Craftsman 917.27206 owner manual To Replace Mower Blade Drive Belt, Belt Removal

Page 24

SIDE-TO-SIDEADJUSTMENT

Raisemowertoitshighestposition.

At the midpointof bothsides of mower,

measure heightfrom bottomedge of

mowerto ground. Distance"A"on bothsides of mowershouldbe the

same or within 1/4"of each other.

If adjustment is necessary,make adjustmenton one side of moweronly.

To raise one side of mower,tighten lift linkadjustmentnut on that side.

To lowerone side of mower,loosen lift linkadjustmentnut on that side.

NOTE: Each full turn of adjustmentnut willchange mower height about 1/8".

Recheck measurementsafter adjust- ing.

Bottomedge of

_

Bottom edge of

mower to

mower to

ground _

 

ground

n Ann

Lift Link

Adjustment Nut _

--

To raise front of mower, loosen nut "F" from trunnion on both front links.

Tighten nut "E" on both front links an equal number of turns.

When distance "D" is 1/8" to 1/2" lower at front than rear, tighten nut "F" against trunnion on both front links.

Recheck side-to-side adjustment.

-__ndrel

BothFrontLinks Should be Equal in Length

/

Nut ,,_Nut

"E

Trunnion_

FRONT-TO-BACK ADJUSTMENT IMPORTANT: Deck must be level side-to

side. If the following front-to-back adjust-

ment is necessary, be sure to adjust both

front links equally so mower will stay level side-to-side.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in

its highest position.

Check adjustment on right side of tractor. Measure distance "D" directly in front and behind the mandrel at bottom edge of mower housing as shown.

Before making any necessary adjust- ments, check that both front links are equal in length. Both links should be approximately 10-3/8".

If links are not equal in length, adjust one link to same length as other link.

To lower front of mower loosen nut "E"

on both front links an equal number of turns.

When distance "D" is 1/8" to 1/2" lower at front than rear, tighten nuts "F" against trunnion on both front links.

TO REPLACE MOWER BLADE DRIVE BELT

The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

1.Remove mower from tractor (See "TO REMOVE MOWER" in this section of

this manual).

2.Work belt off both mandrel pulleys and idler pulleys.

3.Pull belt away from mower.

