Craftsman 917.27206 Replacing Battery To Remove Hood and Grill AS Sembly, Interlocks and Relays

Page 27

REPLACING BATTERY

TO REMOVE HOOD AND GRILL AS-

 

SEMBLY

_CAUTION: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch

bands, rings, etc.

Positive terminal must be connected first

to prevent sparking from accidental grounding,

1.Lift seat pan to raised position and open battery box door.

2.Disconnect BLACK battery cable first then RED battery cable and carefully remove battery from tractor.

3.Install new battery with terminals in same position as old battery.

4.First connect RED battery cable to positive (+) terminal with hex bolt and keps nut as shown. Tighten securely.

5.Connect BLACK grounding cable to negative (-) terminal with remaining

hex bolt and keps nut. Tighten securely.

6: Close battery box door.

Battery

Box

Positive(Red) Cable Negative (Black) Cable

TO REPLACE HEADLIGHT BULB

1.Raise hood.

2.Pull bulb holder out of the hole in the backside of the gdll.

3.Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

4.Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring

diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type

plug-in fuse. The fuse holder is located behind the dash.

1.Raise hood.

2.Unsnap headlight wire connector.

3.Stand in front of tractor. Grasp hood at

sides, tilt toward engine and lift off of tractor.

4.To replace, reverse above procedure.

/Hood

' HeadlightWire

.... i/' Connector

ENGINE

Maintenance, repair,or replacement of the emission controldevices and systems, which are being done at the customersexpense, may be performed by any non-reed engine repair establishmentor individual.Warranty repairsmust be performed by an authorized engine manufactureCsservice outlet.

TO ADJUST THROTTLE CONTROL CABLE

The throttlecontrol has been preset at the factory end adjustment should not be necessary. Check adjustreent as descnbed

below before loosening cable. If adjustment is necessary,proceed as follows:

1.With engine not funning, move throttle control lever from slow to choke posillon. Slowly move lever from choke to fast position.

2.Check to see if hole in throttle lever end bole in speed control bracket are aligned.

3.If holes are not aligned, loosen cable clamp screw and align the holes by insertinga pencil or a 1/4" ddll bit through both boles.

4.Pull throttle c_ble up to remove slack and tighten cable clamp screw. Remove alignment pencil or drillbit.

