Craftsman 917.273642 To Replace Motion Drive Belt, Transaxle Motion Control, Transmission Removal

Page 25

TO REPLACE MOTION DRIVE BELT

Park the tractor on level surface. Engage parking brake. For assistance, there is a

belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

1.Remove mower (See "TO REMOVE

MOWER" in this section of manual). NOTE: Observe entire motion drive belt

and position of all belt guides and keepers.

2.Disconnect clutch wire harness.

3.Remove clutch Iocator.

4.Remove belt from stationary idler and clutching idler.

5.Remove belt downward from engine pulley and around electric clutch.

6.Pull belt slack toward rear of tractor. Carefully remove belt upwards from

transmission input pulley and over cooling fan blades.

7.Remove belt from center span keeper and pull belt away from tractor.

BELT INSTALLATION -

1.Carefully work new belt down around

transmission cooling fan and onto the input pulley.

2.Slide belt into the center span keeper.

3.Pull belt toward front of tractor and roll belt around electric clutch and onto engine pulley.

4.Install belt through stationary idler and clutching idler.

5.Reinstall clutch Iocator and tighten nut securely.

6.Reconnect clutch harness.

7.Make sure belt is in all pulley grooves and inside all belt guides and keepers.

8.Install mower (See "TO INSTALL MOWER" in this section of manual).

Electric --._..

Clutch

 

 

Clutch

_j_,"

"Locator

Clutching--

__'_i_

 

Idler

\_ I

I

Stationary_

_::_l [

Idler

_ _/-[

\

Center Span

 

Keeper

r

Clutch

 

 

Wire

Transmission

_

 

Input Pulley

_

@ Harness

 

TRANSAXLE MOTION CONTROL

LEVER NEUTRAL ADJUSTMENT

The motion control lever has been preset at the factory and adjustment should not be necessary.

1.Loosen adjustment bolt in front of the right rear wheel, and lightly tighten.

2.Start engine and move motion con- trol lever until tractor does not move

forward or backward.

3.Hold motion control lever in that posi- tion and turn engine off.

4.While holding motion control lever in place, loosen the adjustment bolt.

5.Move motion control lever to the neu- tral (N) (lock gate) position.

6.Tighten adjustment bolt securely. NOTE: If additional clearance is needed

to get to adjustment bolt, move mower deck height to the lowest position.

After above adjustment is made, if the

tractor still creeps forward or backward while motion control lever is in neutral

position, follow these steps:

1.Loosen the adjustment bolt.

2.Move the motion control lever 1/4 to 1/2 inch in the direction it is trying to creep.

3.Tighten adjustment bolt securely.

4.Start engine and test.

5.If tractor still creeps, repeat above steps until satisfied.

Motion Control Lever

Neutral

Lock Gate

 

.....

Adjustment Bolt

TRANSMISSION REMOVAL/

REPLACEMENT

Should your transmission require removal for service or replacement, it should be purged

after reinstallation and before operating the

tractor. See "PURGE TRANSMISSION" in the Operation section of this manual.