Mandrel

Pulle

24

Image 24
Contents Jcraftsmanj Limited 90 DAY Warranty on Battery Do not General OperationII. Slope Operation IV. Service III. ChildrenCancer and birth defects or other repro- ductive harm Product Specifications Repair AgreementCustomer Responsibilities Steedng Tools Required for Assembly Assemble Extension Shaft and BootInstall Steering Wheel To Removetractor from Carton Unpack CartonInstall Seat To Convertto Bagging or Discharging Checktire PressureCheck for Proper Position of ALL Belts Checkbrakesystem@ ixl Engine off Howto Useyourtractor To Adjust Gauge Wheels To Operate MowerTo Operate on Hills To TransportTowing Carts and Other ATTACH- Ments Before Startingthe Engine Check Engine OIL LevelADD Gasoline To Start EngineAutomatictransmission Warm UP Mulching Mowingtips Lubrication Chart Maintenance ScheduleGeneral Recommendations Before Each USETractor Brake OperationTires Operator Presence SystemTo Clean Battery and Terminals Product SpecificationsTransaxle Pump Fluid Engine LubricationTo Service PRE-CLEANER To Service CartridgeClean AIR Screen Clean AIR INTAKE,/COOUNG AreasCleaning IN-LINE Fuel RlterTo Install Mower To Level Mower HousingTractor To Remove MowerTo Replace Mower Blade Drive Belt Belt RemovalBelt Installation To Adjust BrakeTransaxle Motion Control Lever Neutral Adjustment To Attachjumpercables To REMOVECABLES,REVERSEORDERReplacing Battery To Remove Hood and Grill AS Sembly To Adjust Throttle Control CableTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Carburetor AccelerationtestTo Clean Battery and Termi Engine Fuel SystemEngine OIL CylindersProblem Cause CorrectionRoubleshooting Chart ProblemCorrection Troubleshooting Chart Problemcause OFFTractor - Model Number Schematic FUESH-OFTractor - Model Number Electrical Tractor --MODEL Number Electrical KEY Part NO. no DescriptionTractor -- Model Number 917.272060 Chassis and Enclosures Tractor - Model Number 917.272060 Chassis and Enclosures KEY Part DescriptionTractor -- Model Number Ground Drive TRACTOR-- MODELNUMBER917.272060 Tractor -- Model Number 917.272060 Steering Assembly TRACTOR-- MODELNUMBER917.272060 Steeringassembly KEY Part No NO.DESCRIPTIONOptional Equipment KEY Part NO. NO.DESCRIPTION Tractor -- Model Number Seat Assembly TRACTOR- -MODELNUMBER Decals Wheels &TIRES KEY Part Description NO. noTractor -- Model Number Lift Assembly TRACTOR- Model Number Lift Assembly KEY Part NO. NO,DESCRIPTIONTractor -- Model Number Mower Deck TRACTOR-- MODELNUMBER917.272060 Mowerdeck 48107 75xl,750x.625 Cylinder HEAD, Valve and Breather Cylinder HEADNALVE/BREATHER KEY Part Descrtion Crankcase KEY Part DescriponIgnitionielectrical Blower Housing & Baffles KEY Part NO. NO,DESCRIPTION IGNITION/ELECTRICAL KEY Part NO. NO,DESCRIPTIONNot Illustrated AIR INTAKE/RLTRATION KEY Part Description1C2 Starting System KEY Part Description OIL PAN/LUBRICATION KEY Part NO. NO,DESCRIPTIONEngine Controls KEY Part Description Crankshaft ExhaustjFuelsystem Fuel System KEY Part Description Crankshaft KEY Part DescriptionExhaust KEY Part Description Page Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across HillPage Page Get it fixed, at your home or ours

917.27206 specifications

The Craftsman 917.27206 is a highly regarded riding lawn mower that has been designed for homeowners seeking an efficient and user-friendly solution for maintaining their lawns. This machine merges power with precision, offering a variety of features that cater to different mowing needs.

One of the standout characteristics of the Craftsman 917.27206 is its robust engine. Equipped with a powerful 19 horsepower Briggs & Stratton engine, this mower ensures reliable performance on a range of terrains. The engine is designed for easy starting and delivers consistent power, making lawn maintenance a breeze even in challenging conditions.

The mower features a 42-inch cutting deck, allowing for an efficient mowing experience. This wide cutting path reduces the time spent mowing, while the deck’s design ensures a clean and even cut. The adjustable cutting height provides versatility, allowing users to select from various settings based on grass height and personal preference. The craftsmanship evident in the deck design also facilitates superior grass dispersal, reducing clumping and enhancing lawn health.

Durability is another defining feature of the Craftsman 917.27206. The heavy-duty steel frame is built to withstand the rigors of regular use, ensuring longevity. The reinforced components alike the front axle and the deck contribute to a sturdy build that is equipped to handle bumps and rough patches throughout your yard.

Designed with user comfort in mind, the mower boasts an ergonomic seat that ensures a comfortable riding experience. The controls are intuitively placed, allowing for easy operation while navigating your lawn. The tight turning radius enhances maneuverability, making it easier to navigate around flower beds and landscaping features.

Another notable technology integrated into the Craftsman 917.27206 is the automatic transmission, which provides seamless speed control. This feature simplifies operation, allowing users to focus on achieving a consistent cut rather than managing gears. The mower also offers rear bagging capabilities, making it easy to collect clippings for disposal or composting.

In summary, the Craftsman 917.27206 is an impressive riding mower characterized by its powerful engine, durable construction, and user-friendly features. Whether you are a seasoned homeowner or new to lawn care, this mower is designed to make maintaining your yard a simpler, more enjoyable task.