Craftsman 917.274762 owner manual To Level Mower Housing, SIDE-TO-SIDE Adjustment, Belt Removal

Page 24

8.Place flat washer and clutch spring on idler pulley bolt and secure with small retainer spring.

9.Install belt onto engine pulley.

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See "PROD-

UCT SPECIFICATIONS" section of this

manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of

mower to ground. Distance "A" on both sides of mower should be the same or within 1/4" of each other.

•If adjustment is necessary, make adjust- ment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift

link adjustment nut on that side.

NOTE: Each full turn of adjustment nut will change mower height about 1/8".

• Recheck measurements after adjusting.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut "E"

on both front links an equal number of turns.

•When distance "D" is 1/8" to 1/2"

lower at front than rear, tighten nuts "F" against trunnion on both front links.

•To raise front of mower, loosen nut"F" from trunnion on both front links. Tighten

nut "E" on both front links an equal num- ber of turns. The two front links must

remain equal in length.

•When distance "D" is 1/8" to 1/2" lower

at front than rear, tighten nut "F" against trunnion on both front links.

•Recheck side-to-side adjustment.

°°• o_° o 01

__Mandrel

Both Front Links Should be ual in Length

Bottom edge

Bottom edge of

of mower to

mower to ground

ground

-_t/

Arm

@

Lift Link N_

Adjustment

FRONT-TO-BACK ADJUSTMENT IMPORTANT: Deck must be level side-to side. If the following front-to-back adjust- ment is necessary, be sure to adjust both front links equally so mower will stay level side-to-side.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its highest position.

Check adjustment on right side of trac- tor. Measure distance "D" directly in front and behind the mandrel at bottom edge of mower housing as shown.

•Before making any necessary adjust- ments, check that both front links are

equal in length.

Front Links

TO REPLACE MOWER BLADE DRIVE

BELT

The mower blade drive belt may be re- placed without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

1.Remove mower from tractor (See "TO REMOVE MOWER" in this section of manual).

2.Work belt off both mandrel pulleys and idler pulleys.

3.Pull belt away from mower.

BELT INSTALLATION -

1.Work belt around both mandrel pulleys and idler pulleys

2.Make sure belt is in all pulley grooves

24 and inside all belt guides.

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Icrrftsmiihi Sears Craftsman Help LineLimited Warranty on Craftsman Riding Equipment Limited Warranty on BatteryIwarning General OperationService IV, Towi NGSafe Handling of Gasoline General Service Sears Installation Service Customer ResponsibilitiesRepair Protection Agreements Keys Tools Required for Assembly Install Steering WheelInstall Seat Carton Unpack CartonCheck Battery Operation section for locationChecklist Check for Proper Position of ALL BeltsChecktire Pressure Check Deck LevelnessUnlocked Tractor Lift Lever Plunger Used to releaseReverse Operation System ROS on Position Allows operation HOW to USE Your To Adjust Mower Cutting HeightTo SET Parking Brake To Move Forward and BackwardTo Adjust Gauge Wheels Operating in ReverseTo Operate Mower To Transport Transmission Engaged Transmission DisengagedTowing Carts and Other Attach Ments ADD GasolineTo Start Engine Automatic Transmission Warm UPTo Transport Mowing TipsGeneral Recommendations ROSTractor Operator Presence System Reverse Operation System ROSBlade Care To Sharpen BladeBattery Clean AIR Screen AIR FilterEngine Cooling System Cleaning MufflerSpark Plugs IN-LINE Fuel FilterTo Install Mower To Remove MowerTo Level Mower Housing SIDE-TO-SIDE AdjustmentBelt Installation To Replace Mower Blade Drive BeltTo Check and Adjust Brake To Adjust BrakeTo Check Brake To Replace Motion Drive BeltTransaxle Motion Control LE VER Neutral Adjustment Transmission Removal ReplacementMent To Remove Wheel for RepairsReplacing Battery Do not short batteryTo Replace Headlight Bulb To Remove Hood and Grill AS SemblyTo Adjust Throttle Control Cable To Adjust CarburetorPreliminary Setting EngineFuel System Engine OILCylinders Problem Loss of powerCause Correction StartTroubleshooting Chart Problem Cause CorrectionProblem Cause Correction Schematic Tractor - Model NumberElectrical Electrical KEY Part DescriptionTractor - Model Number 917,274762 Chassis and Enclosures Tractor - Model Number 917.274762 Chassis and Enclosures KEY Part DescriptionTractor - Model Number 917,274762 Ground Drive Tractor Model Number Part DescriptionTractor - Model Number 917,274762 Steering Assembly Tractor - Model Number 917.274762 Steering Assembly Engine Optional Equipment Spark ArresterTractor - Model Number Seat Assembly 180166Decals Wheels TiresTractor - Model Number 917,274762 Lift Assembly 16 1718Tractor - Model Number 917,274762 Mower Deck 15868 185117 119 113Tractor - Model Number Mower Deck TUVZN c O Hydro Transaxle Model Number20@ 616 1127NIKKIJ All component Dimensions Given in U.S. inches Inch = 25.4 mm Set Only Ride UP and Down Hill Not Across HillDegrees MAX Iiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiii Our Home

917.274762 specifications

The Craftsman 917.274762 is a high-performance lawn tractor designed for residential homeowners who prioritize both efficiency and ease of use in their outdoor maintenance tasks. Equipped with a robust 24 HP Kohler engine, the 917.274762 provides ample power for tackling a variety of yard sizes and terrains, ensuring that grass cutting is both swift and efficient. With its reliable engine, this tractor can handle not just mowing but also light towing and hauling tasks around the yard.

One of the standout features of the Craftsman 917.274762 is its 42-inch cutting deck. This mid-sized deck strikes a perfect balance between maneuverability and cutting capability, making it suitable for both small and medium-sized lawns. The deck is equipped with a cutting height adjustment feature that allows users to choose from a variety of settings for a customizable cut, ensuring a clean and precise lawn finish every time. The deck's design promotes optimal grass collection, resulting in minimal clumping and a healthier lawn overall.

The user-friendly design of the tractor enhances the overall mowing experience. The control panel is intuitively placed, offering easy access to start, stop, and speed control features. Furthermore, the tractor features a comfortable, adjustable seat that provides ergonomic support for longer mowing sessions. For added convenience, the Craftsman 917.274762 boasts a tight turning radius, allowing users to navigate around trees, flowerbeds, and other landscape features with ease.

Safety is also a priority in the Craftsman 917.274762. The tractor comes equipped with an automatic blade brake, ensuring that the blades disengage when the operator leaves the seat, reducing the risk of accidents. Additionally, the sturdy construction and durable materials used in the tractor's design promise longevity and resilience against the wear and tear of regular use.

Overall, the Craftsman 917.274762 combines power, versatility, and comfort, making it an excellent choice for homeowners looking to maintain their lawns with ease. Its reliable engine, impressive cutting capabilities, and user-centric features make it a valuable asset in any outdoor toolkit. Whether you are mowing the lawn or tackling more demanding landscaping tasks, this lawn tractor is designed to meet a variety of needs with efficiency and style.
Top Page Image Contents