Craftsman 917.28922 To Replace Mower Blade Drive Belt, Belt Removal, Belt Installation

Page 24

TO REPLACE MOWER BLADE DRIVE BELT

The mower blade drive belt may be replaced without tools. Park the tractor on level sur-

face. Engage parking brake.

BELT REMOVAL-

1.Remove mowerfrom tractor (See"TO RE- MOVE MOWER"inthissection ofmanua0.

2.Work belt off both mandrel pulleys and idler pulleys.

3.Pull belt away from mower.

BELT INSTALLATION -

. Work belt around both mandrel pulleys and idler pulleys

2.Make sure belt is in all pulley grooves and inside all belt guides.

3.Install mower (See "To Install Mower" in this section of this manual).

MandrelIdler

PullePulle

Mandrel

2.Pull belt toward front of tractor and roll belt onto engine pulley (E).

3.Pull belt toward rear of tractor. Carefully work belt down around transmission

cooling fan and onto the input pulley (D). Be sure belt is inside the belt keeper.

4.Install belt on centerspan idler (C).

5.Install belt through stationary idler (A) and clutching idler (B).

6.Make sure belt is in all pulley grooves and inside all belt guides and keepers.

7.Install mower (See "TO INSTALL MOW- ER" in this section of manual).

03043

TO REPLACE MOTION DRIVE BELT

Park the tractor on level surface. Engage parking brake. For assistance, there is a

belt installation guide decal on bottom side of left footrest.

BELT REMOVAL-

1. Remove mower (See "TO REMOVE MOWER" in this section of manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

2.Remove beltfrom stationary idler (A) and clutching idler (B).

3.Remove belt from centerspan idler (C).

6.Pull belt slack toward rear of tractor.

Carefully remove belt upwards from

transmission input pulley and over cool-

ing fan blades (D).

4. Remove belt downward from engine pulley (E).

5.Slide belt toward rear of tractor, off the steering plate (F) and remove from tractor.

BELT INSTALLATION -

1.Install new belt from tractor rear to front, over the steering plate (F) and above

TO CHECK BRAKE

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced.

You may also check brake by:

1.Park tractor on a level, dry concrete or paved surface, depress brake pedal all the way down and engage parking brake.

2.Disengage transmission by placing

freewheel control in "transmission dis-

engaged" position. Pull freewheel control out and into the slot and release so it is

held in the disengaged position.

The rear wheels must lock and skid when you try to manually push the tractor forward. If the rear wheels rotate, then the brake needs to be serviced. Contact a Sears or other qualified service center.

FRONT WHEEL TOE-IN/CAMBER

Your new tractor front wheel toe-in and cam- ber is set at the factory and is normal. The front wheel toe-in and cam ber are not adjust- able. If damage has occurred to affect the factory set front wheel toe-in or camber, con- tact a Sears or other qualified service center.

clutch brake pedal shaft (G).

24

 

Page 23 Page 25
Image 24
Page 23 Page 25
Contents LAW Tracto SEARS, Roebuckand CO., Hoffman ESTATES, IL 60179 U.S.ACraftsman Full Warranty TWO Years on Riding EquipmentGeneral Operation Service Safe Handling of GasolineGeneral Service Product Specifications Repair ProtectionTools Required for Assembly To Adjust SeatCheck Battery To Remove Tractor from CartonCheck Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake System@@@ Know Your Tractor Reverse Operation SystemHOW to USE Your Tractor To SET Parking BrakeStopping To Adjust Mower Cutting Height To Adjust Gauge WheelsTo Move Forward Backward To Operate MowerTo Transport Transmission Engaged Transmission DisengagedReverse Operation System ROS Before Starting the Engine To Start EngineAutomatic Transmission Warm UP Check Engine OIL LevelPurge Transmission Mowing TiPSLubrication Chart MaintenanceGeneral Recommendations Before Each USETractor Brake OperationTires Operator Presence System and Reverse Operation System ROSTransaxle Pump Fluid EngineAIR Filter Engine Cooling SystemMuffler Spark PlugsImportant Tug hose ensuring connec- tion is secure Deck Washout PortTo Install Mower To Remove Mower03042tex Visual SIDE-TO-SIDE Adjustment FRONT-TO-BACK AdjustmentPrecision SIDE-TO-SIDE Adjustment To Level MowerBelt Installation To Replace Mower Blade Drive BeltBelt Removal To Replace Motion Drive BeltTo Remove Wheel for Repairs To Remove Hood & Grill Assembly To Adjust Choke ControlTo Replace Headlight Bulb Interlocks and RelaysFuel System Engine OILCylinders Problem Cause CorrectionProblemcause Loss of powerProblem Level mower deckLoss OFFSuggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXEspecifJcaciones del Producto Lesiones graves o la muerte Funcionamiento GeneralIII. Niios IV. RemolqueManipulacion Segura DE LA Gasolina Operaciones DE Servicio GeneralesPage Especificaciones DEL Producto Responsabilidades DEL ClienteAcuerdos DE Proteccion Para LA ReparacionHerramientas Necesarias Para EL Montaje Para Remover EL Tractor DELA Caja DE Carton Desempaque LA Caja DE Carton Verifique LA BateriaRevision DE LA Presion DE LAS Llantas Revjsion DE LA Nivelacion DEL ConjuntoRevision DEL Sistema DE Frenos Jlista DE Revision@@@ Familiaricese CON SU Tractor SU TractorIstema DE Funcionamiento Hacia Como Usar SU Tractor MientoParada LA Segadora Usar EL Sistema DE Funcionamiento ATR,S Para Operar EN CerrosPara Transportar Transmision Enganchada Transmision DesenganchadaAgreguegasolina Purgar LA Transmision Consejos Para SegarTabla DE Lubricacion Recomendaciones GeneralesAntes DE Cada USO Tractor LlantasVI= Rifiez Sistema Func Ionam Iento AT R/,S ROS Cuidado DE LA CuchillaMotor TransejeCorreas Para Cambiar EL Aceite DEL MotorLimpieza Manguera Puerto de Lavado Adaptador de Boq DE Cesped Para Desmontar LA CortadoraInstale LA Segadora 03042tex Para Nivelar LA Segadora Regulacion Visual DE Lado a LadoRegulacion DE LA Precision DE Lado Ajuste DE Delante a ATR,SParacambiarla Correa DE Impulsion DE LA Cuchilla Segadora Remocion DE LA CorreaInstalacion DE LA Correa Montaje DE LA CorreaMEC.&NICO Para ADJ Untar LOS CAB LES D E EM Palm EReemplazar LA Bateria Para Cambiar EL FusiblePara Remover EL Conjunto DEL Capo Y DEL Enrejado Para Cambiar LA Bombilla DE LA LUZ DelanteraOtros Sistema DE CombustibleAceite DEL Motor CilindrosProblema Causa Correccion IDENTIFICACI6N DE ProblemasEstrangulacion Choke Identificacion DE Problemas ProblemacausaCorreccion Las cuchillas Page Operacion Segura Cuesta Abajo Y no Atraviese EL Cerro15GRADOS MAX Needmorehelp
Top Page Image Contents