Engine, To Adjust Throttle Control Cable

ENGINE

Maintenance, repair, or replacement of the emission control devices and systems, which are being done at the customers expense, may be performed by any non-road engine repair establishment or individual. Warranty repairs must be performed by an authorized engine manufacturer's service outlet.

TO ADJUST THROTTLE CONTROL

CABLE

The throttle control has been preset at the factory and adjustment should not be nec- essary. Check adjustment as described below before loosening cable. If adjust- ment is necessary, proceed as follows:

1.With engine not running, move throttle control lever from slow to choke posi- tion. Slowly move lever from choke to fast position.

2.Check that holes "A" in governor

control lever and hole in governor plate line-up. If holes "A" are not aligned, loosen clamp screw and move throttle cable until holes are aligned. Tighten clamp screw securely.

Governor Control Lever Governor Control Plate

Holes
"A"	Clamp Screw	Cable
TO ADJUST	CARBURETOR

NOTE: The carburetor on this engine is low emission. It is equipped with an idle

fuel adjusting needle with a limiter cap, which allows some adjustment within the limits allowed by the cap. Do not attempt to remove the limiter cap. The limiter cap cannot be removed without breaking the adjusting needle.

The carburetor has been preset at the factory and adjustment should not be necessary. However, minor adjustment may be required to compensate for differ- ences in fuel, temperature, altitude or load. If the carburetor does need adjustment, proceed as follows:

In general, turning idle mixture valve in (clockwise) decreases the supply of fuel to the engine giving a leaner fuel/air mix- ture. Turning the idle mixture valve out

(counterclockwise) increases the supply

of fuel to the engine giving a richer fuel/air mixture.

IMPORTANT: Damage to the needle

valve and the seat in carburetor may result if screw is turned in too tight.

PRELIMINARY SETTING -

1.Air cleaner assembly must be assem- bled to the carburetor when making carburetor adjustments.

2.Be sure the throttle control cable is adjusted properly (see above).

FINAL SETTING -(See "TO ADJUST THROTTLE CONTROL CABLE" in this

section of the manual.)

1.Start engine and allow to warm for five minutes. Make final adjustments with engine running and shift/motion control lever in neutral (N) position.

2.Move throttle control lever to slow posi- tion. With finger, rotate and hold throttle lever against idle speed screw. Turn idle speed screw to attain 1750 RPM.

3.While still holding throttle lever against idle speed screw, turn idle mixture valve full travel clockwise then counter- clockwise until engine runs rough. Turn valve to a point midway between those two positions. Release throttle lever.

ACCELERATION TEST -

4.Move throttle control lever from slow to fast position. If engine hesitates or dies, turn idle mixture valve out (coun-

terclockwise) 1/8 turn. Repeat test and continue to adjust, if necessary, until

engine accelerates smoothly.

High speed stop is factory adjusted. Do not adjust or damage may result.

IMPORTANT: Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous. If you think the

engine-governed high speed needs adjust- ing, contact a Sears or other qualified ser- vice center, which has proper equipment and experience to make any necessary adjustments.

Idle Speed

Lever

Idle Mixture

Valve with

Limiter

917.274762 specifications

The Craftsman 917.274762 is a high-performance lawn tractor designed for residential homeowners who prioritize both efficiency and ease of use in their outdoor maintenance tasks. Equipped with a robust 24 HP Kohler engine, the 917.274762 provides ample power for tackling a variety of yard sizes and terrains, ensuring that grass cutting is both swift and efficient. With its reliable engine, this tractor can handle not just mowing but also light towing and hauling tasks around the yard.

One of the standout features of the Craftsman 917.274762 is its 42-inch cutting deck. This mid-sized deck strikes a perfect balance between maneuverability and cutting capability, making it suitable for both small and medium-sized lawns. The deck is equipped with a cutting height adjustment feature that allows users to choose from a variety of settings for a customizable cut, ensuring a clean and precise lawn finish every time. The deck's design promotes optimal grass collection, resulting in minimal clumping and a healthier lawn overall.

The user-friendly design of the tractor enhances the overall mowing experience. The control panel is intuitively placed, offering easy access to start, stop, and speed control features. Furthermore, the tractor features a comfortable, adjustable seat that provides ergonomic support for longer mowing sessions. For added convenience, the Craftsman 917.274762 boasts a tight turning radius, allowing users to navigate around trees, flowerbeds, and other landscape features with ease.

Safety is also a priority in the Craftsman 917.274762. The tractor comes equipped with an automatic blade brake, ensuring that the blades disengage when the operator leaves the seat, reducing the risk of accidents. Additionally, the sturdy construction and durable materials used in the tractor's design promise longevity and resilience against the wear and tear of regular use.

Overall, the Craftsman 917.274762 combines power, versatility, and comfort, making it an excellent choice for homeowners looking to maintain their lawns with ease. Its reliable engine, impressive cutting capabilities, and user-centric features make it a valuable asset in any outdoor toolkit. Whether you are mowing the lawn or tackling more demanding landscaping tasks, this lawn tractor is designed to meet a variety of needs with efficiency and style.