankcase KEY Part NO. no IGNITION/ELECTRICAL Blower Housing and Baffles IGNITION/ELECTRICAL Starting System J Engine Controls J Starting System OIL PAN/LUBRICATION KEY Part Description Exhaust J Crankshaft KEY Part Description Page Suggested Guide for Sighting Slopes for Safe Operation Get it fixed, at your home or ourst

917.275283 specifications

The Craftsman 917.275283 is a premium lawn tractor designed for homeowners seeking a reliable and efficient machine for maintaining their lawns. Built with a robust structure and advanced engineering, this lawn tractor offers a perfect blend of performance, comfort, and user-friendly features.

At the heart of the Craftsman 917.275283 is a powerful 24 HP Briggs & Stratton engine that ensures ample power for mowing, mulching, and hauling tasks. This engine is coupled with a hydrostatic transmission, providing smooth and effortless speed control while driving on various terrains. Operators can easily adjust their speed without the need for shifting gears, making it an ideal choice for those looking for convenience during their mowing sessions.

One of the standout features of this lawn tractor is its 42-inch cutting deck. This deck is designed to provide a wide cutting path, effectively reducing the number of passes needed to cover a lawn. The cutting height is adjustable, allowing users to customize the grass height according to their preference, resulting in a healthier and more aesthetically pleasing lawn. Additionally, the deck is crafted for easy cleaning, ensuring that maintenance is straightforward.

The Craftsman 917.275283 also incorporates advanced technology for enhanced mowing precision. The onboard SmartCut technology automatically adjusts the engine speed based on the grass thickness, allowing for optimal cutting efficiency. This feature not only improves performance but also extends engine life by reducing strain during operation.

Comfort is a key aspect of any lawn care equipment, and Craftsman does not disappoint. The tractor features an ergonomic seat with ample padding, ensuring a comfortable ride even during extended mowing sessions. The easy-to-reach controls are designed to prevent fatigue, allowing users to focus on their mowing tasks.

Safety features are also integrated into the design of the Craftsman 917.275283. The tractor comes equipped with a safety key, ensuring that the engine cannot be started while in gear. This is a critical feature that provides peace of mind, especially for those with children or pets nearby.

In summary, the Craftsman 917.275283 stands out in the market of lawn tractors with its powerful engine, user-friendly hydrostatic transmission, and advanced cutting technologies. Coupled with a comfortable design and essential safety features, this machine is tailored to meet the needs of homeowners looking to achieve a perfectly manicured lawn with ease and efficiency.
Top Page Image Contents