Craftsman 917.27206 Tractor, Brake Operation, Tires, Operator Presence System, Blade Care

Page 19

TRACTOR

Always observe safety rules when

performing any maintenance.

BRAKE OPERATION

If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be ad- justed. (See TO ADJUST BRAKE" in the

Service and Adjustments section of this manual).

TIRES

Maintain proper air pressure in all tires (See "PRODUCT SPECIFICATIONS" section of this manual).

Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.

Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent fiat tires due to slow leaks, tire sealant may be purchased from your local parts

dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM

Be sure operator presence and interlock systems are working properly. If your tractor does not function as described, repair the problem immediately.

The engine should not start unless the

clutch/brake pedal is fully depressed and attachement clutch control is in the

disengaged position.

When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

The attachment clutch should never

operate unless the operator is in the seat.

BLADE CARE

For best results mower blades must be

kept sharp. Replace bent or damaged blades.

BLADE REMOVAL

1.Raise mower to highest position to allow access to blades.

2.Remove hex bolt, lock washer and flat washer securing blade.

3.Install new or resharpened blade with

trailing edge up towards deck as shown.

IMPORTANT: To ensure proper assembly, center hole in blade must align with star on mandrel assembly.

4.Reassemble hex bolt, lock washer and flat washer in exact order as shown.

5.Tighten bolt securely (27-35 Ft. Lbs. torque).

IMPORTANT: Blade bolt is grade 8 heat treated.

TrailingI

Up

Mandrel Assembly

 

Blade

Center

 

 

Hole

Flat Washer

Lock Washer

_€--Hex Bolt

"A Grade 8 heat treated boltcan be identified by six lines on the belt head.

TO SHARPEN BLADE

NOTE: We do not recommend sharpen- ing blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An unbalanced blade will

cause excessive vibration and eventual damage to mower and engine.

The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower.

To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone

balancer. (When using a cone bal- ancer, follow the instructions supplied with balancer.)

