Craftsman 917.273392 manual HOW to SET UP YOU R Tractor, Tools Required for Assembly, Install Seat

Page 8

Your new tractor has been assembled at the factory with the exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness. Review the video cassette before you begin.

TOOLS REQUIRED FOR

ASSEMBLY

A socket wrench set will make assembly

easier. Standard wrench

sizes you need

are

listed below.

 

 

(1)

3/4"wrench

(1)

Pliers

(2)7/16" wrench (1) Utility knife

(1)Tire pressure gauge

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM

CARTON

UNPACK CARTON

1.Remove all accessible loose parts and parts boxes from carton.

2.Cut along dotted lines on all four pan- els of carton. Remove end panels and lay side panels flat.

3.Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL

ASSEMBLE EXTENSION SHAFT AND BOOT

1.Slide extension shaft onto lower steer-

ing shaft. Align mounting holes in ex- tension and lower shafts and install 1/4

hex bolt and Iocknut. Tighten securely. IMPORTANT: Tighten bolt and nut se- curely to 10-12 ft. Ibs torque.

2.Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

3.Position front wheels of the tractor so they are pointing straight forward.

4.Remove steering wheel adapter from

steering wheel and slide adapter onto steering shaft extension.

5.Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

6.Assemble large flat washer, 1/2 hex nut and tighten securely.

_lnsert

1/2 Hex Nut

Large Flat

Shaft

1/4 Locknut

Slots

7.Snap steering wheel insert into center of steering wheel.

8.Remove protective materials from trac- tor hood and grill.

IMPORTANT: Check for and remove any

staples in skid that may puncture tires where tractor is to roll off skid.

HOW TO SET UP YOU R TRACTOR

INSTALL SEAT

Adjust seat before tightening adjustment knob.

1.Remove adjustment knob and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

2.Pivot seat upward and remove from the cardboard packing. Remove the cardboard packing and discard.

3.Place seat on seat pan so head of shoulder bolts are positioned over the large slotted holes in pan.

4.Push down on seat to engage shoulder

bolts in slots and pull seat towards rear of tractor.

8

Image 8
Contents Jcriiftsmiinj Limited Warranty on Craftsman Riding Equipment Limited Warranty on BatteryGeneral Operation II. Slope OperationIV. Service Do notPage Product Specifications Sears Installation ServiceU1R Customer ResponsibilitiesKeys Steering WheelSeat HOW to SET UP YOU R Tractor Tools Required for AssemblyInstall Seat To Remove Tractor fromCheck Battery Check Deck Levelness @@@@@ Know Your Tractor Attachment Clutch Lever UsedHOW to USE Your Tractor To SET Parking BrakeTo USE Throttle Control Always operate engine at full throttleTo Operate On Hills To TransportTowing Carts and Other Attach Ments Before Starting the EngineTo Start Engine ADD GasolineMowing Tips Mulching Mowing TipsBefore Each USE Lubrication ChartGeneral Recommendations Tractor Blade RemovalBattery EngineTransaxle Cooling BeltsClean AIR Screen AIR FilterEngine OIL Filter Engine Cooling SystemCleaning To Install MowerTractor To Remove MowerTo Level Mower Housing SIDE-TO-SIDE AdjustmentBelt Installation To Check and Adjust BrakeBelt Removal To Check BrakeTransaxle Gear Shift Lever NEU- Tral Adjustment Front Wheel TOE-IN/CAMBERTo Start Engine with a Weak BAT- Tery To Attach Jumper CablesReplacing Battery Interlocks and RelaysTo Replace Fuse To Remove Hood and Grill AS- SemblyTo Adjust Throttle Control Cable To Adjust CarburetorPreliminary Setting Final SettingBattery Remove mower from tractor for winterFuel System Engine OILHard to start Engine will not turn over Troubleshooting ChartIgnition switch Problem Cause Correction Loss of powerExcessive VibrationHeadlights not Working If so equipped CorrectionDischarge Tractor - Model Number Schematic 0LAoKTractor - Model Number ElectricalTractor - Model Number Electrical KEY Part DescriptionTractor - Model Number Chassis and Enclosures Tractor - Model Number Chassis and Enclosures Tractor - Model Number Ground Drive 875 Inches 1 inch = 25.4 mm Tractor - Model Number 917.273392 Steering Assembly Tractor - Model Number 917.273392 Steeringassembly Engine Tractor - Model Number 917.273392 Seat Assembly KEY PartTractor - Model Number Decals RH StltTractor - Model Number Lift Assembly Tractor - Model Number Mower Deck KEY Part Description Numbers Here Part Description 515 O25 4-d O47 % Tractor Model Number 917.273392309 693551 Motor-Starter 868 690968 Page Page Suggested Guide for Sighting Slopes for Safe Operation Get it fixed, at your home or ours

917.273392 specifications

The Craftsman 917.273392 is a robust and versatile lawn mower designed to meet the needs of homeowners who value efficiency, performance, and convenience. This model combines power and user-friendly features to ensure an optimal mowing experience.

One of the standout features of the Craftsman 917.273392 is its powerful engine. Equipped with a reliable Briggs & Stratton engine, it delivers exceptional cutting performance, making it ideal for various lawn types and sizes. The engine’s overhead valve design enhances fuel efficiency and provides better torque.

The cutting deck is another impressive aspect of this lawn mower. It features a wide 42-inch cutting deck that allows for quicker mowing of large areas. The deck is equipped with a dual-blade system, which guarantees a clean and precise cut. Additionally, the adjustable cutting height gives users the flexibility to choose their preferred grass length, accommodating different lawn care preferences.

In terms of convenience, the Craftsman 917.273392 does not disappoint. The mower includes a hydrostatic transmission, which provides seamless shifting without the need for a clutch. This feature ensures a smooth operation, allowing the user to focus on mowing rather than managing gears. The ergonomic design of the control panel enhances user comfort, with easy-to-reach levers for controlling speed and cutting height.

Safety is also a priority in the Craftsman 917.273392 design. The mower is equipped with a safety switch that automatically shuts off the engine when the operator leaves the seat, preventing accidents and enhancing peace of mind during operation.

Another valuable characteristic of this mower is its mulching capability. The optional mulching kit enables users to finely chop grass clippings, returning nutrients back to the soil, which can improve lawn health over time. The rear bagger option adds further versatility, allowing for efficient collection and disposal of grass clippings.

Maintenance has been made simpler with the inclusion of easy-access features. The mower deck can be easily cleaned without having to reach underneath, and regular maintenance tasks such as oil changes are straightforward.

Overall, the Craftsman 917.273392 combines power, versatility, and user-centric design elements, making it a reliable choice for homeowners looking to maintain a well-manicured lawn with ease.