Craftsman 917.271142 To Level Mower Housing, To Replace Mower Blade Drive Belt, Belt Removal

Page 22

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure

tires are properly inflated (See "PROD-

UCT SPECIFICATIONS" section of this manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance "A" on both sides of mower should be the same or within 1/4" of each other.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE:Each full turn of adjustment nut will change mower height about 1/8".

•Recheck measurements after adjusting.

Bottom edge of

Bottom edge of

mower to groun_ower

to ground

•To lower front of mower loosen nut "E"

on both front links an equal number of turns.

•When distance "D" is 1/8" to 1/2" lower at front than rear, tighten nuts "F" against trunnion on both front links.

•To raise front of mower, loosen nut "F" from trunnion on both front links. Tighten nut "E" on both front links an equal number of turns.

•When distance "D" is 1/8" to 1/2" lower

at front than rear, tighten nut "F" against trunnion on both front links.

•Recheck side-to-side adjustment.

Mandrel

"D"

Both Front Links Should be Equal in Length

rm

Lift Link AI_--

FRONT-TO-BACK ADJUSTMENT IMPORTANT: Deck must be level side-to

side. If the following front-to-back adjust- ment is necessary, be sure to adjust both

front links equally so mower will stay level side-to-side.

To obtain the best cutting results, the mower housing should be adjusted so

that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in

its highest position.

Check adjustment on right side of tractor. Measure distance "D" directly in front and behind the mandrel at bottom edge of mower housing as shown.

•Before making any necessary adjust- ments, check that both front links are equal in length. Both links should be approximately 10-3/8".

•If links are not equal in length, adjust one link to same length as other link.

Nut

Front Links

TO REPLACE MOWER BLADE DRIVE BELT

The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL-

•Remove mower from tractor (See "TO REMOVE MOWER" in this section of

this manual).

•Work belt off both mandrel pulleys and idler pulleys.

•Pull belt away from mower.

BELT INSTALLATION -

•Install new belt in reverse order of removal.

•Make sure belt is in all pulley grooves and inside all belt guides.

•Install mower in reverse order of removal instructions.

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Icraftsmani Limited 90 DAY Warranty on Battery Do not General OperationSlope Operation ChildrenService Grass can hide obstaclesCustomer Responsibilities Repair AgreementIiiiiii Before Removing Tractor from Skid Attach Steering Wheel Tools Required for AssemblyTo Remove Tractor from Carton Unpack CartonCheck Battery HOW to SET UP Your TractorInstall Seat Check Deck Levelness To Convert to Bagging or DischargingCheck Tire Pressure Check for Proper Position of ALL BeltsH L Know Your Tractor AmmeterHOW to USE Your Tractor On Hills To Adjust Gauge WheelsTo Transport Check Engine OIL Level Before Starting the EngineADD Gasoline To Start EngineAutomatic Transmission Warm UP Purge TransmissionMulching Mowing Tips Mowing TipsGeneral Recommendations Before Each USEBlade Removal BatteryBlade Care To Sharpen BladeTransaxle Cooling To Clean Battery and TerminalsBelts Transaxle Pump FluidEngine OIL Filter AIR FilterIN-LINE Fuel Filter To Install Mower To Remove MowerBelt Installation To Level Mower HousingSIDE-TO-SIDE Adjustment To Replace Mower Blade Drive BeltTo Replace Motion Drive Belt To Adjust BrakeTransaxle Motion Control Lever Neutral Adjustment Transmission REMOVAIJREPLACE- MentTo Remove Wheel for Repairs To Adjust Steering Wheel ALIGN- MentFront Wheel TOE-IN/CAMBER To Attach Jumper CablesInterlocks and Relays To Remove Hood and Grill AssemblyTo Replace Headlight Bulb To Replace FuseTo Adjust Carburetor Acceleration TestEngineoil EngineFuel System CylindersCause Troubleshooting ChartProblem CorrectionTroubleshooting Chart Problem Cause Correction ChargeSchematic Tractor - Model NumberTRACTOR-- Model Number Electrical Electrical KEY Part DescriptionTRACTOR-- Model Number 917.271142 Chassis and Enclosures Tractor - Model Number Chassis and Enclosures KEY Part NO. NO.DESCRIPTIONGround Drive Tractor - Model Number Tractor - Model Number Ground Drive KEY Part DescriptionTractor - Model Number 917.271142 Steering Assembly Tractor - Model Number Steering Assembly AssemblyEngine Optional EQUIPMENT23 Muffler Tractor - Model Number Seat Assembly Decals Wheels & TiresTractor - Model Number Lift Assembly KEY Part NO. NO.DESCRIPTION Tractor - Model Number Mower Deck KEY Part NO. no 1322749OO Part KEY Description 142892Cylinder HEAD, Valve and Breather Crankcase Cylinder HEAD/VALVE/BREATHER Crankcase KEY Part Description Lifter, valveIgnition / Electrical Blower Housing and Baffles AIR Intake Hex. flange AIRINTAKE/FILTRATION82 @ Part Description Engine Controls01L PAN!LUBRICATION Crankshaft J Fuel System Exhaust Page Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across HillGet it fixed, at your home or ours

917.271142 specifications

The Craftsman 917.271142 is a versatile and robust lawn mower that caters to homeowners seeking an efficient solution for their yard care needs. This model is designed for residential use and combines cutting-edge technology with user-friendly features, making it an excellent choice for both experienced and novice gardeners.

One of the standout features of the Craftsman 917.271142 is its powerful 21-inch steel deck, which provides an ideal cutting width for tackling a variety of grass conditions. This deck is designed for durability, ensuring that it can withstand the rigors of lawn maintenance season after season. The mower's adjustable cutting height ranges from 1 to 4 inches, offering flexibility to achieve the desired grass length to suit individual preferences and seasonal variations.

The Craftsman 917.271142 is equipped with a reliable Briggs & Stratton engine, known for its potent performance and ease of start. This engine provides sufficient power to handle thick grass and tough terrain while ensuring consistent cutting results. Additionally, the mower includes a self-propelled feature, which significantly reduces fatigue during long mowing sessions, allowing users to navigate uneven landscapes effortlessly.

In terms of technology, the Craftsman 917.271142 integrates a mulch kit, allowing for efficient grass clipping recycling. This system breaks down clippings into fine pieces that can be evenly distributed back onto the lawn, promoting healthier soil and reducing waste. For those who prefer traditional bagging, the mower also features a rear bagger option, making cleanup a breeze.

User convenience is further enhanced by ergonomic design elements. The adjustable handle ensures a comfortable grip for different user heights and can be easily folded for compact storage. The mower's large rear wheels provide improved maneuverability on various terrains, giving users better control during operation.

Maintenance is straightforward due to the mower's design, enabling easy access to the air filter and spark plug, which simplifies routine check-ups and repairs. Overall, the Craftsman 917.271142 combines power, efficiency, and user-centric features to make lawn care less of a chore and more of an enjoyable outdoor activity. Whether you are dealing with an expansive yard or a smaller garden, this mower is engineered to deliver reliable performance year after year.
Top Page Image Contents