HOW to Stop Your Unit

IMPORTANT

Experience indicates that alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during stor- age. Acidic gas can damage the fuel system of an engine while in storage.

To avoid engine problems, empty the fuel sys- tem before storage for 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season.

Never use engine or carburetor cleaner prod- ucts in the fuel tank or permanent damage may occur. See the STORAGE section for addi- tional information.

S To stop the engine, push and release the engine ON/STOP switch. The switch will automatically return to the ON position. Wait 5 seconds before attempting to restart unit to allow switch to reset.

SIf engine does not stop, move choke to the FULL CHOKE position.

Engine

Choke Lever

ON/STOP

Switch

FULL HALF OFF

HOW TO START YOUR UNIT

WARNING: The trimmer head will turn while starting the engine. Avoid any con- tact with the muffler. A hot muffler can cause serious burns.

STARTING A COLD ENGINE (or a warm engine after running out of fuel)

Starting Position

1.Set unit on a flat surface.

2.Slowly press the primer bulb 6 times.

3.Move choke lever to the FULL CHOKE position.

4.Squeeze the throttle trigger fully and hold through all remaining steps.

Starter Handle

Choke

Lever

Muffler

Primer Bulb

5.Pull starter rope handle sharply until engine sounds as if it is trying to start, but do not pull rope more than 6 times.

6.As soon as engine sounds as if it is trying to start, move choke lever to HALF CHOKE position.

7.Pull starter rope sharply until engine runs, but no more than 6 pulls.

NOTE: If the engine doesn’t start after 6 pulls (at the HALF CHOKE position), move the choke lever to the FULL CHOKE position and press the primer bulb 6 times. Squeeze and hold the throttle trigger and pull the starter rope 2 more times. Move the choke lever to the HALF CHOKE position and pull the start- er rope until the engine runs, but no more than 6 pulls. If the engine still doesn’t start, it is probably flooded. Proceed to

STARTING A FLOODED ENGINE.

8.Once the engine starts, allow it to run 10 seconds, then move the choke lever to the OFF CHOKE position. Allow the unit to run for 30 more seconds at OFF CHOKE before releasing the throttle trig- ger.

NOTE: If engine dies with the choke le- ver in the OFF CHOKE position, move the choke lever to the HALF CHOKE position and pull the rope until engine runs, but no more than 6 pulls.

STARTING A WARM ENGINE

1.Move the choke lever to the HALF CHOKE position.

2.Squeeze and hold the throttle trigger. Keep throttle trigger fully squeezed until the en- gine runs smoothly.

3.Pull starter rope sharply until engine runs, but no more than 5 pulls.

4.Allow engine to run 15 seconds, then move the choke lever to OFF CHOKE.

NOTE: If engine has not started, pull starter rope 5 more pulls. If engine still does not run, it is probably flooded.

STARTING A FLOODED ENGINE

Flooded engines can be started by placing the choke lever in the OFF CHOKE position; then, pull the rope to clear the engine of ex- cess fuel. This could require pulling the starter handle many times depending on how badly the unit is flooded.

If the unit still doesn’t start, refer to TROUBLESHOOTING TABLE or call 1-800-554-6723.

530086927 specifications

The Weed Eater 530086927 is a versatile and powerful tool designed for homeowners and landscaping professionals alike. This gas-powered string trimmer offers a perfect balance of performance, ergonomics, and convenience, making it an ideal choice for trimming grass and weeds around the yard.

One of the standout features of the Weed Eater 530086927 is its robust 25cc two-cycle engine. This engine delivers reliable power and efficiency, allowing users to tackle even the toughest overgrown areas with ease. The engine’s design ensures smooth operation and reduces emissions, making it an environmentally friendly choice.

In terms of functionality, the Weed Eater 530086927 is equipped with a bump feed line advance system. This feature allows for quick and easy line replacement during use; users simply bump the trimmer head on the ground to release more line, ensuring continuous work without interruptions. The trimmer head accommodates .095-inch line, providing the cutting power necessary for heavy-duty tasks.

The ergonomic design of the Weed Eater 530086927 enhances user comfort, particularly during extended periods of use. It features a lightweight build, which minimizes fatigue and strain on the user. The adjustable handle allows for customizable operation angles, ensuring that users can maintain an ideal posture while trimming.

Additionally, the Weed Eater 530086927 boasts a straight shaft design. This characteristic not only enhances reach and maneuverability but also allows users to access tight spots and hard-to-reach areas with precision. The straight shaft is particularly beneficial for maintaining edges along sidewalks, fences, and garden beds.

Another notable technology incorporated into the Weed Eater 530086927 is its easy starting system. This ensures that users can get the trimmer running with minimal hassle, reducing the time spent on setup and allowing more time for yard work.

In summary, the Weed Eater 530086927 is a feature-rich, user-friendly string trimmer that combines power, efficiency, and comfort. Ideal for both casual users and professionals, it provides the necessary tools to keep your yard immaculate and well-maintained. Whether you are tackling simple maintenance or rough overgrowth, this trimmer is engineered to meet your needs effectively.