Craftsman 127.28877, 127.28876 manual Machine preparation, Operating Safely

Page 6

SAFETY

Machine preparation

Check operator presence interlock system and brake operation. Adjust or repair any problems before using.

Do not tamper with or defeat safety devices. Keep guards, shields and interlock safety devices in place and in proper working condition. They are for your protection.

Keep all fasteners such as nuts, bolts and pins well secured.

Visually inspect blades, blade bolts and the cutter assembly for wear or damage. Replace worn or damaged blades and bolts to preserve balance.

Verify that machine and attachments, if any, are in good operating condition.

Do not engage blades until ready to mow.

OPERATING SAFELY

in general

Use extra care when loading or unloading the machine into a trailer or truck.

Slow down and use caution when making turns and crossing roads and sidewalks. Stop blades if not mowing.

Do not run the engine in an enclosed area where dangerous carbon monoxide fumes can collect.

Do not place your foot on the ground while operating the machine.

Before operating, lower the discharge chute, install the mulcher or put the entire grass catcher in place.

Keep clear of the discharge opening at all times. Never direct the discharge toward a bystander. Stop operation if someone approaches.

Keep washout ports and other mower housing service openings closed when mowing.

Use care when pulling loads or using heavy equipment.

Use only approved draw bar hitch points. Limit loads to those you can safely control.

Do not turn sharply. Use care when reversing. Use counter-weight(s) or wheel weights when suggested in the operator's manual.

Never leave a machine unattended. Always turn off blades, set parking brake, stop engine and remove key before dismounting.

4

Page 5 Page 7
Image 6
Page 5 Page 7
Contents CRA MAN 4163202 Rev. B 11-2008 PARTSMANUAL4163201California Wash Hands After HandlingAdjustments Table of ContentsMaintenance Craftsman Professional Limited WarrantySignal word definitions Become AlertSite preparation and circumstances Preparing for Safe OperationMachine preparation Operating SafelyStarting Interrupting operationManeuvering Safely GeneralMaintenance Safety BladesBatterywarning Equipment58 -= =DO not Operate WiTH 2720743 Filler neck For TightnessOperators Manual is located 2e80iPower Take OFF PTO Switch P Volt Power OutletChoke C Fuel Selector Valve U Controls Pushing the Machine PRE-OPERATION Check LiST Tire Pressure Tools Required for AssemblyUncrate Unit Traction LeversSetup iNSTRUCTiONS Final PreparationsOperator Presence iNTERLOCK System FuelingBefore Starting the Engine Starting the EngineOperating Notes DrivingCutting Cutting TiPSMaintenance Chart Maintenance Record Battery Check DailyLubrication After First Five 5 Hours Engine OILSpark Plugs DailyDual Element AIR Cleaner Fuel FilterEngine Cooling Specific TorquesPurging Transaxles Transaxles Transaxle Fluid ChangeBlade Balance Blade InstallationBlade Removal SharpeningDeck Leveling Height of CUTDeck Rollers Parking Brake Hydrostatic TRANSA×LE ADJUST= Ments Hydro Transaxle Drive Belt Cutterdeck BeltSpindle Deck Belt Tension0 F E S 0 N a L MAN 4163202 Rev. B 11-2008 MANUALDEPIEZAS4163201California CalifornieReemplazo Contenido PaginaLista DE Verificacion Antes DE LA Operacion Establezca InformacionIATENCION IMANTENGASE Alerta SeguridadIAVISO Definici6n de las palabras de avisoPreparacion y circunstancias del sitio Lea el iVianual de operaci6n yPreparacion de la maquina Operacion SeguraArranque Interrupci6n de la operaci6nNeutra Ivianobrar SiN Peligro AdvertenciaCuchillas Seguridad DE MantenimientoEn general CombustibleBatera Advertencia Etiquetas No Opere LA Unidad SIN EtjquetasPiezas EN Movimiento LA CubiertaEtiquetas Etiquetas AdvertencaEl Manual del propietario se encuentra debajo del asiento Freno DE EstacionamientoPresion de los neumaticos Obturador C PotenciaPOWER Take OFF, PTO PControles DesactivadoValvula Selectora DE Combustible U Controles Empuje DE LA Maquina Lista DE Verificacion Antes DE LA Operacion Responsabilidad DEL OperadorEstablezca Instructiones Presion DE LOS NeumaticosPreparativos Finales Operacion Antes DE Arranoar EL MotorConduccion Notas DE OperacionCorte Sugerencias DE CorteTabla DE Mantenimiento Iiii !i litititititi!itititititititititil Regstro DE MantenmentoMantenimiento BateraMantenimiento LUBRICAClONBujas Cambios Periodicos DE AceiteAceite DEL Motor DiariamenteFiltro DEL Combustible Filtro DE Aire DE Elemento DobleEnfriamiento DEL Motor AprieteTransejes Cambio DE Fluido DEL TransejeDesmontaje DE LA Cuchilla Equilibrio DE LAS CuchillasAfilacion Instalacion DE LA CuchillaNivelacion DE LA Plataforma AjustesAltura DE Corte NotasFreno DE Mano DesembragadoAjustes DEL Transeje Hidrostatico Reemplazo DE Correas Tension DE LA CorreaCorrea DE LA Plataforma DE LA Cortadora Your Home Call anytime, day or night U.S.A. and Canada

127.28876, 127.28877 specifications

The Craftsman 127.28877 and 127.28876 are a pair of high-performance cordless drills designed for both professional tradespeople and DIY enthusiasts. These models exemplify the blend of power, versatility, and user-friendly design that Craftsman tools are known for.

One of the standout features of both models is their brushless motor technology. This innovation enhances efficiency, delivering more power and runtime than traditional brushed motors. It also reduces heat generation, leading to prolonged tool life. With a high-torque output, these drills can easily handle demanding applications, making them ideal for tasks such as drilling into wood, metal, and masonry.

Both models come equipped with a two-speed transmission. This feature allows users to select the optimal speed based on the specific task at hand—whether it’s high-speed drilling for smaller holes or low-speed drilling for driving larger fasteners. The variable speed trigger further provides enhanced control, enabling a precise and seamless drilling experience.

The design of the Craftsman 127.28877 and 127.28876 is ergonomic, featuring a soft-grip handle that minimizes hand fatigue during extended use. The compact and lightweight structure allows for easy maneuverability in tight spaces, making it suitable for various job sites.

Another notable characteristic is the LED work light integrated into the drills, providing illumination in dimly lit areas. This feature ensures that users can work effectively without needing to reposition other lighting sources.

Battery compatibility is another key advantage of these models. Both drills utilize the Craftsman 20V MAX battery platform, allowing users to interchange batteries between different tools within the same line. This feature not only enhances convenience but also maximizes productivity by reducing downtime due to battery changes.

Finally, the construction of the Craftsman drills includes rugged materials that resist wear and tear, assuring durability over years of use. With a combination of advanced technology, user-centered design, and robust performance, the Craftsman 127.28877 and 127.28876 are invaluable additions to any tool collection, providing reliability and efficiency for a range of projects.
Top Page Image Contents