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

Slide blade on to an unthraaded

portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

Center Hole

19

Image 19
Contents Jcraftsmanj Limited 90 DAY Warranty on Battery General Operation Do notII. Slope Operation III. Children IV. ServiceCancer and birth defects or other repro- ductive harm Repair Agreement Product SpecificationsCustomer Responsibilities Steedng To Removetractor from Carton Unpack Carton Tools Required for AssemblyAssemble Extension Shaft and Boot Install Steering WheelInstall Seat Checkbrakesystem To Convertto Bagging or DischargingChecktire Pressure Check for Proper Position of ALL Belts@ ixl Engine off Howto Useyourtractor To Transport To Adjust Gauge WheelsTo Operate Mower To Operate on HillsTo Start Engine Towing Carts and Other ATTACH- MentsBefore Startingthe Engine Check Engine OIL Level ADD GasolineAutomatictransmission Warm UP Mulching Mowingtips Before Each USE Lubrication ChartMaintenance Schedule General RecommendationsOperator Presence System TractorBrake Operation TiresEngine Lubrication To Clean Battery and TerminalsProduct Specifications Transaxle Pump FluidClean AIR INTAKE,/COOUNG Areas To Service PRE-CLEANERTo Service Cartridge Clean AIR ScreenIN-LINE Fuel Rlter CleaningTo Remove Mower To Install MowerTo Level Mower Housing TractorBelt Removal To Replace Mower Blade Drive BeltTo Adjust Brake Belt InstallationTransaxle Motion Control Lever Neutral Adjustment To REMOVECABLES,REVERSEORDER To AttachjumpercablesInterlocks and Relays Replacing Battery To Remove Hood and Grill AS SemblyTo Adjust Throttle Control Cable To Replace Headlight BulbAccelerationtest To Adjust CarburetorCylinders To Clean Battery and TermiEngine Fuel System Engine OILCause Correction ProblemProblem Roubleshooting ChartCorrection OFF Troubleshooting Chart ProblemcauseFUESH-OF Tractor - Model Number SchematicTractor - Model Number Electrical KEY Part NO. no Description Tractor --MODEL Number ElectricalTractor -- Model Number 917.272060 Chassis and Enclosures KEY Part Description Tractor - Model Number 917.272060 Chassis and EnclosuresTractor -- Model Number Ground Drive TRACTOR-- MODELNUMBER917.272060 Tractor -- Model Number 917.272060 Steering Assembly KEY Part No NO.DESCRIPTION TRACTOR-- MODELNUMBER917.272060 SteeringassemblyOptional Equipment KEY Part NO. NO.DESCRIPTION Tractor -- Model Number Seat Assembly Wheels &TIRES KEY Part Description NO. no TRACTOR- -MODELNUMBER DecalsTractor -- Model Number Lift Assembly KEY Part NO. NO,DESCRIPTION TRACTOR- Model Number Lift AssemblyTractor -- Model Number Mower Deck TRACTOR-- MODELNUMBER917.272060 Mowerdeck 48107 75xl,750x.625 Cylinder HEAD, Valve and Breather Crankcase KEY Part Descripon Cylinder HEADNALVE/BREATHER KEY Part DescrtionIgnitionielectrical AIR INTAKE/RLTRATION KEY Part Description Blower Housing & Baffles KEY Part NO. NO,DESCRIPTIONIGNITION/ELECTRICAL KEY Part NO. NO,DESCRIPTION Not Illustrated1C2 OIL PAN/LUBRICATION KEY Part NO. NO,DESCRIPTION Starting System KEY Part DescriptionEngine Controls KEY Part Description Exhaustj CrankshaftFuelsystem Crankshaft KEY Part Description Fuel System KEY Part DescriptionExhaust KEY Part Description Page Only Ride UP and Down Hill Not Across Hill Suggested Guide for Sighting Slopes for Safe OperationPage Page Get it fixed, at your home or ours

917.27206 specifications

The Craftsman 917.27206 is a highly regarded riding lawn mower that has been designed for homeowners seeking an efficient and user-friendly solution for maintaining their lawns. This machine merges power with precision, offering a variety of features that cater to different mowing needs.

One of the standout characteristics of the Craftsman 917.27206 is its robust engine. Equipped with a powerful 19 horsepower Briggs & Stratton engine, this mower ensures reliable performance on a range of terrains. The engine is designed for easy starting and delivers consistent power, making lawn maintenance a breeze even in challenging conditions.

The mower features a 42-inch cutting deck, allowing for an efficient mowing experience. This wide cutting path reduces the time spent mowing, while the deck’s design ensures a clean and even cut. The adjustable cutting height provides versatility, allowing users to select from various settings based on grass height and personal preference. The craftsmanship evident in the deck design also facilitates superior grass dispersal, reducing clumping and enhancing lawn health.

Durability is another defining feature of the Craftsman 917.27206. The heavy-duty steel frame is built to withstand the rigors of regular use, ensuring longevity. The reinforced components alike the front axle and the deck contribute to a sturdy build that is equipped to handle bumps and rough patches throughout your yard.

Designed with user comfort in mind, the mower boasts an ergonomic seat that ensures a comfortable riding experience. The controls are intuitively placed, allowing for easy operation while navigating your lawn. The tight turning radius enhances maneuverability, making it easier to navigate around flower beds and landscaping features.

Another notable technology integrated into the Craftsman 917.27206 is the automatic transmission, which provides seamless speed control. This feature simplifies operation, allowing users to focus on achieving a consistent cut rather than managing gears. The mower also offers rear bagging capabilities, making it easy to collect clippings for disposal or composting.

In summary, the Craftsman 917.27206 is an impressive riding mower characterized by its powerful engine, durable construction, and user-friendly features. Whether you are a seasoned homeowner or new to lawn care, this mower is designed to make maintaining your yard a simpler, more enjoyable task.