Craftsman 917.274762 owner manual Battery

Page 20

NOTE: Do not use a nailfor balancing blade. The lobesof the center hole may appear to be centered,but are not.

Slideblade on to an unthreadedportion of the steel bolt or pin and holdthe bolt or pin parallelwith the ground. If blade is balanced,it should remainin a horizontalposition. If either endof the blade movesdownward,sharpen the heavyend until the blade is balanced.

. //

5/8" Bolt or Pi_

Blade

Center Hole

BATTERY

Your tractor has a battery charging system which is sufficient for normal use. How-

ever, periodic charging of the battery with an automotive charger will extend its life.

Keep battery and terminals clean.

Keep battery bolts tight.

Keep small vent holes open.

Recharge at 6-10 amperes for 1 hour. NOTE: The original equipment battery on your tractor is maintenance free. Do not

attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.

TO CLEAN BATTERY AND TERMINALS Corrosion and dirt on the battery and terminals can cause the battery to "leak" power.

1.Disconnect BLACK battery cable first then RED battery cable and remove battery from tractor.

2.Rinse the battery with plain water and dry.

3.Clean terminals and battery cable ends with wire brush until bright.

4.Coat terminals with grease or petro- leum jelly.

5.Reinstall battery (See "REPLACING BATTERY" in the Service and Adjust- ments section of this manual).

TRANSAXLE COOLING

The transmission fan and cooling fins should be kept clean to assure proper cooling.

Do not attempt to clean fan or transmis- sion while engine is running or while the transmission is hot. To prevent possible

damage to seals, do not use high pressure water or steam to clean transaxle.

Inspect cooling fan to be sure fan blades are intact and clean.

Inspect cooling fins for dirt, grass clip- pings and other materials. To prevent damage to seals, do not use com- pressed air or high pressure sprayer to

clean cooling fins.

TRANSAXLE PUMP FLUID

The transaxle was sealed at the factory

and fluid maintenance is not required for the life of the transaxle. Should the trans-

axle ever leak or require servicing, contact a Sears or other qualified service center.

V-BELTS

Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary. The belts are not adjustable.

Replace belts if they begin to slip from wear.

ENGINE

LUBRICATION

Only use high quality detergent oil rated with API service classification SG-SL. Se-

lect the oil's SAE viscosity grade according to your expected operating temperature.

SAE VISCOSITY GRADES

F

+20

0

30

32

40

60

80

100

c +_o

+2;

+1;

;

 

1'o _o

1o

4;

TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE

OH VJS_ C_qaFtl

NOTE: Although multi-viscosity oils

(5W30, 10W30 etc.)improve starting in cold weather, they will result in increased oil consumption when used above 32°E Check your engine oil level more frequent- ly to avoid possible engine damage from running low on oil.

Change the oil after every 50 hours of op- eration or at least once a year if the tractor is not used for 50 hours in one year.

Check the crankcase oil level before start- ing the engine and after each eight (8) hours of operation. Tighten oil fill cap/

dipstick securely each time you check the oil level.

TO CHANGE ENGINE OIL

Determine temperature range expected

before oil change. All oil must meet API service classification SG-SL.

Be sure tractor is on level surface.

Oil will drain more freely when warm.

Catch oil in a suitable container.

1.Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine

when changing oil.

2.Remove yellow cap from end of drain valve and install the drain tube onto the

fitting.

