Toremovehood and Grill AS Sembly | Craftsman 917.272068 specification

Craftsman 917.272068 Toremovehood and Grill AS Sembly, To Adjust THROnLE Control Cable

TOREMOVEHOOD AND GRILL AS-

SEMBLY

1.Raise hood.

2.Unsnap headlight wire connector.

3.Stand in front of tractor. Grasp hood at

sides, tilt toward engine and lift off of tractor.

4.When replacing hood, be sure to reconnect the headlight wire connec- tor.

Headlight Wire

Connector

ENGINE

Maintenance, repair, or replacement of the emission control devices and systems, which are being done at the customers expense, may be performed by any non-road engine repair establishment or individual. Warranty repairs must be performed by an authorized engine manufacturer's service outlet.

TO ADJUST THRO'n'LE CONTROL CABLE

The throttle control has been preset at the factory and adjustment should not be necessary. Check adjustment as described below before loosening cable. If adjustment is necessary, proceed as follows:

1.With engine not running, move throttle control lever from slow to choke position. Slowly move lever from choke to fast position.

2.Check to see if hole in throttle lever and hole in speed control bracket are aligned.

3.If holes are not aligned, loosen cable clamp screw and align the holes by

inserting a pencil or a 1/4" drill bit through beth holes.

4.Pull throttle cable up to remove slack and tighten cable clamp screw. Remove alignment pencil or drill bit.

TO ADJUST CARBURETOR

The carburetor has been preset at the factory and adjustment should not be necessary. However, minor adjustment may be required to compensate for differences in fuel, temperature, altitude or load. If the carburetor does need adjustment, proceed as follows: In general, tuming the adjusting needles in (clockwise) decreases the supply of fuel to the engine gMng a leaner fuel/air mixture. Turning the adjusting needles out (counter- clockwise) increases the supply of fuel to the engine giving a richer fuel/air mixture. IMPORTANT: Damage to the needles and seats in carburetor may result if turned in too

tight.

NOTE: The carburetor on this engine is low emission. It is equipped with an idle fuel adjusting needle with a #miter cap, which allows some adjustment within the limits allowed by the cap. Do not attempt to remove the limiter cap. The limiter cap cannot be removed without breaking the adjusting needle.

1.Be sure you have a clean air filter and the throttle control cable is adjusted properly (see above).

2.Start engine and allow to warm for five minutes. Make adjustments with engine running and shift/motion control lever in neutral (N) position.

3.Idle soeed setting - With throttle control lever in slow position, engine should idle at 1750 RPM. If engine idles too slow or

fast, tum idle speed adjusting screw in or out until correct idle is attained.

4.Idle fuel needle setting - With throttle control lever in slow position, rum idle fuel adjustment needle In (clockwise) until engine begins to die and then turn out (counterclockwise) until engine runs rough. Tum needle to a point midway between those two positions.

5.Recheck idle speed. Readjust if neces- sen/.

917.272068 specifications

The Craftsman 917.272068 is a highly efficient and robust lawn tractor designed to meet the needs of both homeowners and professional landscapers. Built with durability and performance in mind, this machine is ideal for tackling a variety of mowing tasks, whether you have a small residential lawn or a more expansive grass area.

One of the standout features of the Craftsman 917.272068 is its powerful 24 HP engine, which provides ample power to handle tough mowing conditions. The engine is specifically designed for reliability and longevity, ensuring that it can provide consistent performance over many seasons. Coupled with the dual blade system, the mower provides an even and clean cut, reducing the need for double mowing and optimizing efficiency.

The 917.272068 is equipped with a 42-inch cutting deck, allowing for wide swath mowing while maintaining agility around obstacles. The cutting height is adjustable, providing users with the flexibility to choose from various settings, ensuring a tailored cut to suit the season or grass type. This versatility makes it particularly advantageous for users with varying mowing preferences and lawn conditions.

Another notable feature is the hydrostatic transmission, which allows for smooth and effortless control of speed and direction. This feature enhances ease of use, particularly for those who may not be accustomed to operating larger machinery. The responsive controls enable precise maneuverability, making it possible to navigate tightly spaced areas with ease.

The Craftsman 917.272068 also includes comfortable seating and a user-friendly dashboard that displays essential information at a glance, such as fuel level and maintenance reminders. This focus on operator comfort is a crucial aspect of its design, making long mowing sessions more enjoyable and less fatiguing.

In terms of technology, the Craftsman 917.272068 supports mulching and rear discharge capabilities, providing users with the option to either recycle grass clippings back onto the lawn for nutrient replenishment or easily discharge clippings behind the mower. This dual functionality enhances the utility of the mower, catering to different user preferences and lawn care practices.

Overall, the Craftsman 917.272068 stands out with its fusion of power, efficiency, and user-friendly features. Its reliable performance, combined with adjustable mowing options and comfortable operation, positions it as a top choice for anyone looking to achieve a well-maintained lawn. Whether for residential use or professional landscaping, this lawn tractor is built to deliver excellent results season after season.