Cable _

Clamp -_.____L_

Screw _

Speed Control _'_/_ J

Bracket

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Jcraftsmanj Limited 90 DAY Warranty on Battery Do not General OperationII. Slope Operation III. Children IV. ServiceCancer and birth defects or other repro- ductive harm Product Specifications Repair AgreementCustomer Responsibilities Steedng To Removetractor from Carton Unpack Carton Tools Required for AssemblyAssemble Extension Shaft and Boot Install Steering WheelInstall Seat Checkbrakesystem To Convertto Bagging or DischargingChecktire Pressure Check for Proper Position of ALL Belts@ ixl Engine off Howto Useyourtractor To Transport To Adjust Gauge WheelsTo Operate Mower To Operate on HillsTo Start Engine Towing Carts and Other ATTACH- MentsBefore Startingthe Engine Check Engine OIL Level ADD GasolineAutomatictransmission Warm UP Mulching Mowingtips Before Each USE Lubrication ChartMaintenance Schedule General RecommendationsOperator Presence System TractorBrake Operation TiresEngine Lubrication To Clean Battery and TerminalsProduct Specifications Transaxle Pump FluidClean AIR INTAKE,/COOUNG Areas To Service PRE-CLEANERTo Service Cartridge Clean AIR ScreenIN-LINE Fuel Rlter CleaningTo Remove Mower To Install MowerTo Level Mower Housing TractorBelt Removal To Replace Mower Blade Drive BeltBelt Installation To Adjust BrakeTransaxle Motion Control Lever Neutral Adjustment To REMOVECABLES,REVERSEORDER To AttachjumpercablesInterlocks and Relays Replacing Battery To Remove Hood and Grill AS SemblyTo Adjust Throttle Control Cable To Replace Headlight BulbAccelerationtest To Adjust CarburetorCylinders To Clean Battery and TermiEngine Fuel System Engine OILCause Correction ProblemRoubleshooting Chart ProblemCorrection OFF Troubleshooting Chart ProblemcauseFUESH-OF Tractor - Model Number SchematicTractor - Model Number Electrical KEY Part NO. no Description Tractor --MODEL Number ElectricalTractor -- Model Number 917.272060 Chassis and Enclosures KEY Part Description Tractor - Model Number 917.272060 Chassis and EnclosuresTractor -- Model Number Ground Drive TRACTOR-- MODELNUMBER917.272060 Tractor -- Model Number 917.272060 Steering Assembly KEY Part No NO.DESCRIPTION TRACTOR-- MODELNUMBER917.272060 SteeringassemblyOptional Equipment KEY Part NO. NO.DESCRIPTION Tractor -- Model Number Seat Assembly Wheels &TIRES KEY Part Description NO. no TRACTOR- -MODELNUMBER DecalsTractor -- Model Number Lift Assembly KEY Part NO. NO,DESCRIPTION TRACTOR- Model Number Lift AssemblyTractor -- Model Number Mower Deck TRACTOR-- MODELNUMBER917.272060 Mowerdeck 48107 75xl,750x.625 Cylinder HEAD, Valve and Breather Crankcase KEY Part Descripon Cylinder HEADNALVE/BREATHER KEY Part DescrtionIgnitionielectrical AIR INTAKE/RLTRATION KEY Part Description Blower Housing & Baffles KEY Part NO. NO,DESCRIPTIONIGNITION/ELECTRICAL KEY Part NO. NO,DESCRIPTION Not Illustrated1C2 Starting System KEY Part Description OIL PAN/LUBRICATION KEY Part NO. NO,DESCRIPTIONEngine Controls KEY Part Description Crankshaft ExhaustjFuelsystem Fuel System KEY Part Description Crankshaft KEY Part DescriptionExhaust KEY Part Description Page Only Ride UP and Down Hill Not Across Hill Suggested Guide for Sighting Slopes for Safe OperationPage Page Get it fixed, at your home or ours

917.27206 specifications

The Craftsman 917.27206 is a highly regarded riding lawn mower that has been designed for homeowners seeking an efficient and user-friendly solution for maintaining their lawns. This machine merges power with precision, offering a variety of features that cater to different mowing needs.

One of the standout characteristics of the Craftsman 917.27206 is its robust engine. Equipped with a powerful 19 horsepower Briggs & Stratton engine, this mower ensures reliable performance on a range of terrains. The engine is designed for easy starting and delivers consistent power, making lawn maintenance a breeze even in challenging conditions.

The mower features a 42-inch cutting deck, allowing for an efficient mowing experience. This wide cutting path reduces the time spent mowing, while the deck’s design ensures a clean and even cut. The adjustable cutting height provides versatility, allowing users to select from various settings based on grass height and personal preference. The craftsmanship evident in the deck design also facilitates superior grass dispersal, reducing clumping and enhancing lawn health.

Durability is another defining feature of the Craftsman 917.27206. The heavy-duty steel frame is built to withstand the rigors of regular use, ensuring longevity. The reinforced components alike the front axle and the deck contribute to a sturdy build that is equipped to handle bumps and rough patches throughout your yard.

Designed with user comfort in mind, the mower boasts an ergonomic seat that ensures a comfortable riding experience. The controls are intuitively placed, allowing for easy operation while navigating your lawn. The tight turning radius enhances maneuverability, making it easier to navigate around flower beds and landscaping features.

Another notable technology integrated into the Craftsman 917.27206 is the automatic transmission, which provides seamless speed control. This feature simplifies operation, allowing users to focus on achieving a consistent cut rather than managing gears. The mower also offers rear bagging capabilities, making it easy to collect clippings for disposal or composting.

In summary, the Craftsman 917.27206 is an impressive riding mower characterized by its powerful engine, durable construction, and user-friendly features. Whether you are a seasoned homeowner or new to lawn care, this mower is designed to make maintaining your yard a simpler, more enjoyable task.
Top Page Image Contents