20

Image 20
Contents Icrrftsmiihi Sears Craftsman Help LineLimited Warranty on Craftsman Riding Equipment Limited Warranty on BatteryIwarning General OperationSafe Handling of Gasoline ServiceIV, Towi NG General Service Repair Protection Agreements Sears Installation ServiceCustomer Responsibilities Keys Tools Required for Assembly Install Steering WheelInstall Seat Carton Unpack CartonCheck Battery Operation section for locationChecklist Check for Proper Position of ALL BeltsChecktire Pressure Check Deck LevelnessUnlocked Reverse Operation System ROS on Position Allows operation TractorLift Lever Plunger Used to release HOW to USE Your To Adjust Mower Cutting HeightTo SET Parking Brake To Move Forward and BackwardTo Operate Mower To Adjust Gauge WheelsOperating in Reverse To Transport Transmission Engaged Transmission DisengagedTowing Carts and Other Attach Ments ADD GasolineTo Start Engine Automatic Transmission Warm UPTo Transport Mowing TipsGeneral Recommendations ROSTractor Operator Presence System Reverse Operation System ROSBlade Care To Sharpen BladeBattery Engine Cooling System Clean AIR ScreenAIR Filter Cleaning MufflerSpark Plugs IN-LINE Fuel FilterTo Install Mower To Remove MowerTo Level Mower Housing SIDE-TO-SIDE AdjustmentBelt Installation To Replace Mower Blade Drive BeltTo Check and Adjust Brake To Adjust BrakeTo Check Brake To Replace Motion Drive BeltTransaxle Motion Control LE VER Neutral Adjustment Transmission Removal ReplacementMent To Remove Wheel for RepairsReplacing Battery Do not short batteryTo Replace Headlight Bulb To Remove Hood and Grill AS SemblyTo Adjust Throttle Control Cable To Adjust CarburetorPreliminary Setting EngineCylinders Fuel SystemEngine OIL Problem Loss of powerCause Correction StartTroubleshooting Chart Problem Cause CorrectionProblem Cause Correction Schematic Tractor - Model NumberElectrical Electrical KEY Part DescriptionTractor - Model Number 917,274762 Chassis and Enclosures Tractor - Model Number 917.274762 Chassis and Enclosures KEY Part DescriptionTractor - Model Number 917,274762 Ground Drive Tractor Model Number Part DescriptionTractor - Model Number 917,274762 Steering Assembly Tractor - Model Number 917.274762 Steering Assembly Engine Optional Equipment Spark ArresterTractor - Model Number Seat Assembly 180166Decals Wheels TiresTractor - Model Number 917,274762 Lift Assembly 16 1718Tractor - Model Number 917,274762 Mower Deck 15868 185117 119 113Tractor - Model Number Mower Deck TUVZN c O Hydro Transaxle Model Number20@ 616 1127NIKKIJ All component Dimensions Given in U.S. inches Inch = 25.4 mm Set Degrees MAX Only Ride UP and Down HillNot Across Hill Iiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiii Our Home

917.274762 specifications

The Craftsman 917.274762 is a high-performance lawn tractor designed for residential homeowners who prioritize both efficiency and ease of use in their outdoor maintenance tasks. Equipped with a robust 24 HP Kohler engine, the 917.274762 provides ample power for tackling a variety of yard sizes and terrains, ensuring that grass cutting is both swift and efficient. With its reliable engine, this tractor can handle not just mowing but also light towing and hauling tasks around the yard.

One of the standout features of the Craftsman 917.274762 is its 42-inch cutting deck. This mid-sized deck strikes a perfect balance between maneuverability and cutting capability, making it suitable for both small and medium-sized lawns. The deck is equipped with a cutting height adjustment feature that allows users to choose from a variety of settings for a customizable cut, ensuring a clean and precise lawn finish every time. The deck's design promotes optimal grass collection, resulting in minimal clumping and a healthier lawn overall.

The user-friendly design of the tractor enhances the overall mowing experience. The control panel is intuitively placed, offering easy access to start, stop, and speed control features. Furthermore, the tractor features a comfortable, adjustable seat that provides ergonomic support for longer mowing sessions. For added convenience, the Craftsman 917.274762 boasts a tight turning radius, allowing users to navigate around trees, flowerbeds, and other landscape features with ease.

Safety is also a priority in the Craftsman 917.274762. The tractor comes equipped with an automatic blade brake, ensuring that the blades disengage when the operator leaves the seat, reducing the risk of accidents. Additionally, the sturdy construction and durable materials used in the tractor's design promise longevity and resilience against the wear and tear of regular use.

Overall, the Craftsman 917.274762 combines power, versatility, and comfort, making it an excellent choice for homeowners looking to maintain their lawns with ease. Its reliable engine, impressive cutting capabilities, and user-centric features make it a valuable asset in any outdoor toolkit. Whether you are mowing the lawn or tackling more demanding landscaping tasks, this lawn tractor is designed to meet a variety of needs with efficiency and style.