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Criiftsmhn Limitedwarrantyon Craftsmanridingequipment General Operation III. Children Service Safe Handling of GasolineII. Slope Operation General Service Customer Responsibilities Sears Installation ServiceRepair Protection Agreements For Future Use Adjust Seat HOW to SET UP Your Tractor Check BatteryTo Drive Tractor OFF Skid Unpack CartonDischarging Reposition Right Rear Gauge WheelCheck for Proper Position ALL Belts Check Brake SystemChecklist @@@@ Tractor To SET Parking Brake To Adjust Mower Cutting HeightStopping To USE Throttle ControlTo Operate Mower To Adjust Gauge WheelsTo Operate on Hills To TransportBefore Starting the Engine Check Engine OIL Level Towing Carts and Other Attach MentsADD Gasoline Purge Transmission Automatic Transmission Warm UPMowing Tips Mulching Mowing TipsGeneral Recommendations Maintenance ScheduleTractor BatteryOperator Presence System Blade CareEngine Lubrication Transaxle Pump FluidAIR Filter Engine OIL FilterEngine Cooling System MufflerDisengaged To Install MowerTo Remove Mower SIDE-TO-SIDE Adjustment with Bubble Level To Level Mower HousingFRONT-TO-BACK Adjustment Both Front Links Must be Equal Length To Check and Adjust BrakeTo Replace Mower Blade Drive Belt Replacement Lever Neutral AdjustmentTo Replace Motion Drive Belt Transaxle Motion ControlReplacing Battery To Adjust Steering Wheel AlignmentTo Remove Wheel for Repairs To Replace Headlight Bulb To Adjust Throttle Control CableInterlocks and Relays To Replace FusePreliminary Setting To Adjust CarburetorFinal Setting Acceleration TestEngine OIL Engine Fuel SystemCylinders OtherCause Correction ProblemStart Cause Loss of powerCorrection ProblemcauseTractor - Model Number SchematicElectrical Part Description Electrical KEYTractor - Model Number 917,273642 Chassis and Enclosures Part Description Tractor - Model Number Ground Drive KEY Part Description Tractor -- Model Number Ground DriveTractor - Model Number 917.273642 Steering Assembly KEY Part Description Engine Tractor - Model Number 917,273642KEY Part Tractor - Model Number Seat AssemblyWheels Tires KEY DecalsTractor - Model Number 917,273642 Lift Assembly Tractor - Model Number 917,273642 Mower Deck 144 ,.....4sSTD Tractor - Model Number Mower DeckPage 750x.625 Tractor - Model Number Hydro Geartransaxle -- Model Number783J Briggs ENGINE-MODEL Number 31P777, Type Number 0348-E1 Tractor Model Number105137 276 Dimensions Given in U.S. inches Page Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationYour Home

917.273642 specifications

The Craftsman 917.273642 is a riding lawn mower designed to combine efficiency, power, and user comfort for homeowners managing sizable lawn areas. This model stands out as an essential gardening tool, specifically engineered to make mowing tasks simpler and more enjoyable.

One of the main features of the Craftsman 917.273642 is its robust 19.5 HP Briggs & Stratton engine. This powerful engine ensures reliable starting and sufficient power to tackle tough grass and larger terrains. The mower also incorporates a smooth-running automatic transmission, allowing users to shift seamlessly between different speeds while maintaining control and stability.

Another key characteristic of this riding mower is its 42-inch cutting deck. This mid-sized deck provides an optimal balance between cutting efficiency and maneuverability, especially in tight spots or around obstacles. The deck is equipped with a six-position height adjustment system, enabling users to customize the cutting height according to the specific requirements of their lawn.

The Craftsman 917.273642 also features an innovative debris management system with side discharge capability, allowing clippings to be expelled directly to the side, providing a cleaner cut and reducing the need for bagging. For added convenience, the model is equipped with optional mulching capabilities, enabling users to finely chop grass clippings and return them to the lawn as natural fertilizer.

User comfort is paramount in the design of the Craftsman 917.273642. The mower incorporates a spacious and ergonomically designed seat, featuring a high back for enhanced support, ensuring users can operate the machine for extended periods without discomfort. The easy-to-reach controls are strategically located on the dashboard, allowing for a user-friendly experience.

In addition to its impressive features, the Craftsman 917.273642 comes with durability in mind. The heavy-duty steel frame and reinforced deck ensure that the mower can withstand the rigors of frequent use while providing a long life span.

Overall, the Craftsman 917.273642 is more than just a lawn mower. It represents a blend of modern technology, user-centric design, and the durability that the Craftsman brand is well known for, making it a valuable addition to any homeowner's gardening toolkit. Whether you have a small yard or a larger landscape, this riding mower is designed to meet your landscaping needs with precision and ease.
Top Page Image Contents