Craftsman 247.77635 manual Storage, Chipper Shredder, Engine

Page 17

STORAGE

Chipper Shredder

Clean the equipment thoroughly.

Wipe equipment with an oiled rag to prevent rust.

Store unit in a clean, dry area. Do not store next to corrosive materials such as fertilizer.

Engine

Engines stored over 30 days need special attention.

1. To prevent gum from forming in fuel system or on essential carburetor parts:

a.if fuel tank contains oxygenated or reformulated gasoline (gasoline blended with an alcohol or an ether), run engine until it stops from lack of fuel, or

b.if fuel tank contains gasoline, either run engine until it stops from lack of fuel, or add a gasoline additive to the gas in the tank. If you use a gas additive, run the engine for several minutes to circulate the additive through the carburetor.

Then, engine and fuel can be stored up to 24 months.

2.While engine is still warm, change oil.

3.Remove spark plug and pour about one (1) oz. (30 ml.) of engine oil into spark plug hole. Replace spark plug and slowly pull the starter rope to distribute oil.

4.Clean engine of surface debris, chaff or grass.

5.Store in a clean, dry area.

WARNING: Do not store in same area as a stove, furnace, water heater, or other appliance that uses a pilot light or has a device that can create a spark.

17

Image 17
Contents Sears, Roebuck And Co., Hoffman Estates, IL 60179 U.S.A Horse PowerModel No Warranty Table of ContentsTraining SafetyOperation Page Removing Unit From Carton AssemblyLoose Parts In Carton See Figure Lowering the Chipper ChuteAttaching The Debris Collection Bag HousingEmptying the Debris Collection Bag Debris Collection BagOperation Meets Ansi safety standardsKnow Your Chipper Shredder Operating Controls See FigureStopping Engine Gas And Oil Fill-upTamper HopperGasoline Starting EngineType of Fuel Fuel Fill-upClearing the Hopper ShreddingChipping Cleaning the Reduction ChamberLubrication MaintenanceAir Cleaner Changing Oil Cleaning EngineSpark Plug Disconnecting Spark Plug Service and AdjustmentsReplacing the Chipper Blades Replacing the Shredder BladeChamber Carburetor AdjustmentEngine StorageChipper Shredder Problem Cause Remedy TroubleshootingSears Emission Control Defects Warranty Coverage Sears Craftsman 7.5 H.P. Chipper Shredder Model Parts ListPart Description Sears Craftsman 7.5 H.P. Chipper Shredder Model Carburetor Gasket SET 222 Repair Manual Cylinder Assembly Nut Governor Control Lever 777S32258 777D07574 777S32272 Engine LabelsGarantía ÍndiceGarantía limitada de la cortadora trituradora Craftsman 247.776350Capacitación SeguridadFuncionamiento Motor Extracción de la unidad de la caja MontajePiezas sueltas en la caja Ver Figura Deslizamiento hacia abajo del canal de la cortadoraColocación de la bolsa de recolección de desechos Vaciado de la bolsa de recolección de desechosConozca las propiedades de la cortadora trituradora OperaciónCumple con los estándares de seguridad de Ansi Controles de funcionamiento Ver FiguraAceite se envía una botella de 20 onzas junto con la unidad Carga de gas y aceiteDetención del motor Gasolina Encendido del motorAdvertencia Sea sumamente Tipo de combustibleCorte TrituraciónLimpieza de la tolva Cámara de reducciónLimpieza del canal de reducción Filtro de aire MantenimientoLubricación Cambio de aceite Limpieza del motorBujía de encendido Reemplazo de las hojas de la cortadora Servicio Y AjustesReemplazo de la hoja de la trituradora Desconexión de la bujíaAjuste del carburador Cortadora trituradora AlmacenamientoProblema Causa Remedio Guía Para LA Solución DE ProblemasResponsabilidades del Propietario de la Garantía Acuerdo De Protección Para Reparaciones Repair Protection AgreementsOur Home Your HomeSears Parts & Repair Center MY-HOME1-800-469-4663