To Level Mower Housing

5.Connect suspension arms to rear deck brackets and secure with retainer

springs.

6.Connect anti-sway bar to chassis bracket and secure with retainer spring.

7.Install belt into electric clutch pulley groove.

Adjust the mower while tractor is parked on level ground or driveway. Make sure

tires are properly inflated (See "PROD-

UCT SPECIFICATIONS" section of this

manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT WITH BUBBLE LEVEL

NOTE: If necessary, check side-to-side surface below tractor for levelness with a

long board and the bubble level.

•Using the lift lever, place mower in posi- tion where no part of the mower, includ- ing gauge wheels, is touching the ground.

•From left side of tractor, find the level

decal on top of mower and place bubble level on decal as indicated.

•Mower is level side-to-side when bubble is between the two lines in the bubble level.

•If adjustment is necessary, under left hand footrest, turn lift link adjustment nut (above yellow cap) in appropriate direction to bring bubble between the lines in the bubble level.

•Remove bubble level from mower and store in a safe place.

Bubble Between	Bubble	Level
Lines
	Level Decal
Brake//_\	Left Hand
Pedal	/_ootrest
	Lift	Link
		astment
Yellow Cap	Nut
ALTERNATE SIDE-TO-SIDE
ADJUSTMENT	METHOD

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of

mower to ground. Distance "A" on both sides of mower should be the same or within 1/4" of each other.

•If adjustment is necessary, make adjust- ment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Each full turn of adjustment nut will change mower height about 1/8".

•Recheck measurements after ad- justing.

Bottom	Edge of	Bottom Edge of
Mower	to Ground	Mower to Ground

Suspension

Arm

Lift Link

ustment

Nut

FRONT-TO-BACK ADJUSTMENT

IMPORTANT: Deck must be level side-to- side. If the following front-to-back adjust- ment is necessary, be sure to adjust both

front links equally so mower will stay level side-to-side.

To obtain the best cutting results, the mower housing should be adjusted so

that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in

its highest position.

Check adjustment on right side of tractor. Measure distance "D" directly in front of and behind the mandrel at bottom edge of mower housing as shown.

•Before making any necessary adjust- ments, check that both front links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut "E"

on both front links an equal number of turns.

•When distance "D" is 1/8" to 1/2"

lower at front than rear, tighten nuts "F" against trunnion on both front links.

•To raise front of mower, loosen nut "F" from trunnion on both front links. Tighten nut "E" on both front links an equal num- ber of turns. The two front links must remain equal in length.

•When distance "D" is 1/8" to 1/2" lower

at front than rear, tighten nut "F" against trunnion on both front links.

Recheck side-to-side adjustment.

917.273642 specifications

The Craftsman 917.273642 is a riding lawn mower designed to combine efficiency, power, and user comfort for homeowners managing sizable lawn areas. This model stands out as an essential gardening tool, specifically engineered to make mowing tasks simpler and more enjoyable.

One of the main features of the Craftsman 917.273642 is its robust 19.5 HP Briggs & Stratton engine. This powerful engine ensures reliable starting and sufficient power to tackle tough grass and larger terrains. The mower also incorporates a smooth-running automatic transmission, allowing users to shift seamlessly between different speeds while maintaining control and stability.

Another key characteristic of this riding mower is its 42-inch cutting deck. This mid-sized deck provides an optimal balance between cutting efficiency and maneuverability, especially in tight spots or around obstacles. The deck is equipped with a six-position height adjustment system, enabling users to customize the cutting height according to the specific requirements of their lawn.

The Craftsman 917.273642 also features an innovative debris management system with side discharge capability, allowing clippings to be expelled directly to the side, providing a cleaner cut and reducing the need for bagging. For added convenience, the model is equipped with optional mulching capabilities, enabling users to finely chop grass clippings and return them to the lawn as natural fertilizer.

User comfort is paramount in the design of the Craftsman 917.273642. The mower incorporates a spacious and ergonomically designed seat, featuring a high back for enhanced support, ensuring users can operate the machine for extended periods without discomfort. The easy-to-reach controls are strategically located on the dashboard, allowing for a user-friendly experience.

In addition to its impressive features, the Craftsman 917.273642 comes with durability in mind. The heavy-duty steel frame and reinforced deck ensure that the mower can withstand the rigors of frequent use while providing a long life span.

Overall, the Craftsman 917.273642 is more than just a lawn mower. It represents a blend of modern technology, user-centric design, and the durability that the Craftsman brand is well known for, making it a valuable addition to any homeowner's gardening toolkit. Whether you have a small yard or a larger landscape, this riding mower is designed to meet your landscaping needs with precision and ease.