Craftsman 917.273392 Belt Removal, Belt Installation, To Check and Adjust Brake, To Check Brake

Page 23

TO REPLACE MOWER BLADE DRIVE

BELT

The mower blade drive belt may be re- placed without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

1.Remove mower from tractor (See "TO REMOVE MOWER" in this section of

manual).

2.Work belt off both mandrel pulleys and idler pulleys.

3.Pull belt away from mower.

BELT INSTALLATION -

1.Work belt around both mandrel pulleys and idler pulleys

2.Make sure belt is in all pulley grooves and inside all belt guides.

3.Install mower (See "To Install Mower" in this section of this manual).

Mandrel

Idler Pulleys

\\

Mandrel

Pulley

TO CHECK AND ADJUST BRAKE

Your tractor is equipped with an adjustable brake system which is mounted on the right side of the transaxle.

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted.

TO CHECK BRAKE

1.Park tractor on a level, dry concrete or

paved surface, depress clutch/brake pedal all the way down and engage parking brake.

2.Place gear shift lever in neutral (N) position.

The rear wheels must lock and skid when

you try to manually push the tractor for- ward. If the rear wheels rotate, the brake

needs to be adjusted or the pads need to be replaced.

TO ADJUST BRAKE

1.Depress clutch/brake pedal all the way down and engage parking brake.

2.Measure distance between brake oper- ating arm and nut "A" on brake rod.

3.If distance is other than 1-1/2", loosen jam nut and turn nut "A" until distance becomes 1-1/2". Retighten jam nut against nut "A".

4.Road test tractor for proper stopping distance as stated above. Readjust if necessary. If stopping distance is still greater than five (5) feet in highest gear, further maintenance is neces-

sary. Replace brake pads or contact a Sears or other qualified service center.

With Parking Brake "Engaged"

Arm

TO REPLACE MOTION DRIVE BELT

Park the tractor on level surface. Engage parking brake. For assistance, there is a

belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

1. Remove mower (See "TO REMOVE

MOWER" in this section of manual). NOTE: Observe entire motion drive belt

and position of all belt guides and keepers.

2.Remove belt from stationary idler and clutching idler.

3.Remove belt downward from around engine pulley.

4.Pull belt slack toward rear of tractor. Remove belt upwards from transaxle pulley by deflecting belt keepers.

5.Remove belt from center span keeper and pull belt away from tractor.

BELT INSTALLATION -

1.Carefully work new belt down between transaxle belt keepers and onto the input pulley.

2.Slide belt into the center span keeper.

3.Pull belt toward front of tractor and roll around the top groove of engine pulley.

4.Install belt through stationary idler and clutching idler.

23

Image 23
Contents Jcriiftsmiinj Limited Warranty on Battery Limited Warranty on Craftsman Riding EquipmentII. Slope Operation General OperationDo not IV. ServicePage Customer Responsibilities Product SpecificationsSears Installation Service U1RKeys Steering WheelSeat To Remove Tractor from HOW to SET UP YOU R TractorTools Required for Assembly Install SeatCheck Battery Check Deck Levelness @@@@@ Attachment Clutch Lever Used Know Your TractorAlways operate engine at full throttle HOW to USE Your TractorTo SET Parking Brake To USE Throttle ControlBefore Starting the Engine To Operate On HillsTo Transport Towing Carts and Other Attach MentsADD Gasoline To Start EngineMulching Mowing Tips Mowing TipsBefore Each USE Lubrication ChartGeneral Recommendations Blade Removal TractorBelts BatteryEngine Transaxle CoolingEngine Cooling System Clean AIR ScreenAIR Filter Engine OIL FilterTo Remove Mower CleaningTo Install Mower TractorSIDE-TO-SIDE Adjustment To Level Mower HousingTo Check Brake Belt InstallationTo Check and Adjust Brake Belt RemovalTo Attach Jumper Cables Transaxle Gear Shift Lever NEU- Tral AdjustmentFront Wheel TOE-IN/CAMBER To Start Engine with a Weak BAT- TeryTo Remove Hood and Grill AS- Sembly Replacing BatteryInterlocks and Relays To Replace FuseFinal Setting To Adjust Throttle Control CableTo Adjust Carburetor Preliminary SettingEngine OIL BatteryRemove mower from tractor for winter Fuel SystemHard to start Engine will not turn over Troubleshooting ChartIgnition switch Vibration Problem Cause CorrectionLoss of power ExcessiveHeadlights not Working If so equipped CorrectionDischarge 0LAoK Tractor - Model Number SchematicElectrical Tractor - Model NumberKEY Part Description Tractor - Model Number ElectricalTractor - Model Number Chassis and Enclosures Tractor - Model Number Chassis and Enclosures Tractor - Model Number Ground Drive 875 Inches 1 inch = 25.4 mm Tractor - Model Number 917.273392 Steering Assembly Tractor - Model Number 917.273392 Steeringassembly Engine KEY Part Tractor - Model Number 917.273392 Seat AssemblyRH Stlt Tractor - Model Number DecalsTractor - Model Number Lift Assembly Tractor - Model Number Mower Deck KEY Part Description Numbers Here Part Description 515 O25 4-d O47 % 917.273392 Tractor Model Number309 693551 Motor-Starter 868 690968 Page Page Suggested Guide for Sighting Slopes for Safe Operation Get it fixed, at your home or ours

917.273392 specifications

The Craftsman 917.273392 is a robust and versatile lawn mower designed to meet the needs of homeowners who value efficiency, performance, and convenience. This model combines power and user-friendly features to ensure an optimal mowing experience.

One of the standout features of the Craftsman 917.273392 is its powerful engine. Equipped with a reliable Briggs & Stratton engine, it delivers exceptional cutting performance, making it ideal for various lawn types and sizes. The engine’s overhead valve design enhances fuel efficiency and provides better torque.

The cutting deck is another impressive aspect of this lawn mower. It features a wide 42-inch cutting deck that allows for quicker mowing of large areas. The deck is equipped with a dual-blade system, which guarantees a clean and precise cut. Additionally, the adjustable cutting height gives users the flexibility to choose their preferred grass length, accommodating different lawn care preferences.

In terms of convenience, the Craftsman 917.273392 does not disappoint. The mower includes a hydrostatic transmission, which provides seamless shifting without the need for a clutch. This feature ensures a smooth operation, allowing the user to focus on mowing rather than managing gears. The ergonomic design of the control panel enhances user comfort, with easy-to-reach levers for controlling speed and cutting height.

Safety is also a priority in the Craftsman 917.273392 design. The mower is equipped with a safety switch that automatically shuts off the engine when the operator leaves the seat, preventing accidents and enhancing peace of mind during operation.

Another valuable characteristic of this mower is its mulching capability. The optional mulching kit enables users to finely chop grass clippings, returning nutrients back to the soil, which can improve lawn health over time. The rear bagger option adds further versatility, allowing for efficient collection and disposal of grass clippings.

Maintenance has been made simpler with the inclusion of easy-access features. The mower deck can be easily cleaned without having to reach underneath, and regular maintenance tasks such as oil changes are straightforward.

Overall, the Craftsman 917.273392 combines power, versatility, and user-centric design elements, making it a reliable choice for homeowners looking to maintain a well-manicured lawn with ease.