Craftsman 917.273642 manual Tractor, Operator Presence System, Blade Care, Blade Removal, Battery

Page 19

TRACTOR

Always observe safety rules when per- forming any maintenance.

BRAKE OPERATION

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted. (See "TO ADJUST BRAKE" in the Service and Adjustments section of this manual).

TIRES

Maintain proper air pressure in all tires (See "PRODUCT SPECIFICATIONS" section of this manual).

Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.

Avoid stumps, stones, deep ruts, sharp

objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts

dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM

Be sure operator presence and interlock systems are working properly. If your trac- tor does not function as described, repair the problem immediately.

The engine should not start unless

the brake pedal is fully depressed and attachement clutch control is in the

disengaged position.

When the engine is running, any at- tempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

When the engine is running and the attachment clutch is engaged, any at- tempt by the operator to leave the seat should shut off the engine.

The attachment clutch should never op-

erate unless the operator is in the seat.

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

BLADE REMOVAL

1.Raise mower to highest position to al- low access to blades.

2.Remove blade bolt, lock washer and flat washer securing blade.

3.Install new or resharpened blade with

trailing edge up towards deck as shown. IMPORTANT: To ensure proper assembly, center hole in blade must align with star on mandrel assembly.

4.Reassemble blade bolt, lock washer and flat washer in exact order as shown.

5.Tighten blade bolt securely (27-35 Ft. Lbs. torque).

IMPORTANT: Blade bolt is heat treated.

If bolt needs replacing, replace only with approve bolt shown in the Repair Parts.

Trailing

Blade Center

Edge Up

Hole

 

Mandrel

 

Assembly

Lock Washer

j/

_- Blade Bolt

TO SHARPEN BLADE

NOTE: We do not recommend sharp-

ening blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An unbalanced blade will cause

excessive vibration and eventual damage to mower and engine.

The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower.

To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with balancer.)

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

Blade

5/8" Bolt or Pin

Center Hole

BATTERY

Your tractor has a battery charging system which is sufficient for normal use. How-

ever, periodic charging of the battery with an automotive charger will extend its life.

Keep battery and terminals clean.

Keep battery bolts tight.

Keep small vent holes open.

Recharge at 6-10 amperes for 1 hour. NOTE: The original equipment battery on

your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.

19

Image 19
Contents Criiftsmhn Limitedwarrantyon Craftsmanridingequipment General Operation III. Children Service Safe Handling of GasolineII. Slope Operation General Service Customer Responsibilities Sears Installation ServiceRepair Protection Agreements For Future Use Unpack Carton HOW to SET UP Your Tractor Check BatteryAdjust Seat To Drive Tractor OFF SkidCheck Brake System Reposition Right Rear Gauge WheelDischarging Check for Proper Position ALL BeltsChecklist @@@@ Tractor To USE Throttle Control To Adjust Mower Cutting HeightTo SET Parking Brake StoppingTo Transport To Adjust Gauge WheelsTo Operate Mower To Operate on HillsBefore Starting the Engine Check Engine OIL Level Towing Carts and Other Attach MentsADD Gasoline Purge Transmission Automatic Transmission Warm UPMowing Tips Mulching Mowing TipsGeneral Recommendations Maintenance ScheduleBlade Care BatteryTractor Operator Presence SystemEngine Lubrication Transaxle Pump FluidMuffler Engine OIL FilterAIR Filter Engine Cooling SystemDisengaged To Install MowerTo Remove Mower SIDE-TO-SIDE Adjustment with Bubble Level To Level Mower HousingFRONT-TO-BACK Adjustment Both Front Links Must be Equal Length To Check and Adjust BrakeTo Replace Mower Blade Drive Belt Transaxle Motion Control Lever Neutral AdjustmentReplacement To Replace Motion Drive BeltReplacing Battery To Adjust Steering Wheel AlignmentTo Remove Wheel for Repairs To Replace Fuse To Adjust Throttle Control CableTo Replace Headlight Bulb Interlocks and RelaysAcceleration Test To Adjust CarburetorPreliminary Setting Final SettingOther Engine Fuel SystemEngine OIL CylindersCause Correction ProblemStart Cause Loss of powerCorrection ProblemcauseTractor - Model Number SchematicElectrical Part Description Electrical KEYTractor - Model Number 917,273642 Chassis and Enclosures Part Description Tractor - Model Number Ground Drive KEY Part Description Tractor -- Model Number Ground DriveTractor - Model Number 917.273642 Steering Assembly KEY Part Description Engine Tractor - Model Number 917,273642KEY Part Tractor - Model Number Seat AssemblyWheels Tires KEY DecalsTractor - Model Number 917,273642 Lift Assembly Tractor - Model Number 917,273642 Mower Deck 144 ,.....4sSTD Tractor - Model Number Mower DeckPage 750x.625 Tractor - Model Number Hydro Geartransaxle -- Model Number783J Briggs ENGINE-MODEL Number 31P777, Type Number 0348-E1 Tractor Model Number105137 276 Dimensions Given in U.S. inches Page Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationYour Home

917.273642 specifications

The Craftsman 917.273642 is a riding lawn mower designed to combine efficiency, power, and user comfort for homeowners managing sizable lawn areas. This model stands out as an essential gardening tool, specifically engineered to make mowing tasks simpler and more enjoyable.

One of the main features of the Craftsman 917.273642 is its robust 19.5 HP Briggs & Stratton engine. This powerful engine ensures reliable starting and sufficient power to tackle tough grass and larger terrains. The mower also incorporates a smooth-running automatic transmission, allowing users to shift seamlessly between different speeds while maintaining control and stability.

Another key characteristic of this riding mower is its 42-inch cutting deck. This mid-sized deck provides an optimal balance between cutting efficiency and maneuverability, especially in tight spots or around obstacles. The deck is equipped with a six-position height adjustment system, enabling users to customize the cutting height according to the specific requirements of their lawn.

The Craftsman 917.273642 also features an innovative debris management system with side discharge capability, allowing clippings to be expelled directly to the side, providing a cleaner cut and reducing the need for bagging. For added convenience, the model is equipped with optional mulching capabilities, enabling users to finely chop grass clippings and return them to the lawn as natural fertilizer.

User comfort is paramount in the design of the Craftsman 917.273642. The mower incorporates a spacious and ergonomically designed seat, featuring a high back for enhanced support, ensuring users can operate the machine for extended periods without discomfort. The easy-to-reach controls are strategically located on the dashboard, allowing for a user-friendly experience.

In addition to its impressive features, the Craftsman 917.273642 comes with durability in mind. The heavy-duty steel frame and reinforced deck ensure that the mower can withstand the rigors of frequent use while providing a long life span.

Overall, the Craftsman 917.273642 is more than just a lawn mower. It represents a blend of modern technology, user-centric design, and the durability that the Craftsman brand is well known for, making it a valuable addition to any homeowner's gardening toolkit. Whether you have a small yard or a larger landscape, this riding mower is designed to meet your landscaping needs with precision and ease.