Craftsman 127.28877, 127.28876 manual Setup iNSTRUCTiONS, Final Preparations

Page 22

SETUP iNSTRUCTiONS

4. FINAL PREPARATIONS

Check the engine and hydraulic oil levels. Top offwith the correct oil if necessary. Use 10W30 motor oil for the engine. Use fresh, clean 20W50 motor oil for the hydraulic system.

Insure Battery cables are connected properly.

'--IAWARNING Battery acid is caustic. Fumes are explosive and can cause serious injury or death.

Use insulated tools, wear protective glasses or goggles and protective clothing when working with batteries. Read and obey the battery manufacturer's instructions.

Be certain the ignition switch is OFF and the key has been removed before servicing the battery.

a)Verify battery polarity before connecting or disconnecting the battery cables.

b)When installing the battery, always assemble the RED, positive ( + ) battery cable first and the ground, BLACK, negative ( - ) cable last.

c)Tighten cables securely to battery terminals and apply a light coat of silicone dielectric grease to terminals and cable ends to prevent corrosion. Keep terminal covers in place.

Read Operation and Safety Manual before starting. Operator Manual is located under the seat. Tilt seat forward to access manual.

--Ii,

OperatoCs Manual is located

If deck does not cut level, see deck leveling procedure in the Operator's Manual

Run engine at full RPM for 5 minutes before engaging blades to allow the engine to be fully lubricated before load is applied.

Check the hydrostat neutral adjustment. Neutral is set at the factory but may require readjustment. See adjustments section in the operator's manual.

Do not use the machine without an approved grass collector, the grass discharge chute or mulching plates correctly fitted.

20

Page 21 Page 23
Image 22
Page 21 Page 23
Contents CRA MAN 4163202 Rev. B 11-2008 PARTSMANUAL4163201California Wash Hands After HandlingAdjustments Table of ContentsMaintenance Craftsman Professional Limited WarrantySignal word definitions Become AlertSite preparation and circumstances Preparing for Safe OperationMachine preparation Operating SafelyStarting Interrupting operationManeuvering Safely GeneralMaintenance Safety BladesBatterywarning Equipment58 -= =DO not Operate WiTH 2720743 Filler neck For TightnessOperators Manual is located 2e80iVolt Power Outlet Power Take OFF PTO Switch PChoke C Fuel Selector Valve U Controls Pushing the Machine PRE-OPERATION Check LiST Tire Pressure Tools Required for AssemblyUncrate Unit Traction LeversSetup iNSTRUCTiONS Final PreparationsOperator Presence iNTERLOCK System FuelingBefore Starting the Engine Starting the EngineOperating Notes DrivingCutting Cutting TiPSMaintenance Chart Maintenance Record Battery Check DailyLubrication After First Five 5 Hours Engine OILSpark Plugs DailyDual Element AIR Cleaner Fuel FilterSpecific Torques Engine CoolingPurging Transaxles Transaxles Transaxle Fluid ChangeBlade Balance Blade InstallationBlade Removal SharpeningHeight of CUT Deck LevelingDeck Rollers Parking Brake Hydrostatic TRANSA×LE ADJUST= Ments Hydro Transaxle Drive Belt Cutterdeck BeltSpindle Deck Belt Tension0 F E S 0 N a L MAN 4163202 Rev. B 11-2008 MANUALDEPIEZAS4163201California CalifornieReemplazo Contenido PaginaLista DE Verificacion Antes DE LA Operacion Establezca InformacionIATENCION IMANTENGASE Alerta SeguridadIAVISO Definici6n de las palabras de avisoPreparacion y circunstancias del sitio Lea el iVianual de operaci6n yPreparacion de la maquina Operacion SeguraInterrupci6n de la operaci6n ArranqueNeutra Ivianobrar SiN Peligro AdvertenciaCuchillas Seguridad DE MantenimientoEn general CombustibleBatera Advertencia Etiquetas No Opere LA Unidad SIN EtjquetasPiezas EN Movimiento LA CubiertaEtiquetas Etiquetas AdvertencaFreno DE Estacionamiento El Manual del propietario se encuentra debajo del asientoPresion de los neumaticos Obturador C PotenciaPOWER Take OFF, PTO PControles DesactivadoValvula Selectora DE Combustible U Controles Empuje DE LA Maquina Lista DE Verificacion Antes DE LA Operacion Responsabilidad DEL OperadorEstablezca Instructiones Presion DE LOS NeumaticosPreparativos Finales Operacion Antes DE Arranoar EL MotorConduccion Notas DE OperacionCorte Sugerencias DE CorteTabla DE Mantenimiento Iiii !i litititititi!itititititititititil Regstro DE MantenmentoMantenimiento BateraMantenimiento LUBRICAClONBujas Cambios Periodicos DE AceiteAceite DEL Motor DiariamenteFiltro DEL Combustible Filtro DE Aire DE Elemento DobleEnfriamiento DEL Motor AprieteTransejes Cambio DE Fluido DEL TransejeDesmontaje DE LA Cuchilla Equilibrio DE LAS CuchillasAfilacion Instalacion DE LA CuchillaNivelacion DE LA Plataforma AjustesAltura DE Corte NotasFreno DE Mano DesembragadoAjustes DEL Transeje Hidrostatico Tension DE LA Correa Reemplazo DE CorreasCorrea DE LA Plataforma DE LA Cortadora Your Home Call anytime, day or night U.S.A. and Canada

127.28876, 127.28877 specifications

The Craftsman 127.28877 and 127.28876 are a pair of high-performance cordless drills designed for both professional tradespeople and DIY enthusiasts. These models exemplify the blend of power, versatility, and user-friendly design that Craftsman tools are known for.

One of the standout features of both models is their brushless motor technology. This innovation enhances efficiency, delivering more power and runtime than traditional brushed motors. It also reduces heat generation, leading to prolonged tool life. With a high-torque output, these drills can easily handle demanding applications, making them ideal for tasks such as drilling into wood, metal, and masonry.

Both models come equipped with a two-speed transmission. This feature allows users to select the optimal speed based on the specific task at hand—whether it’s high-speed drilling for smaller holes or low-speed drilling for driving larger fasteners. The variable speed trigger further provides enhanced control, enabling a precise and seamless drilling experience.

The design of the Craftsman 127.28877 and 127.28876 is ergonomic, featuring a soft-grip handle that minimizes hand fatigue during extended use. The compact and lightweight structure allows for easy maneuverability in tight spaces, making it suitable for various job sites.

Another notable characteristic is the LED work light integrated into the drills, providing illumination in dimly lit areas. This feature ensures that users can work effectively without needing to reposition other lighting sources.

Battery compatibility is another key advantage of these models. Both drills utilize the Craftsman 20V MAX battery platform, allowing users to interchange batteries between different tools within the same line. This feature not only enhances convenience but also maximizes productivity by reducing downtime due to battery changes.

Finally, the construction of the Craftsman drills includes rugged materials that resist wear and tear, assuring durability over years of use. With a combination of advanced technology, user-centered design, and robust performance, the Craftsman 127.28877 and 127.28876 are invaluable additions to any tool collection, providing reliability and efficiency for a range of projects.
Top Page Image Contents