Craftsman 917.274762 owner manual Transaxle Motion Control LE VER Neutral Adjustment, Ment

Page 26

EnginePulley

ClutchingIdler_

J_

I

Keeper11_,,_

TRANSAXLE MOTION CONTROL LE-

VER NEUTRAL ADJUSTMENT

The motion control lever has been preset at the factory and adjustment should not be necessary.

1.Loosen adjustment bolt in front of the right rear wheel, and lightly tighten.

2.Start engine and move motion con- trol lever until tractor does not move forward or backward.

3.Hold motion control lever in that posi- tion and turn engine off.

4.While holding motion control lever in place, loosen the adjustment bolt.

5.Move motion control lever to the neutral

(N)(lock gate) position.

6.Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

After above adjustment is made, if the

tractor still creeps forward or backward while motion control lever is in neutral

position, follow these steps:

1.Loosen the adjustment bolt.

2.Move the motion control lever 1/4 to 1/2 inch in the direction it is trying to creep.

3.Tighten adjustment bolt securely.

4.Start engine and test.

5.If tractor still creeps, repeat above steps until satisfied.

Motion

Control

Lever

Lock

.......

Gate

Adjustment

Bolt

TRANSMISSION REMOVAL/

REPLACEMENT

Should your transmission require removal for service or replacement, it should be purged after reinstallation and before operating the

tractor. See "PURGE TRANSMISSION" in the Operation section of this manual.

TO ADJUST STEERING WHEEL ALIGN-

MENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble with crossbars horizontal. Tighten securely.

FRONT WHEEL TOE-IN/CAM BER

The front wheel toe-in and camber are not

adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or

camber, contact a Sears or other qualified service center.

TO REMOVE WHEEL FOR REPAIRS

1.Block up axle securely.

2.Remove axle cover, retaining ring and washers to allow wheel removal (rear wheels have a square key - Do not lose).

3.Repair tire and reassemble.

NOTE: On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

4.Replace washers and snap retaining ring securely in axle groove.

5.Replace axle cover.

NOTE: To seal tire punctures and prevent

flat tires due to slow leaks, purchase and use tire sealant from Sears. Tire sealant

also prevents tire dry rot and corrosion.

Washers

Retaining Ring

Axle Cover

Square Key

/_

-_'

(Rear Wheel

Only) I

 

TO START ENGINE WITH A WEAK BAT- TERY

_,WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from bat-

teries. Always wear eye protection when around batteries.

If your battery is too weak to start the

engine, it should be recharged. (See "BAT-

TERY" in the MAINTENANCE section of this manual).

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Icrrftsmiihi Sears Craftsman Help LineLimited Warranty on Craftsman Riding Equipment Limited Warranty on BatteryIwarning General OperationSafe Handling of Gasoline ServiceIV, Towi NG General Service Repair Protection Agreements Sears Installation ServiceCustomer Responsibilities Keys Install Seat Tools Required for AssemblyInstall Steering Wheel Carton Unpack CartonCheck Battery Operation section for locationChecktire Pressure ChecklistCheck for Proper Position of ALL Belts Check Deck LevelnessUnlocked Reverse Operation System ROS on Position Allows operation TractorLift Lever Plunger Used to release To SET Parking Brake HOW to USE YourTo Adjust Mower Cutting Height To Move Forward and BackwardTo Operate Mower To Adjust Gauge WheelsOperating in Reverse Towing Carts and Other Attach Ments To TransportTransmission Engaged Transmission Disengaged ADD GasolineTo Start Engine Automatic Transmission Warm UPTo Transport Mowing TipsGeneral Recommendations ROSBlade Care TractorOperator Presence System Reverse Operation System ROS To Sharpen BladeBattery Engine Cooling System Clean AIR ScreenAIR Filter Spark Plugs CleaningMuffler IN-LINE Fuel FilterTo Install Mower To Remove MowerBelt Installation To Level Mower HousingSIDE-TO-SIDE Adjustment To Replace Mower Blade Drive BeltTo Check Brake To Check and Adjust BrakeTo Adjust Brake To Replace Motion Drive BeltMent Transaxle Motion Control LE VER Neutral AdjustmentTransmission Removal Replacement To Remove Wheel for RepairsTo Replace Headlight Bulb Replacing BatteryDo not short battery To Remove Hood and Grill AS SemblyPreliminary Setting To Adjust Throttle Control CableTo Adjust Carburetor EngineCylinders Fuel SystemEngine OIL Cause Correction ProblemLoss of power StartTroubleshooting Chart Problem Cause CorrectionProblem Cause Correction Schematic Tractor - Model NumberElectrical Electrical KEY Part DescriptionTractor - Model Number 917,274762 Chassis and Enclosures Tractor - Model Number 917.274762 Chassis and Enclosures KEY Part DescriptionTractor - Model Number 917,274762 Ground Drive Tractor Model Number Part DescriptionTractor - Model Number 917,274762 Steering Assembly Tractor - Model Number 917.274762 Steering Assembly Engine Optional Equipment Spark ArresterTractor - Model Number Seat Assembly 180166Decals Wheels TiresTractor - Model Number 917,274762 Lift Assembly 16 1718117 119 Tractor - Model Number 917,274762 Mower Deck15868 185 113Tractor - Model Number Mower Deck TUVZN c O Hydro Transaxle Model Number20@ 616 1127NIKKIJ All component Dimensions Given in U.S. inches Inch = 25.4 mm Set Degrees MAX Only Ride UP and Down HillNot Across Hill Iiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiii Our Home

917.274762 specifications

The Craftsman 917.274762 is a high-performance lawn tractor designed for residential homeowners who prioritize both efficiency and ease of use in their outdoor maintenance tasks. Equipped with a robust 24 HP Kohler engine, the 917.274762 provides ample power for tackling a variety of yard sizes and terrains, ensuring that grass cutting is both swift and efficient. With its reliable engine, this tractor can handle not just mowing but also light towing and hauling tasks around the yard.

One of the standout features of the Craftsman 917.274762 is its 42-inch cutting deck. This mid-sized deck strikes a perfect balance between maneuverability and cutting capability, making it suitable for both small and medium-sized lawns. The deck is equipped with a cutting height adjustment feature that allows users to choose from a variety of settings for a customizable cut, ensuring a clean and precise lawn finish every time. The deck's design promotes optimal grass collection, resulting in minimal clumping and a healthier lawn overall.

The user-friendly design of the tractor enhances the overall mowing experience. The control panel is intuitively placed, offering easy access to start, stop, and speed control features. Furthermore, the tractor features a comfortable, adjustable seat that provides ergonomic support for longer mowing sessions. For added convenience, the Craftsman 917.274762 boasts a tight turning radius, allowing users to navigate around trees, flowerbeds, and other landscape features with ease.

Safety is also a priority in the Craftsman 917.274762. The tractor comes equipped with an automatic blade brake, ensuring that the blades disengage when the operator leaves the seat, reducing the risk of accidents. Additionally, the sturdy construction and durable materials used in the tractor's design promise longevity and resilience against the wear and tear of regular use.

Overall, the Craftsman 917.274762 combines power, versatility, and comfort, making it an excellent choice for homeowners looking to maintain their lawns with ease. Its reliable engine, impressive cutting capabilities, and user-centric features make it a valuable asset in any outdoor toolkit. Whether you are mowing the lawn or tackling more demanding landscaping tasks, this lawn tractor is designed to meet a variety of needs with efficiency and style.
Top Page Image Contents